Table of Contents
Advertisement
・How to set the transition time to the power save mode
T he transition time to the power save mode can be selected from among 30
minutes, 1 hour, 2 hours, and 4 hours in the time/calendar setting mode.
The default setting is 30 minutes.
Refer to "How to set the power save mode" on page 117.
2
※ You can make the power save setting also from the application.
I f synchronization of settings except for automatic time synchronization is
performed, the settings are overwritten by those on the application side.
※ I f the sensor function is used in a dark place, it is recommended that the pow-
er save function is turned off or the transition time to the power save mode is
set for longer than the time the watch is used. For normal use, turn the power
save function on.
※ U nder the following conditions, the power save mode and sleep mode are not
activated.
・The remaining amount of battery power is suffi cient. （
・The mountaineering data is being recorded in the altimeter mode.
・The stopwatch is measuring.
106
（1）How to perform pairing
※ For pairing, operation of both watch and smartphone is required.
① Start the exclusive application installed in the smartphone.
② O perate the application and select Synchronize setting. Communication is started.
③ P ress and hold Button Ⓓ on the watch side until a confi rmation sound beeps to
set to the Bluetooth mode.
④ S tart pairing according to the instructions on the application screen. If connection
3
has succeeded, is turned on. Pairing registration is performed automatically, and
then data communication is executed.
⑤ W hen data communication is completed, the connection is cancelled automatically and is turned off .
⑥ I f connection has failed, Err appears at the bottom row, and the screen returns
to the initial screen. Start the procedure from ① again.
An animation that indicates
connection appears at the top.
Ⓓ
Ⓓ
Press and hold
Connection start
108
）
Connection completed
Connection failure
With Bluetooth devices, devices to be connected to each other should be reg-
istered in advance. This registration is called pairing. Once pairing is performed,
the pairing information is registered in the watch and the smartphone, and is
recognized automatically afterward.
Re-pairing is required in the following cases.
・When system reset of the watch is made.
・ W hen the pairing information is deleted because of repairing of the watch,
etc.
・When the model of the smartphone is changed.
・When pairing of the devices is cancelled by the smartphone or watch.
・ W hen another watch will be registered in the smartphone. Then, cancel the
pairing with the current watch and perform pairing with the new watch.
※ O nly one pair of a watch and a smartphone can be connected at a time. To manage multiple
watches in one application, perform pairing and cancellation both in the body of the watch and
the application as necessary.
※ Make sure that communication between the watch and the smartphone is activated.
（2）How to cancel pairing
※ To cancel pairing, operation of both watch and smartphone is required.
※ There is no infl uence on your data such as a mountaineering plan/ record although you cancel pairing.
■ Watch side
① P ress and hold Button Ⓓ and Button Ⓔ at the same time with the time and cal-
endar displayed. PAIRING CLEAR appears at the top row and HOLd at the
middle row. Hold down the buttons continuously. When the outer circumference
graphic rotates once, a confi rmation sound beeps, and pairing is cancelled.
■ Smartphone side
① S elect Bluetooth from the settings of the smartphone and delete the de-
vice for which pairing is registered.
※ N ote that re-pairing is not possible unless registration information of both watch and
smartphone is deleted.
Hold down
Button Ⓓ and
Ⓓ
Button Ⓔ
at the same time
Ⓔ
Pairing
PAIRING CLEAR
completed
3
107
3
109
Advertisement
Table of Contents
