Bacharach Neutronics Mini-ICS Operation Manual page 4

Oxygen analyzer / controller
Table of Contents

Advertisement

2.1.3.1 Oxygen Sensor Input ................................................................................................... 2-6
2.1.3.2 Flow Switch Status Input ............................................................................................. 2-6
2.1.3.3 Oxygen Alarm Relay Outputs ...................................................................................... 2-6
2.1.3.4 Inert Gas Control Relay Outputs ................................................................................. 2-7
2.1.3.5 Fault Relay Outputs ..................................................................................................... 2-7
2.1.3.6 Remote Calibration Relay Outputs .............................................................................. 2-7
2.1.3.7 Analog Voltage Output ................................................................................................ 2-8
2.1.3.8 Analog Current Output ................................................................................................ 2-8
2.1.3.9 Range ID Output.......................................................................................................... 2-8
2.1.3.10 RS-232 Service Port .................................................................................................... 2-9
2.1.3.11 Battery Backup ............................................................................................................ 2-9
2.1.3.12 Mains Power .............................................................................................................. 2-10
2.2
STEP 1 - Power Up the unit ......................................................................................... 2-11
2.2.1
STEP 2 - Calibrate the Unit .......................................................................................... 2-12
2.2.2
STEP 3 -Set Alarms, and Inert Gas Control Limits ...................................................... 2-12
2.2.3
2.2.3.1 Set Oxygen Alarm Level ............................................................................................ 2-12
2.2.3.2 Set High Inert Gas Control limit ................................................................................. 2-12
2.2.3.3 Set Low Inert Gas Control limit .................................................................................. 2-12
3
CHAPTER 3 - ANALYZER OPERATION ..................................................................... 3-1
3.1
3.2
3.2.1
CALIBRATE Mode .......................................................................................................... 3-1
3.2.1.1 When to calibrate ........................................................................................................ 3-1
3.2.1.2 What gases to use ....................................................................................................... 3-1
3.2.1.3 Procedure for calibrating the Model Mini-ICS ............................................................. 3-2
3.2.2
ALARM Mode ..................................................................................................... 3-3
2
3.2.3
SET HIGH INERT GAS CONTROL LIMIT Mode ............................................................ 3-3
3.2.4
SET LOW INERT GAS CONTROL LIMIT Mode ............................................................ 3-3
3.2.5
VIEW ACTIVE FAULTS Mode ........................................................................................ 3-3
3.3
............................................................................................................................ 3-4
3.3.1
NORMAL Mode ............................................................................................................... 3-4
3.3.2
ALARM ACTIVE Mode............................................................................................... 3-4
2
3.3.3
INERTING CONTROL ACTIVE Mode ............................................................................ 3-4
3.3.4
FAULT ACTIVE Mode ..................................................................................................... 3-5
4
CHAPTER 4 - MAINTENANCE AND TROUBLESHOOTING ...................................... 4-1
4.1
4.1.1
System Setup via Front Panel Keypad ........................................................................... 4-1
4.1.1.2 User Setup 2: O2 Alarm Relays Ascending Trip. ........................................................ 4-2
4.1.1.3 User Setup 3: Analog Voltage Output Setting. ............................................................ 4-2
4.1.1.4 User Setup 4: Analog Current Output Setting. ............................................................ 4-2
Manual Part Number:
5-06-4900-53-0
............................................................................................................ 3-1
......................................................................................................................... 3-1
........................................................................................................................ 4-1
Revision Level: C
ECO 044952
..................................................................... 2-11
Revision Date:
May 08, 2018
Page iv

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Neutronics Mini-ICS and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents