Yamaha MO6 Owner's Manual page 51

Knob
Changing the sounds
You can change the brightness and tone characteristics of the current Voice, Performance, Song or Pattern in realtime by
turning the knobs while you play. Rotating it to the right (clockwise) increases the program number, while rotating it to the left
(counter-clockwise) decreases it. You can select the function set assigned to the knobs among the following seven sets by
pressing the appropriate Control function button.
Function sets assigned to the Knobs
Button of which the
Operation
lamp is turned on
When pressing the [PAN/ [PAN/SEND] button
SEND] button
When pressing the [TONE] [TONE] button
button
When pressing the [ARP [ARP FX] button
FX] button
When pressing the [EQ] [EQ] button
button
When pressing the [PAN/ [PAN/SEND] button
SEND] button and the [TONE] button
[TONE] button
simultaneously
When pressing the [TONE] All the buttons are off
button and the [ARP FX]
button simultaneously**
When pressing the [ARP [ARP FX] button
FX] button and the [EQ] [EQ] button
button simultaneously
* For Drum Voices, this affects the release time for all played notes, whether held or released.
** Available only when setting the Zone Switch to on in the Master Mode (page 215)
When pressing any of the Control function buttons, the lamp(s) of the buttons will light according to the above table, and the
status of the Knobs and Control sliders (currently assigned functions and set values) is shown on the LCD display. The
appearance of the knob and slider in the display indicates the actual control status of the knob and slider.
When a knob graphic in the display is black or a slider graphic is shown with a shadow, the corresponding Knob or Control
slider on the panel affects the sound as indicated.
A white knob graphic or a slider graphic without a shadow indicates that the current Knob or Control slider position differs
from the actual parameter value. In this case, moving the knob or slider does not affect the sound until the knob or slider
position reaches the parameter's current value (after which the knob graphic turns black or the slider graphic has a
shadow).
DAW REMOTE PAGE SELECT
PAN SEND
ASSIGN
TONE
ARP FX
MEF
EQ
KN1 (Knob 1)
Pan (stereo position)
of the Voice/
Performance
Filter Cutoff
Frequency (degree of
brightness)
Swing degree of the
Arpeggio playback
Low band of the
Master EQ in the
Voice/Performance
mode, part EQ in the
Song/Pattern mode
Function assigned from the [UTILITY]
CTLASN [SF2] ASSIGN display (page 208) in
the Utility mode
Function assigned for each Master from the [MASTER]
display (page 217)
Function assigned to the Master Effect parameters from the [UTILITY]
MEF display.
ASSIGN A ASSIGN B ASSIGN 1 ASSIGN 2
PAN REVERB CHORUS TEMPO
CUTOFF RESONANCE ATTACK RELEASE
SWING GATE TIME VELOCITY UNIT MULTIPLY
LOW LOW MID HIGH MID HIGH
Using the Controllers on the MO
Functions controlled by each Knob
KN2 (Knob 2) KN3 (Knob 3)
Reverb Send Level Chorus Send Level
Resonance (the level Attack Time of the
of the signal in the sound
area of the cutoff
frequency)
Gate time (length) of Velocity of the
the Arpeggio Arpeggio playback
playback
Low-mid band of the High-mid band of the
Master EQ in the Master EQ in the
Voice/Performance Voice/Performance
mode, Mid band of mode. (Not available
the Part EQ in the in the Song/Pattern
Song/Pattern mode mode.)
[F4] Function assigned for each Voice from the
[VOICE]
CTLSET display (page 155)
[EDIT]
Adjusting these knobs/sliders affects the sound immediately.
Adjusting these knobs/sliders will not affect the sound until
the current value is reached.
KN4 (Knob 4)
Tempo of the Song/
Pattern/Arpeggio
playback
Release Time of the
sound (decay time
after the key is
released)*
Arpeggio playback
time
High band of the
Master EQ in the
Voice/Performance
mode, part EQ in the
Song/Pattern mode
[EDIT] [COMMON] [F4]
Zone selection [F5] KN/CS
[F4] CTLASN [SF5]
Owner's Manual 51