Song Job Mode - Yamaha MO6 Owner's Manual

RPN
(Registered Parameter Number)
FMSB-LSB
FDATA (Data Entry MSB-LSB)
n
Normally three types of control change data are sent: RPN MSB (101), RPN LSB (100), and Data Entry MSB (6). In this synthesizer, Data Entry LSB (38) is added to
this and the resulting group of control change events is handled as one in this display.
NRPN (Non Registered
Parameter Number)
FMSB-LSB
FDATA (Data Entry MSB-LSB)
n
Normally three types of control change data are sent: NRPN MSB (99), NRPN LSB (98), and Data Entry MSB (6). In this synthesizer, this group of control change
events is handled as one in this display. For a complete list of the available RPN and NRPN numbers and their corresponding controls, refer to the MIDI Data Format
in the separate Data List booklet.
Exclusive (System Exclusive)
FDATA (HEX)

Song Job mode

The Song Job mode contains a comprehensive set of editing tools and data transform functions you can use to change the sound of the
Song. It also includes a variety of convenient operations, such as copying or erasing data.
After setting parameters as required from the selected display, press the [ENTER] button to execute the Job.
CAUTION
An "Executing..." message is shown when it takes a short amount of time to execute the Job. Never attempt to turn off the power while an
"Executing..." message is shown. Turning the power off in this state results in loss of all user data.
[F1] UNDO/REDO
The Undo Job cancels the changes you made in your most recent recording session, editing session, or Job, restoring the data to its previous state. This
allows you to recover from accidental data loss. Redo is available only after using Undo, and lets you restore the changes you made before undoing them.
CAUTION
Undo/Redo does not work with Mixing Voice operations.
[F2] NOTE (Note data Job)
n
Before executing the Note data Job, make sure that you specify the track (01–16, all) and range (measure : beat : clock) to which the Job is applied.
01: Quantize
TR (Track)
001 : 1 : 000 – 999 : 4 : 479
Quantize (Resolution)
Strength
This event changes parameter values for each tone generator Part. This event is used to set Part settings such
as Pitch Bend Sensitivity or Tuning.
See page 225.
Settings: 000 – 127
See page 225.
Settings: 000 – 127, ***
These events are used to change the parameter values for each tone generator Part. They can be is used to
edit sounds via MIDI, allowing you to edit filter or EG settings, or adjust the pitch or level for each instrument of
a drum voice.
See page 225.
Settings: 000 – 127
See page 225.
Settings: 000 – 127, ***
A type of MIDI message used to exchange data unique to a specific model or type of device.
Unlike other MIDI events, these events differ depending on the manufacturer/device, and are incompatible
among different devices.
See page 226.
Settings: 00 – 7F, F7 (Data must be entered in hexadecimal format.)
[SONG] Song selection
Quantization is the process of adjusting the timing of note events by moving them closer to the nearest exact
beat. You can use this feature, for example, to improve the timing of a performance recorded in real time.
Determines the track (01-16, all) and range of measures/beats/clocks over which the Job is applied.
Determines to what beats the note data in the specified track will be aligned.
Settings: 32nd note, 16th note triplet, 16th note, 8th note triplet, 8th note, 1/4 note triplet, 1/4 note, 16th note + 16th note triplet,
8th note + 8th note triplet
The Strength value sets the "strength" by which note events are pulled toward the nearest quantize beats.
A setting of 100% produces exact timing. A setting of 0% results in no quantization.
Settings: 000%–100%
Song Job mode
[JOB]
Owner's Manual
183