Eaton PowerXL DA1 Communications Manual page 57

Modbus Display Parameter name
Register
157 P-29 f-MidV/f
158 P-30 Start Mode
159 P-31 Digital Reference Reset Mode
160 P-32 t-DCBrake@Stop
161 P-33 Spin Start Enable
162 P-34 Brake Chopper
163 P-35 AI1 Gain
164 P-36 RS485-0 Address
164 P-36 RS485-0 Baudrate
164 P-36 Modbus RTU0 COM Timeout
165 P-37 Password Level2
166 P-38 Parameter Lock
167 P-39 AI1 Offset
168 P-40 Display Scale
169 P-41 PID1 Kp
170 P-42 PID1 Ti
171 P-43 PID1 Mode
172 P-44 PID1 Set Point 1 Source
173 P-45 PID1 Set Point Digital
174 P-46 PID 1 Feedback 1 Source
175 P-47 AI2 Signal Range
176 P-48 t-Standby
177 P-49 PID1 WakeUpLevel
178 P-50 CAN0 Baudrate
179 P-51 SwitchRemanentStorage
180 P-52 ParameterAccess
181 P-53 Action@Communication Loss
182 P-54 RO1 Hysteresis
183 P-55 RO1 Switch-On Delay
Access
rw/ro
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Modbus RTU for variable frequency drive DA1, DC1, DE1 09/16 MN040018EN www.eaton.com
3.2 Parameters for DC1 variable frequency drives
Scaling
RUN/
STOP
STOP 50 ≙ 50 Hz
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 250 ≙ 25 s
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 100 ≙ 10 %
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 300 ≙ 30 %
RUN 100 ≙ 0.10
RUN 10 ≙ 1.0
RUN 10 ≙ 1.0 s
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 100 ≙ 10 %
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 10 ≙ 1.0 s
RUN 100 ≙ 10 %
RUN 1 ≙ 1
RUN 1≙ 1
RUN 1 ≙ 1
RUN 1 ≙ 1
RUN 100 ≙ 10 %
RUN 10 ≙ 1.0 s
3 Parameter
Value range Data
format
0 - P-09 U16
0 - 6 U16
0, 1, 2, 3 U16
0, 0 - 250 U16
0, 1 U16
0, 1 U16
0 - 5000 U16
0 - 63 U16
1 - 6 U16
0 - 8 U16
0 - 9999 U16
0, 1 U16
-5000 - +5000 U16
0 - 6000 U16
1 - 300 U16
0 - 300 U16
0, 1 U16
0, 1 U16
0 - 1000 U16
0, 1, 2, 3 U16
0, 1, ..., 5 U16
0 - 250 U16
0 - 1000 U16
0, 1, 2, 3 U16
0, 1 U16
0, 1 U16
0, 1, 2, 3, 4 U16
0 - 1000 U16
0 - 250 U16
53