Table of Contents
Advertisement
4
Tank
4. Move handle to
Chemical Tank Rinse
5
(SPRAY MODE)
5. Move handle to Tank
Vent (SPRAY MODE)
ire t
Calibrate
1. Move handle to To
2
Calibrate
2. Move handle to O
(SPRAY MODE)
3. Move handle to Pump
Suction from Rinse
4
Tank (SPRAY MODE)
4. Move handle to
Chemical Tank Rinse
5
(SPRAY MODE)
5. Move handle to Tank
Vent (SPRAY MODE)
Flush
1. Move handle to To
2
Boom (SPRAY MODE)
2. Move handle to O
(SPRAY MODE)
3. Move handle to Pump
Suction from Rinse
4
Tank
4. Move handle to
Chemical Tank Rinse
5
(SPRAY MODE)
5. Move handle to Tank
Vent (SPRAY MODE)
Calibrate
1. Move handle to To
2
Calibrate
- Chapter 12 - Optional Accessories
2. Move handle to O
(SPRAY MODE)
3. Move handle to Pump
Suction from Rinse
e i al n e tion
3
Pump Suction
Pump Suction
Pump Suction
Pump Suction
from Chemical Tank
from Chemical Tank
from Rinse Tank
from Rinse Tank
Spray mode
Direct injection is NOT recommended for
powder mixes, granules, or suspended concentrates
crop damage may result.
Drain
Drain
Probe
Probe
i
1
Calibrate
Do not run pump in this
position unless camlock
cap is removed
Off
Off
Recirculate
Recirculate
Do not run pump
in this position
To Boom
To Boom
Spray mode
Direct Chemical
Direct Chemical
Injection
Injection
3
Pump Suction
Pump Suction
Pump Suction
Pump Suction
from Chemical Tank
from Chemical Tank
from Rinse Tank
from Rinse Tank
Spray mode
Direct injection is NOT recommended for
powder mixes, granules, or suspended concentrates
crop damage may result.
Drain
Drain
Probe
Probe
1
Calibrate
Do not run pump in this
position unless camlock
cap is removed
Off
Off
Recirculate
Recirculate
Do not run pump
in this position
To Boom
To Boom
Spray mode
Direct Chemical
Direct Chemical
Injection
Injection
3
Pump Suction
Pump Suction
Pump Suction
Pump Suction
from Chemical Tank
from Chemical Tank
from Rinse Tank
from Rinse Tank
Spray mode
Direct injection is NOT recommended for
powder mixes, granules, or suspended concentrates
crop damage may result.
Drain
Drain
Probe
Probe
1
Calibrate
Do not run pump in this
position unless camlock
cap is removed
Off
Off
Recirculate
Recirculate
Do not run pump
in this position
To Boom
To Boom
Spray mode
Direct Chemical
Direct Chemical
Injection
Injection
4
Tank Rinse
Tank Rinse
Rinse mode
5
Tank Vent
Fill mode
Spray mode
Calibrate
Calibrate
tart
i e
Off
Off
Spray mode
Valve must be o
Valve must be o
to operate transcal
to operate transcal
2
Vacuum to
Product 4
If the Direct Chemical Injection tank is over lled,
chemical may be drawn into the main carrier/product tank.
Always turn valve to o position when lling is nished.
4
Chemical
Chemical
Chemical
Chemical
Chemical
Spray mode
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Rinse mode
5
Fill mode
Tank Vent
Spray mode
Calibrate
Calibrate
Off
Off
Spray mode
Valve must be o
Valve must be o
to operate transcal
to operate transcal
2
Vacuum to
Product 4
If the Direct Chemical Injection tank is over lled,
chemical may be drawn into the main carrier/product tank.
Always turn valve to o position when lling is nished.
4
Chemical
Chemical
Chemical
Chemical
Chemical
Spray mode
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Tank Rinse
Rinse mode
5
Tank Vent
Fill mode
Spray mode
Calibrate
Calibrate
Off
Off
Continued over page
Spray mode
Valve must be o
Valve must be o
to operate transcal
to operate transcal
2
Vacuum to
Product 4
Prairie Pro Operator's Manual MY19 - REV 2
If the Direct Chemical Injection tank is over lled,
chemical may be drawn into the main carrier/product tank.
Always turn valve to o position when lling is nished.
Chemical
Chemical
Spray mode
Advertisement
Table of Contents
