1. Manuals
  2. Brands
  3. PROFACE Manuals
  4. Desktop
  5. PL-5700 Series
  6. Manual

PROFACE PL-5700 Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Digital's PL-5700 series of Panel Computers (hereafter referred to as the "PL") are
multipurpose factory automation (FA) computers, which embody Digital's latest,
cost-effective architecture.
Before using the PL, be sure to read this manual thoroughly to familiarize yourself
with the PL's operation procedures and functions.
The word "PL" refers to the following models:
1. It is forbidden to copy the contents of this manual in whole, or in part, without the
permission of the Digital Electronics Corporation.
2. The information in this manual is subject to change without notice.
3. This manual was written with care; however, if you should find any error or omis-
sions, please contact Digital and inform them of your findings.
4. Please be aware that Digital is not responsible for damages resulting from the use
of our products, regardless of article 3.
5. Specifications set out in this manual are for overseas products only,and,as a
result,some differences may exist between the specifications given here and the
Japanese ones.
Product names used in this manual are the trademarks of their respective manufac-
turers.
© Copyright 1997, Digital Electronics Corporation
MS-DOS
®
IBM
PL-5700 Series User's Manual
Preface
PL-5700T1-24VC
PL-5700T1
PL-5701T1
PL-5700S1
PL-5701S1
PL-5700L1
PL-5701L1
®
®
and Windows
are registered trademarks of the Microsoft Corporation.
®
DOS
are registered trademarks of IBM.
(with CE marking)
(Standard 100V unit)
(Standard 100V unit)
(Standard 100V unit)
(Standard 100V unit)
(Standard 100V unit)
(Standard 100V unit)
NOTE:
1

Advertisement

Table of Contents
loading

Summary of Contents for PROFACE PL-5700 Series

  • Page 1 Preface Digital’s PL-5700 series of Panel Computers (hereafter referred to as the “PL”) are multipurpose factory automation (FA) computers, which embody Digital’s latest, cost-effective architecture. Before using the PL, be sure to read this manual thoroughly to familiarize yourself with the PL’s operation procedures and functions.

  • Page 2: Preface

    Safe Product Usage This manual contains a variety of safety markings to help you safely and correctly operate Digital’s PL-5700 series of Panel Computers, which includes the PL-5700T1, PL-5701T1, PL-5700L1, PL-5701L1, PL-5700S1, PL-5701S1, and PL-5700T1- 24VC. Be sure to keep this manual handy for future reference.
  • Page 3 • Avoid exposing and operating the PL in direct sunlight, high temperatures and humidity, and in areas where excessive dust and vibration will occur. PL-5700 Series User’s Manual...
  • Page 4 - use the Display OFF feature; if the same image is to be displayed for a long period of time. - change the screen display periodically to prevent the displaying of a single image for a long period of time. PL-5700 Series User’s Manual...

  • Page 5: Table Of Contents

    Table of Contents Preface Preface ......................1 Safe Product Usage..................2 Safety Precautions ..................2 Table of Contents ..................5 Before Using the PL ..................8 Features......................9 Unpacking the PL ..................10 Information Symbols ................... 10 Chapter 1 Overview 1-1 System Configuration ..................
  • Page 6 6-3 Other Files ....................6-13 1. DISP.EXE (Display ON/OFF Program) ..........6-13 2. FANALARM.EXE (CPU Cooling Fan Alarm Detection Program)..6-13 ® ® 3. BLSAVER.SCR (Windows 3.1 Screen Saver / Windows 95 Screen Saver) ..6-13 PL-5700 Series User’s Manual...
  • Page 7 Chapter 7 Maintenance and Inspection 7-1 Cleaning the Display ................. 7-1 7-2 Replacing the 100V Unit’s Backlight ............7-2 7-3 Periodic Check ..................7-3 Appendices 1. Hardware Configuration ................A-1 1. I/O Mapping ..................A-1 2. Memory Mapping ................A-3 3.

  • Page 8: Before Using The Pl

    95, install the PL-5700 Driver & Utility Disk’s Display Driver. (For installation information, see the disk’s README.TXT file) • For information on the PL-5700’s bundled utility software, see the README.TXT file on the Driver & Utility Disk. PL-5700 Series User’s Manual...

  • Page 9: Features

    Special Features The main features of PL series displays are as follows: The Latest, High-Performance Architecture Designed around the AMD 5x86 133 MHz CPU, the PL utilizes the type of high performance architecture used by most PC compatibles. Bright 10.4" LCD with a Wide Viewing Angle The PL’s large 10.4-inch 640 ´...

  • Page 10: Unpacking The Pl

    Indicates terms or items that require further explanation. See the footnote on that page. Indicates pages containing related information. 1. 2. Indicates steps used to accomplish a given task. Be sure to follow these steps in the order they are written. PL-5700 Series User’s Manual...

  • Page 11: Chapter 1 Overview

    * Devices in dotted boxes are Digital optional products or commercially available products. The figure above shows simply the internal data flow and the PL’s peripheral connec- tions, and may differ from the actual layout used by the customer. PL-5700 Series User’s Manual...

  • Page 12: Options

    Moisture res is tant packing used when ins talling the PL . res is tant GP570-WP00-MS S ame as P L's original packing. packing Software Options TT-WIN for Windows ® Mouse emulation utilities for the touch panel's screen ® TT- W I N for Windows PL-5700 Series User’s Manual...

  • Page 13: Series Panel Types

    S : STN color LCD 1 : 1-slot type T : TFT color LCD Expansion Slots 1-Slot type 3-Slot Type Display PL-5701L1 PL-5700L1 B/W LCD PL-5701S1 PL-5700S1 STN color LCD PL-5700T1/ PL-5701T1 PL5700T1-24VC TFT color LCD PL-5700 Series User’s Manual...
  • Page 14 MEMO This page is intentionally left blank. PL-5700 Series User’s Manual...

  • Page 15: Chapter 2 Specifications

    With s tand 1500 VAC , 20 mmA for one minute (between charging terminal and FG voltage terminal) Ins ulation Min. 10MW at 500 V DC (between charging terminal and FG terminal) res is tanc e Panel Computer PL-5700 Series User’s Manual...

  • Page 16: Environment Specifications

    PL-5701T1, PL-5701S1, PL-5701L1 : 321 mm (W) x 272 mm (H) x 96.3 mm (D) P L-5700T 1, P L-5700S1 : 5.5 kg P L-5701T1, PL-5701S 1 : 4.6 kg Weight P L-5700L1 : 4.7 kg P L-5701L1 : 3.8 kg (excluding acces s ories) PL-5700 Series User’s Manual...

  • Page 17: Performance Specifications

    R S-485 C OM3 Terminal board Interface P rinter C entronics s tandard (DB 25-pin female connector) K eyboard P S/2 interface (Mini DIN 6-pin female connector) Mouse P S/2 interface (Mini DIN 6-pin female connector) PL-5700 Series User’s Manual...

  • Page 18: Display Functions

    • The higher the contrast between the foreground and background colors is, the more likely that crosstalk will occur. Either changing the color combination or decreasing the contrast may help to reduce the amount of cross talk. See “5-2, System Parameters.” PL-5700 Series User’s Manual...
  • Page 19 (pallet numbers 0, 12, 10, 9, 14, 13, 11, and 15) - may appear better than displays using different colors. • If you wish to use halftones, be sure to check their display quality during actual PL operation. PL-5700 Series User’s Manual...

  • Page 20: Expansion Slots

    • The PL does not supply -5 or -12 V. As a result, ISA (AT) bus compatible boards which require -5 or -12 V are not available. • All the DB connectors for external interfaces are equipped with inch type connector screw threads. PL-5700 Series User’s Manual...

  • Page 21: Interface Specifications

    TCS7568-43-201 manufactured by HOSHIDEN, or equivalent Compatible keyboards (example) : FKB1424-001 (compact type) by FUJITSU FKB4874-101 Mouse Interface Pin No. Signal MOUSE DATA Mini DIN 6-pin female connector MOUSE CLK TCS7568-43-201 manufactured by HOSHIDEN, or equivalent PL-5700 Series User’s Manual...

  • Page 22: Rs-232C Interface (Com1/Com2)

    Ground) terminals. If this is not done, the RS-485 (RS- 422) circuit may be damaged. Pin No. Signal M3 screws <Interface Circuit> SN751178N or equivalent Use the GND and FG terminals only when the connected device requires them. PL-5700 Series User’s Manual...

  • Page 23: Jumper Settings

    In the drawing below, indicates a shorted jumper, and indicates an open jumper. Jumper Setting Factory-default COM2: To set pin 9 to: RI input RI input 5 V output RS-485 output-side terminator Terminator enabled RS-485 input-side terminator Terminator enabled PL-5700 Series User’s Manual...

  • Page 24: Using The Contrast Adjustment Knob

    1. Loosen the dummy unit’s six attachment screws, located on the bottom and side of the PL. Side View Remove the dummy unit. To increase the contrast, rotate the control clockwise. To decrease it, rotate the control counter-clockwise. PL-5700 Series User’s Manual 2-10...

  • Page 25: External Features

    The PL-5700T1-24VC, PL-5700T1, PL-5700S1, and PL-5700L1 each have three slots, designated as “slot 1,” “slot 2,” and “slot 3,” starting from the one closest to the front panel. The PL-5701T1, PL-5701S1, and PL5701L1 provide one slot, designated as “slot 1.” PL-5700 Series User’s Manual 2-11...
  • Page 26 24V DC unit - connect the customer’s pro- vided cord here. To avoid danger of electrical shocks or fire, be sure to turn the PL’s power OFF before connecting the power cord or any peripheral devices to the PL. PL-5700 Series User’s Manual 2-12...

  • Page 27: Dimensions

    PL-5700T1-24VC, PL-5700T1, PL-5700S1, PL-5700L1: <General Dimensions> Measured in mm, excluding projections) Top panel Effective area 211.2 ( W ) x 158.4 ( H ) Side panel Front panel 129.3 (116.1) 13.2 Side panel Rear panel PL-5700 Series User’s Manual 2-13...

  • Page 28: 5701T1, Pl-5701S1, Pl-5701L1 : General Dimensions

    Specifications PL-5701T1, PL-5701S1, PL-5701L1: <General Dimensions> Measured in mm, excluding projections Top panel Effective area 211.2 ( W ) x 158.4 ( H ) Side panel Front panel 96.3 (83.1) 13.2 Side panel Rear panel PL-5700 Series User’s Manual 2-14...

  • Page 29: Installation Hole Dimensions

    Measured in mm 292.0 • Allowable panel/plate thickness is from 1.6 to 10 mm. • To obtain maximum moisture-resistance, be sure to mount the PL on a flat, smooth panel, free of any dents or deformations. PL-5700 Series User’s Manual 2-15...
  • Page 30 Specifications MEMO This page intentionally left blank. PL-5700 Series User’s Manual 2-16...

  • Page 31: Chapter 3 Installing Optional Units And Expansion Boards

    3MB silicon dis k unit compatible with hard P L-F F000 Ins ide the PL. dis ks F l a sh file disk unit 10MB s ilicon disk unit compati ble with P L-F F001 Ins ide the PL. hard dis ks PL-5700 Series User’s Manual...
  • Page 32 PL and will void your warranty. <Main Memory> Be sure to use only DIM modules manufactured by Digital. Installing other DIM modules may result in either damage to or failure of the PL, and will void your warranty. PL-5700 Series User’s Manual...

  • Page 33: Installing Options And Expansion Boards

    If you use only one module, be sure to install it in BANK 0. If you use two modules, install the first in BANK 0, and the second in BANK 1. Rear maintenance cover 1. Unscrew and remove the rear main- tenance cover. BANK 1 (Upper socket) DIMM sockets BANK 0 (Lower socket) PL-5700 Series User’s Manual...
  • Page 34 4. Refit the rear maintenance hatch, and tighten the screw. <Removing the DIM module> Carefully spread the clips on both edges of the DIM module, in the direction of the arrows, to remove the module. Removing from BANK Removing from BANK PL-5700 Series User’s Manual...

  • Page 35: Installing The External Cache Memory Board (Pl-Ec000)

    2. Attach the external cache memory board to the cache board connector, and lock it down by tightening the two screws which came with the memory board. 3. Refit the rear maintenance hatch, and retighten the screw. PL-5700 Series User’s Manual...
  • Page 36 Note: This drawing shows the PL-5700T1 unit (3-slot type) HDD cover Remove the HDD cover. HDD connector 2) Insert the PL-HD000 unit’s attachment cable into the HD connector. Be sure the cable’s red line is facing the direction shown here. Red Line PL-5700 Series User’s Manual...
  • Page 37 <PL-HD000 Connector> CAUTION: If the pins are in- serted incorrectly, the unit may be damaged Do not use Connect the these pins cable to here Place the cover back in place, and fasten its screws. PL-5700 Series User’s Manual...
  • Page 38 HD unit. (See Reference Line) 5) Screw the left and right side Reference spacers into the HD unit’s Line attachment face screw holes. 6) Attach the PL-HD000 unit. Face the side with the Heat Protector upwards PL-HD000 PL-5700 Series User’s Manual...
  • Page 39 CAUTION: If the pins are in- serted incorrectly, the unit may be Do not use Connect the these pins damaged cable to here 8) Place the cover back in place, and fasten its attachment screws in place. PL-5700 Series User’s Manual...

  • Page 40: Installing The Fdd Unit (Pl-Fd000/Fd001)

    Side panel of the PL If the PL-FD000 is installed, the dummy unit will no longer be neces- sary. Remove the dummy unit. FDD connector 2. Attach the PL-FD000 cable to the FDD connector. PL-FD000 PL-5700 Series User’s Manual 3-10...
  • Page 41 Bottom panel of the PL 1. Loosen the six screws on the side and bottom panels of the PL to remove the dummy unit or optional PL-MC000 unit. The figure shows the 3-slot type of PL-5700T1 PL-5700 Series User’s Manual 3-11...
  • Page 42 4. Take the PL-FD001 cable out as shown in the figure, and slide the dummy unit or optional PL- MC000 toward the front panel to set it in place. Then, tighten the six attachment screws on the PL’s side and bottom panels. PL-5700 Series User’s Manual 3-12...

  • Page 43: Installing The Memory Card Interface Unit (Pl-Mc000)

    PL. Then, tighten the unit’s six at- tachment screws on the side and bottom panels of the PL. Front Panel If you plan to also install the PL- FD001 (for development and mainte- nance), first attach the PL-FD001, then the PL-MC000. PL-5700 Series User’s Manual 3-13...

  • Page 44: Installing The Ide Slave Adapter (Pl-Sa000)

    DC power cord to both the DC IN- PUT on the CD-ROM drive and the PL. CD-ROM drive To IDE connection cable INTERFACE Make sure that pin 1 of the CD-ROM drive connection cable matches pin 1 of the IDE INTERFACE. PL-5700 Series User’s Manual 3-14...

  • Page 45: Installing The Flash Rom Board (Pl-Fr000)

    2. Attach the PL-FR000 to the optional- board connector, and lock it in place with the four mounting screws which came with the PL-FR000. PL-FR000 3. Replace the rear maintenance cover and tighten the screw. PL-5700 Series User’s Manual 3-15...

  • Page 46: Installing An Expansion Board

    PL’s internal screw holes, and externally, attach Re-attach the screw (1) which came with the expansion filler strip board. Then, replace the filler strip and removed in step 1 tighten the strip’s two screws. PL-5700 Series User’s Manual 3-16...

  • Page 47: Chapter 4 Installation And Wiring

    (See figure on left) Then, use a screwdriver to insert the two cover attach- ment screws into their respective cover holes (use only M3x6 screws). When the maintenance cover is secured, replace the Front maintenance cover previously removed unit. Panel Computer PL-5700 Series User’s Manual...
  • Page 48 PL and any other objects. (The clearance must be large enough to allow you to insert or remove expansion boards and to attach connec- tors.) Rear panel Side panel 50mm 50mm 50mm 50mm 50mm 50mm 50mm PL-5700 Series User’s Manual...
  • Page 49 Secure the rear panel of PL in place with the mounting brakets (4) Hook the mounting brackets into the two mounting holes on the top face, and the two holes on the bottom face of the PL’s body. Mounting hole (Top and bottom faces) PL-5700 Series User’s Manual...
  • Page 50 Use a driver to tighten the bracket’s adjustment screw. To ensure a high degree of moisture resistance, the torque should be 0.5 to 0.6 N.m. Panel Excessive torque may damage the panel or bracket. PL-5700 Series User’s Manual...

  • Page 51: Wiring The Pl

    AC100V L = AC Input Terminal—live line AC100V N = AC Input Terminal—neutral line = Ground Terminal connected to the FP chassis 24V Unit +24V PL-5700T1-24VC +24V Power Terminal Block Crimp-on Ring Screw size : Terminals PL-5700 Series User’s Manual...
  • Page 52 φ φ φ φ φ 3.2 mm or larger Max. 6.0 mm • The colors in the figure above are for the cable which came with the 100V 3. Reattach the protective transparent cover. Transparent cover PL-5700 Series User’s Manual...

  • Page 53: Cautions: 100V Pl-5700T*/S*/L* Units

    • Ground the lightning surge absorber (E1) and the PL (E2) separately. • Select a lightning surge absorber which will not exceed the allowable circuit voltage, even Lightning surge absorber when the voltage rises to the maximum. PL-5700 Series User’s Manual...

  • Page 54: Grounding Cautions

    • To improve noise immunity, it is recommended to attach a ferrite core to the power cord. *1 Use a grounding resistance of less than 100 Ω and a 2mm or greater thickness wire, or your country’s applicable standard. For details, contact your local GP distributor. PL-5700 Series User’s Manual...

  • Page 55: Setup Procedures

    Lists the keys available for setting up the PL. Help display area Provides detailed information about the item at the cursor position. System set-up area Lists system parameters for the selected menu. Menu bar Contains four menus: Main, Advanced, Power and Exit. PL-5700 Series User’s Manual...
  • Page 56 ( ), a submenu will appear. Pressing the [ESC] key on the submenu will return you to the main menu. [F10] : Returns the parameters listed in the system setup area to the CMOS’s current values. PL-5700 Series User’s Manual...

  • Page 57: System Parameters

    If no floppy disk drive is installed, select the “Not Installed” option. Selecting other options may cause an error. * If the optional flash ROM board is installed, set this parameter to “1.44 MB, 3 1/2.” PL-5700 Series User’s Manual...

  • Page 58: Main

    If a correct set is not found, select the “User” option and set val- ues for the “Cylinders,” “Heads,” “Sectors/Track,” and “Write Precomp” param- eters. Set the “IDE Adapter 0 Slave” parameters in the same way. PL-5700 Series User’s Manual...
  • Page 59 • The PL-5700T1 and PL-5701T1 do not have a brightness adjustment or a contrast setting. The PL-5700S1 and PL-5701S1 also do not have a brightness setting. The default setting is [Standard/4]. System Memory Extended Memory The main and extended memory amounts will appear. PL-5700 Series User’s Manual...

  • Page 60: Advanced

    IDE adapter: [Enabled] ↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ F1 Help Select Item -/+ Change Values F9 Setup Defaults ← → ← → Exit Select Menu Enter Select Sub-Menu F10 Previous Values PL-5700 Series User’s Manual...
  • Page 61 [Disabled], this setting is also disabled. Diskette controller The selections include [Disabled] or [Enabled]. The factory setting is [Enabled] and is recommended. IDE adapter The selections include [Disabled] or [Enabled]. The factory setting is [Enabled] and is recommended. PL-5700 Series User’s Manual...
  • Page 62 Normal IO Wait State Large Disk Access Mode If your hard disk contains 528 MB or more of memory, select the type of OS to be used. DOS : MS-DOS Other : OS other than MS-DOS PL-5700 Series User’s Manual...

  • Page 63: Power

    Standby. ↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ F1 Help Select Item -/+ Change Values F9 Setup Defaults ← → ← → ESC Exit Select Menu Enter Select Sub-Menu F10 Previous Values PL-5700 Series User’s Manual...

  • Page 64: Exit

    Select this option to return the parameter settings to the default. Load Previous Values Select this option to load the parameter settings from the CMOS. Save Changes Select this option to store your changes in the CMOS. 5-10 PL-5700 Series User’s Manual...

  • Page 65: Chapter 6 Bundled Software

    T ou c h P a ne l. Panel Computer PL-5700 Series User’s Manual...
  • Page 66 F or setti ng contras t with the PL-5700S1 and P L-5701S 1 when equipped with the C ONTS ET.E XE backlight brightness and contras t control utility for the P L-5700L1 and P L- 5701L1. PL-5700 Series User’s Manual...

  • Page 67: Touch Panel Input File

    Y = 0 ~ 26 (30,25) (30,26) : Touch panel effective area The touch panel handler cannot be used in conjunction with the TT-WIN mouse ® ® emulator on Windows . Cancel the resident program before starting up Windows PL-5700 Series User’s Manual...
  • Page 68 PLCALIB.EXE application, the following message appears on the screen, and the system will start up in a mode that does not calibrate data. WARNING!! Can’t open CAL file. Stay resident. • Unless properly calibrated, the display and touch panel input positions may not be the same. PL-5700 Series User’s Manual...
  • Page 69 1: Input off BX = Y coordinate in 640 x 480 mode (-40 - 519) DX = X coordinate in 640 x 480 mode (0 - 639) CX = Number of valid input buffers on analog touch panel PL-5700 Series User’s Manual...
  • Page 70 When the PLATPH.EXE application resides in memory, returns a fixed message and version. Input AX = FE00h Output AH = 0: Successfully completed BL = ‘Y’ Bit15 BH = ‘B’ 1 0 0 0 CX = Version No. PLATPH.EXE Version No. ID code Carry = Clear PL-5700 Series User’s Manual...
  • Page 71 BH = Y coordinate range in PL-386 compatibility mode (0 - 26) BL = X coordinate range in PL-386 compatibility mode (0 - 30) CX = Number of valid data sets in touch panel input buffers PL-5700 Series User’s Manual...
  • Page 72 S egment of 1s t coordinate code lis t Offset of 2nd coordinate code lis t S egment of 2nd coordinate code lis t Offset of nth coordinate code lis t S egment of nth coordinate code lis t PL-5700 Series User’s Manual...
  • Page 73 BL = X coordinate range in PL-386 compatibility mode (0 - 30) CX= Number of valid data sets in touch panel input buffers DX= Coordinate code To use function 0400h, it is necessary to first register the coordinate codes. PL-5700 Series User’s Manual...
  • Page 74 Returns the touch panel’s current status Input AX = 0500h Output AH = Status in PL-386 compatibility mode Bit 1 B it 0 Des cription Area pres s e d Unchanged Not available Area released PL-5700 Series User’s Manual 6-10...
  • Page 75 Processing until touch Input? panel area is released Function 0500h Touch panel area held down Bit 0 Coordinates changed while touch panel area Bit 1 is pressed. To next touch panel input PL-5700 Series User’s Manual 6-11...

  • Page 76: Plcalib.exe (Touch Panel Data Calibration)

    Touch upper left and lower right cornner of the screen. two points will light up, in both the [Enter] : Go to test mode. [Esc] : Terminate program. upper left-hand and lower right-hand Upper left Lower right corners. (0000,0000) (0000,0000) PL-5700 Series User’s Manual 6-12...
  • Page 77 [↵] key. • When specifying the data file name for the pa- rameter (-C=[path name]) at the PLCALIB.EXE start-up, the program ends without displaying the message shown on the left. PL-5700 Series User’s Manual 6-13...

  • Page 78: Other Files

    If no input is made from the keyboard, mouse or touch panel within the set amount of time, the backlight will turn off. The backlight turns back on when input is made from the keyboard, mouse or touch panel. PL-5700 Series User’s Manual 6-14...

  • Page 79: Chapter 7 Maintenance And Inspection

    Do not use sharp or hard objects, such as a mechanical pencil or screwdriver, to push on the display. This could damage the unit. Protection sheet Use the screen protection sheet when us- ing the unit in especially dirty or dusty ar- eas. PL-5700 Series User’s Manual...

  • Page 80: Replacing The 100V Unit's Backlight

    PL, secure it in place with the attachment screw, and re-attach the connector. 4. Replace the backlight’s cover and tighten its attachment screw. Be careful not to pinch the connector lines between the PL body and this cover. PL-5700 Series User’s Manual...

  • Page 81: Periodic Check

    Is the connection cable firmly connected (not loose) ? Are any bolts or screws loose ? Are there any flaws or tears in the moisture resistant packing ? • Display check Is the display bright enough ? PL-5700 Series User’s Manual...
  • Page 82 Maintenance and Inspection MEMO PL-5700 Series User’s Manual...

  • Page 83: Hardware Configuration

    For information on I/O bit mapping, see the next page. *1 : The game I/O is not used by the PL system, but is reserved as standard. *2 : The PL system uses these addresses: do not assign them to other devices. PL-5700 Series User’s Manual App-1...
  • Page 84 *1 : The PL system uses this bit. Do not assign it to other devices. This bit must be always “1,” do not write “0” for it. *2 : You cannot read this bit for the purpose of editing or overwriting data. PL-5700 Series User’s Manual App-2...

  • Page 85: Memory Mapping

    *1 : This area is reserved for extended boards. *2 : This area is occupied only when the optional memory card interface unit is installed. *3 : This area is occupied only when the optional flash ROM board unit is installed. PL-5700 Series User’s Manual App-3...

  • Page 86: Irq Mapping

    F l o ppy dis k controller DMA 3 DMA 4 C as cade to controller 1 DMA 5 For 16-bit transmission DMA 6 DMA 7 *1 : IRQ 9 is not used by the PL, but reserved as standard. PL-5700 Series User’s Manual App-4...

  • Page 87: Serial Communications

    COM1 int86 (0x14,&ir,&or) ; ir.h.ah 0x01 ; /* 1 character output */ ir.h.al 0x32 ; ‘2’ ir.x.dx COM1 int86 (0x14,&ir,&or) ; • Changing commands or parameters also changes function (mode setting, data reception, etc.). PL-5700 Series User’s Manual App-5...

  • Page 88: Printer Cable Connections

    • 25 GND 13 • •13 SLCT 31 • 14 • 32 • 15 • 33 • 16 • 34 • 17 • 35 • 18 • 36 • • • • • Connector Port Shield PL-5700 Series User’s Manual App-6...

  • Page 89: Touch Panel Handler Sample Program

    * Input can be performed by pressing on designated areas of the screen. * Before starting this program, be sure to start the PLATPH.EXE program #include <stdlib.h> #include <stdio.h> #include <dos.h> #include <graph.h> #include <conio.h> PL-5700 Series User’s Manual App-7...
  • Page 90 /* Function Sheet F4 */ 320, -40, 399, -1, 0x1265, /* Function Sheet F5 */ 400, -40, 479, -1, 0x2166, /* Function Sheet F6 */ 480, -40, 559, -1, 0x2267, /* Function Sheet F7 */ PL-5700 Series User’s Manual App-8...
  • Page 91 " C ", 0x63, /* Function Sheet F3 */ " D ", 0x64, /* Function Sheet F4 */ " E ", 0x65, /* Function Sheet F5 */ " F ", 0x66, /* Function Sheet F6 */ PL-5700 Series User’s Manual App-9...
  • Page 92 "ENT", 0x0d, /* Function Sheet ENT*/ union REGS inregs, outregs; /*************/ /* BUZZER ON */ /*************/ void buzzer_on(void) int timer; outp (CTRL8253, 0xb6); outp (DATA8253+2, 0x33); outp (DATA8253+2, 0x05); /* Length of buzzer sounding */ PL-5700 Series User’s Manual App-10...
  • Page 93 = TP_CONDITION; int86(ATPH_SYS_CALL, &inregs, &outregs); if(outregs.h.ah == 3) /* Touch Panel Off */ break; else if(outregs.h.ah == 0) /* Touch Panel On */ inregs.x.ax = TP_IN_NOWAIT; int86(ATPH_SYS_CALL, &inregs, &outregs); /* ATPH Function Call*/ PL-5700 Series User’s Manual App-11...
  • Page 94 /* Time in area */ ((short)outregs.x.dx > tpcd[i].sx)&& ((short)outregs.x.bx > tpcd[i].sy)&& ((short)outregs.x.dx < tpcd[i].ex)&& ((short)outregs.x.bx < tpcd[i].ey)) inregs.h.ah = WRITE_DATA; inregs.x.cx = tpcd[i].key; int86(KEYBOARD_BIOS, &inregs, &outregs); buzzer_on(); wait_touch_off(); buzzer_off(); value=TRUE; break; PL-5700 Series User’s Manual App-12...
  • Page 95 /* KEYBOARD INPUT*/ /********************/ int keyboard_on(void) int i, ky; if(kbhit()) ky=getch(); for(i=0; kbcd[i].keycode; i++) if(ky == kbcd[i].keycode) printf("push key is [%s]. \r",kbcd[i].keyname); if(ky == ZKEYCODE) printf(" push [%s]key. finishprogram. \n",kbcd[i].keyname); return(TRUE); /* Program End break; PL-5700 Series User’s Manual App-13...
  • Page 96 /* ERROR:Program End */ _rectangle(_GBORDER,tpcd[0].sx,tpcd[0].sy,tpcd[0].ex,tpcd[0].ey); /* MAKE A SCREEN FRAME printf("please push touchpanel or key \n"); printf("End program by pressing [ Z ]key or screen. \n"); while(1) touchpanel_on(); if(keyboard_on()) _setvideomode(_DEFAULTMODE); /* RETURN TO VIDEOMODE */ exit(0); PL-5700 Series User’s Manual App-14...

  • Page 97: Bios Lists

    F arthes t left column in s croll down range D H = L owes t line in s croll down D L = range F arthes t right column in s croll down range PL-5700 Series User’s Manual App-15...
  • Page 98 01: Set attribute bit 7 to blink function. AH = R eading basic AL = B H = Value read pallet register B as ic pallet register to read (0 - B L = PL-5700 Series User’s Manual App-16...
  • Page 99 C h aracter generator bank No. character C X = Number of characters to regis ter DX = F irst character code to regis ter E S :BP = Top address in us er-defined table PL-5700 Series User’s Manual App-17...
  • Page 100 1: 14 lines video BIOS R OM) 2: 25 lines [Graphics ] 3: 43 lines D L = Number of s creen lines (W hen B L = 00h) PL-5700 Series User’s Manual App-18...
  • Page 101 AH = G ray s cale B L = AL = 12h S u cces s f u lly executed enable/disable AL = 0: G ray s cale enabled 1: G ray s cale disabled PL-5700 Series User’s Manual App-19...
  • Page 102 B H = Nonactive-dis play code S t a tus information AH = AL = 1B h : Succes s f u lly B X = Implementation type executed E S:DI = R eturn information buffer PL-5700 Series User’s Manual App-20...
  • Page 103 : 80287 C PU yes/no : No : Y es B its 13, 12, 8, 3, 2 & 0 : R es erved Operatio n Input O utput Reading memory AX =Memory size in 1 K B units size PL-5700 Series User’s Manual App-21...
  • Page 104 C y linder No. S i g nificant 2 bits (Bits DH = 7 - 8) DL = Head No. Drive No. (FDD: 00h - E S :B- 01h, HDD: 80h - 81h) B uffer address PL-5700 Series User’s Manual App-22...
  • Page 105 Max. number of cylinders C L = Max. number of usable s ectors and Significant bit in max. DH = number of cylinders Max. DL = number of usable heads Number of built-in hard dis k drives PL-5700 Series User’s Manual App-23...
  • Page 106 DL = tracks function. B its 5 - 0: Max. number of 00h and CY =1: Does not support s ectors tracks and per track 00h or C Y=1: number of tracks Drive No. per sector. PL-5700 Series User’s Manual App-24...
  • Page 107 0: S u cces s f u lly completed AL = 00h: Interval timer s tart 1: Error 01h: Interval timer stop E S :BX = E n d flag address C X:DX = Wait time in 1 µs ec units PL-5700 Series User’s Manual App-25...
  • Page 108 S S = DS value specified in E S:SI table Top address in below table C Y= 1: Error AH = F F h C S dummy (00h) G DI TEMP B I O S (00h) PL-5700 Series User’s Manual App-26...
  • Page 109 Device No. P rinter initialization AH = AH = Printer s tatus DX = Device No. S t a tus check AH = AH = Printer s tatus DX = Device No. PL-5700 Series User’s Manual App-27...
  • Page 110 *1 Backlight contrast control is available only on the PL-5700L1 and PL-5701l1. It is not supported by the PL-5700T1 or PL-5701T1. *2 8 contrast levels: D2, D1, D0, 000b (dark) ~ 111b (bright) Backlight brightness: D4, 0b (dark) ~ 1b (bright) PL-5700 Series User’s Manual App-28...

This manual is also suitable for:

Pl-5700t1-24vcPl-5700t1Pl-5701t1Pl-5700s1Pl-5701s1Pl-5700l1 ... Show all

Table of Contents