Emc Guide Line - gefran AFE200 Series Instruction Manual

73550-KXX-4/4A-MS 07
710kW
73550-XXX-4/4A-SL
73150-KXX-4/4A-MS 09
73150-XXX-4/4A-SL
900kW
73150-XXX-4/4A-SL
AFE200-73550-KXX-4/4A-MS 10
AFE200-73550-XXX-4/4A-SL
1MW
AFE200-73550-XXX-4/4A-SL
Sizes
72000-KXX-4-MS 04
400kW
72000-XXX-4-SL
72500-KXX-4-MS 05
500kW
72500-XXX-4-SL
73150-KXX-4/4A-MS 06
630kW
73150-XXX-4/4A 4-SL
73550-KXX-4/4A-MS 07
710kW
73550-XXX-4/4A-SL
73150-KXX-4/4A-MS 09
73150-XXX-4/4A-SL
900kW
73150-XXX-4/4A-SL
AFE200-73550-KXX-4/4A-MS 10
AFE200-73550-XXX-4/4A-SL
1MW
AFE200-73550-XXX-4/4A-SL

5.1.2 EMC guide line

Drives are designed to operate in an industrial environment where a high level
of electromagnetic interference are to be expected. Proper installation practices
will ensure safe and trouble-free operation. If you encounter problems, follow the
Attention
guidelines which follow.
-
-
-
-
-
2 x 185
2 x 185
2 x 185
2 x 185
2 x 185
2 x 185
2 x 185
2 x 185
Recommended cable cross-
(mm
2
150
150
150
150
185
185
185
185
185
185
185
185
185
185
Check for all equipment in the cabinet are well grounded using short, thick
grounding cable connected to a common star point or busbar. Better solution
is to use a conductive mounting plane and use that as EMC ground reference
plane.
Flat conductors, for EMC grounding, are better than other type because they
have lower impedance at higher frequencies.
Make sure that any control equipment (such as a PLC) connected to the
AFE200 is connected to the same EMC ground or star point as the AFE200
via a short thick link.
Separate the control cables from the power cables as much as possible, using
separate trunking, if necessary at 90º to each other.
Whenever possible, use screened leads for the connections to the control
AFE200 • Instruction Manual
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
2 x kcmil 350
Terminals:
Lock screw
section diameter
) AWG / kcmil
300 kcmil
300 kcmil
300 kcmil
300 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
350 kcmil
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
M10 50
(U,V,W=M12)
on mechanical cabinet
Recommen-
ded stripping
(mm) (mm)
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
M10 Occhiello
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
/ 75
(M10) (M12)
Tightening
torque (min)
(Nm)
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25