AUMA SA 25.1 Operating Instructions Manual page 93

SA 25.1 SA 48.1/SAR 25.1
AC 01.2 Non-Intrusive Modbus RTU
Please state device type and our order number (see name plate) when ordering spare parts. Only original AUMA spare parts should be used.
Failure to use original spare parts voids the warranty and exempts AUMA from any liability. Representation of spare parts may slightly vary
from actual delivery.
Ref. no. Designation
001.0 Housing
002.0 Bearing flange
003.0 Hollow shaft
005.0 Drive shaft
005.1 Motor coupling
005.2 Coupling pin
005.3 Manual drive coupling
005.4 Pull rope
006.0 Worm wheel
009.0 Manual gearing
017.0 Torque lever
018.0 Antriebsrad Drehmomentschaltung
019.0 Crown wheel
020.0 Swing lever
022.0 Drive pinion II for torque switching
023.0 Output drive wheel for limit switching
024.0 Drive wheel for limit switching
025.0 Locking plate
058.0 Cable for protective earth
070.0 Motor
080.0 Planetary gearing for motor drive (for A...
motor)
155.0 Reduction gearing
500.0 Cover
501.0 Socket carrier (complete with sockets)
502.0 Pin carrier without pins
503.0 Socket for controls
504.0 Socket for motor
505.0 Pin for controls
506.0 Pin for motor
507.0 Cover for electrical connection
511.0 Threaded plug
514.0 Output drive type A (without stem nut)
514.1 Axial needle roller bearing
514.2 Radial seal for output drive type A
535.1 Snap ring
539.0 Screw plug
SAR 30.1 Control unit: electronic (MWG)
Type
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Ref. no. Designation
542.0 Handwheel with ball handle
549.0 Output drive type B3/E/B4
549.1 Output drive sleeve B3/E/B4
551.1 Parallel key
553.0 Mechanical position indicator
556.0 Potentiometer as position transmitter
556.1 Potentiometer without slip clutch
557.0 Heater
558.0 Blinker transmitter including pins at wires
(without impulse disc and insulation plate)
559.0 1 Electromechanical control unit with
switches, including torque switching heads
559.0 2 Electronic control unit with magnetic limit
and torque transmitter (MWG)
560.0 1 Switch stack for direction OPEN
560.0-2 Switch stack for direction CLOSE
560.1 Switch for limit/torque
560.2 1 Switch case for direction OPEN
560.2-2 Switch case for direction CLOSE
566.0 RWG position transmitter
566.1 Potentiometer for RWG without slip clutch
566.2 Position transmitter board for RWG
566.3 Cable set for RWG
567.1 Slip clutch for potentiometer
568.1 Stem protection tube (without cap)
568.2 Protective cap for stem protection tube
568.3 V-seal
568.4 Threaded sleeve (for SA/SAR 25.1 and
30.1)
569.0 Change-over lever assy
569.1 Change-over lever
569.2 Notched pin
575.1 Stem nut (without thread)
602.0 Reduction frame
603.0 Motor connection
614.0 EWG position transmitter
627.0 MWG 05.03 cover
S1 Seal kit, small
S2 Seal kit, large
Spare parts
Type
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Set
Set
93