The Assignable Key Functions - Icom IC-705 Basic Manual

8
SET MODE

The assignable key functions

Function
--- No function
Push to increase the frequency (in 50 Hz
steps*), Memory channel, repeater, or
select the next station call sign.
UP
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
Push to decrease the frequency (in 50 Hz
steps), Memory channel, repeater, or select
the previous station call sign.
DOWN
* When the Tuning Step function is ON,
increases the frequency in the selected
Tuning Step.
Push to increase the frequency (in the
UP
selected Tuning Step), Memory channel,
(VFO: kHz)
repeater, or select the next station call sign.
Push to decrease the frequency (in the
DOWN selected Tuning Step), Memory channel,
(VFO: kHz) repeater, or select the previous station call
sign.
VOL UP Push to increase the volume level.
VOL DOWN Push to decrease the volume level.
XFC Hold down for 1 second to monitor signals.
CALL Push to select the Call channel mode.
• Push to select the VFO mode and the
Memory mode.
VFO/MEMO
• Hold down for 1 second to copy a
Memory channel contents to the VFO.
DR Push to turn the DR function ON or OFF.
FROM/TO In the DR screen
(DR) Push to select "FROM" or "TO."
Push to directly select the Home Channel
that is set to the selected mode (VFO/
Memory) or DR screen.
Home CH
L While in the Call channel mode, or
when no Home CH is set, an error beep
sounds.
In the VFO mode
• Push to increase an operating band.
BAND/
• Hold down for 1 second to recall the
GROUP
Band Stacking Register contents.
UP
In the Memory mode
Push to increase the Memory group.
In the VFO mode
• Push to decrease an operating band.
BAND/
• Hold down for 1 second to recall the
GROUP
Band Stacking Register contents.
DOWN
In the Memory mode
Push to decrease the Memory group.
• Push to start the previously selected
scan. While scanning, push to stop the
SCAN scan.
• Hold down for 1 second to open the
SCAN SELECT screen.
Description Function
Push to set the frequency to be skipped
Temporary while scanning.
Skip The selected frequencies are temporarily
skipped for faster scanning.
Push to announce the frequency, operating
mode, or call sign.
L In the VFO, Memory, or Call channel
mode, the frequency and the operating
SPEECH
mode are announced.
L In the DR screen, the call sign is
announced. If Simplex is selected, the
frequency is announced.
• Push to select the operating mode.
MODE • Hold down to toggle USB and LSB, CW
and CW-R, or RTTY and RTTY-R.
RF Power Push to adjust the transmit output power.
• Push to transmit the voice audio
recorded on the microSD card once.
Voice TX
• Hold down for 1 second to repeatedly
(T1)
transmit the voice audio.
L This key function can also be used on
the DR screen.
Voice TX
L If the voice audio is not saved in the
(T2)
Voice TX memory (T1 or T2), this
function is disabled.
• Push to transmit the Keyer memory
Keyer
contents once.
Memory
• Hold down for 1 second to repeatedly
(M1)
transmit the memory contents.
Keyer
L If the Keyer memory contents (M1
Memory
or M2) is not entered, this function is
(M2)
disabled.
Push to transmit a 1750 Hz Tone.
T-CALL
(Only for European version.)
• Push to display the RX History list.
• Hold down for 1 second to set the
RX>CS
last calling station's call sign to "TO"
(destination).
• Push to turn the Tuning Step function ON
or OFF.
TS
• Hold down for 1 second to open the TS
screen.
• Push to sequentially call up the contents
in the Memo Pads.
MPAD
• Hold down for 1 second to save the
displayed contents into the Memo Pad.
• Push to turn the Split function ON or
OFF.
SPLIT
• Hold down 1 second to turn ON the
Quick Split function.
• Push to select the VFO A or VFO B.
• Hold down for 1 second to set the
A/B
displayed VFO's frequency to the VFO
that is not displayed.
8-7
Description