Page 1
www.r6-ru4montesecchieta.it IZ5CCV SERVICE MANUAL HF/VHF/UHF ALL MODE TRANSCEIVER S-14214HZ-C1 Dec. 2005...
Page 2
8. READ the instructions of test equipment thoroughly before connecting equipment to the transceiver. Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
SECTION 2 INSIDE VIEWS • TOP VIEW LOGIC UNIT LOGIC UNIT LOGIC UNIT MAIN UNIT MAIN UNIT MAIN UNIT DDS UNIT DDS UNIT DDS UNIT (IC1302: HD64F2377VFQ33V) (IC1302: HD64F2377VFQ33V) (IC1302: HD64F2377VFQ33V) 1st Lo DDS 1st Lo DDS 1st Lo DDS (IC301*: AD9951YSV) (IC301*: AD9951YSV) (IC301*: AD9951YSV)
SECTION 3 CIRCUIT DESCRIPTION 3-1 RECEIVER CIRCUITS • Used RF high-pass fi lter (MAIN unit) 3-1-1 HF/50 MHz RF CIRCUIT (MAIN AND PA UNITS) Frequency Control Entrance Frequency Control Entrance The HF/50 MHz RF filters pass only the desired band sig- (MHz) signal diode...
Page 7
The amplified signals are passed through the band switch 3-1-5 1ST IF CIRCUIT (MAIN UNIT) (D461) and then applied to the 1st mixer circuit (MAIN unit) The 1st IF circuit filters and amplifies the 1st IF signal. via J101 (MAIN unit). •...
Page 8
The amplified IF signal is passed through the bandpass filter 3-1-11 DSP CIRCUIT (LOGIC UNIT) (FI1402) and then applied to the WFM demodulator circuit The DSP (Digital Signal Processor) circuit enables digital IF (IC1401). filter, manual notch, digital twin PBT and phase demodula- tion, etc.
3-1-13 AGC CIRCUIT (MAIN UNIT) 3-2 TRANSMITTER CIRCUITS The AGC (Automatic Gain Control) circuit adjusts IF amplify 3-2-1 MICROPHONE AMPLIFIER CIRCUIT (MAIN UNIT) gain to keep the audio output at a constant level. The The microphone amplifier circuit amplifies microphone audio receiver gain is determined by the voltage on the AGC line signal to a level needed for the DSP circuit.
Page 10
3-2-5 2ND MIXER CIRCUIT (MAIN UNIT) 3-2-8 RF CIRCUIT (MAIN UNIT) The 2nd mixer circuit mixes the 2nd IF signal with the 2nd The RF circuit amplifies and filters the RF signal from the LO signal to convert into the 1st IF frequency. 1st mixer circuit.
Page 11
3-2-9 DRIVE AND POWER AMPLIFIER CIRCUITS The VHF and UHF RF power amplified signal from the power amplifiers (PA unit; Q401, Q501) are detected at the (PA AND DRIVER UNITS) APC detectors (PA unit; D401, D404, D501, D504) respec- The drive and power amplifier circuits amplify the RF signal tively.
The VHF/UHF APC detector circuits (PA unit; D501, D504, 3-3 DDS CIRCUITS D401, D404) detect the forward and reflection signals and 3-3-1 GENERAL convert into DC voltages. The converted DC voltages are The DDS unit generates a 1st LO (124.517–594.487 MHz), combined and applied to the ALC amplifier (pins 1, 2) as a 2nd LO (124.032 MHz) and a 3rd LO (438.85 kHz) fre- "VUFOR"...
3-3-3 2ND LO AND REFERENCE OSCILLATOR 3-4 LOGIC CIRCUITS CIRCUITS (DDS UNIT) 3-4-1 BAND SELECTION DATA The reference oscillator (X1, Q1) generates a 24.8064 MHz IC2151 IC2152 frequency used for the 1st LO, 3rd LO and DSP circuits as a (MAIN) (MAIN) IC901...
3-5-2 MAIN UNIT VOLTAGE LINE Line Description Port Description number name Common 3.3 V converted from the 5 V line Outputs data signal for the LCD driver by the 3.3 V regulator circuit (IC1801). The 3.3 V (IC506). output voltage is applied to the D/A convert- er ICs (IC2151–IC5155), etc.
High: While transmitting the 430 MHz band. Outputs R8 regulator (Q1701, Q1702) control signal. Low : While receiving. Outputs T8 regulator (Q1703, Q1704) control signal. Low :While transmitting. Outputs the power control signal . POWS High :When IC-7000 is power ON. 3 - 10...
SECTION 4 ADJUSTMENT PROCEDURES 4-1 PREPARATION Some adjustment must be performed on the adjustment mode. M REQUIRED TEST EQUIPMENT EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RENGE Output voltage : 13.8 V DC Frequency range : 1 kHz ±10 % DC power supply Distortion meter Current capacity...
Page 17
• CONNECTION • Microphone connector (Rear panel view) NOTE! Connect the test equipment to the micropho0ne connector on the rear panel, otherwise the transmitter adjustment will not millivoltmeter adjusted properly. to [EXT SP] – Speaker Audio generator to [MIC] Pin 5 MIC GND Pin 6 –...
4-2 DDS ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION REFERENCE 1 • Enter the adjustment mode. FREQUENCY • Push [F1 (REF)]. 2 • Disconnect P4 from J801 (MAIN Connect a frequency counter to P4 and REF OSC unit). set 124.032000 MHz using [DIAL]. Then •...
Page 19
• MAIN UNIT Rear panel view J2231 Ammeter Display adjustment presetting DC power supply J801 Reference frequency check point • FRONT UNIT 0.0047µF 1kΩ Frequency counter CP536 Display check point C536 Display adjustment point R541 Display adjustment point CP505 Display check point 4 - 4...
Page 20
4-4 TRANSMITTER ADJUSTMENT (continue) MEASUREMENT ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST 1 • Operating freq : 10.10000 MHz REAR Connect an RF power 80 W Audio Output DETECTOR • MODE : USB panel meter to [ANT1] connec- genera- level •...
Page 21
• MAIN UNIT CP1601 SWR DETECTOR preset point L904 TX peak adjustment point L701 R1618 L604 TX peak adjustment point L612 • PA UNIT CP961 SWR DETECTOR check point C964 SWR DETECTOR adjustment point 4 - 6...
Page 22
4-4 TRANSMITTER ADJUSTMENT (Continue) ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION TX OUTPUT 1 • Connect an RF power meter to Po Min(HF) Set the output power to 1 W using [DIAL]. POWER (HF) [ANT1] connector. Then push [F-4 (SET)] . • Connect an audio generator to Set the output power to 10 W using Po Tune(HF) [MIC] connector and set as;...
Page 23
4-4 TRANSMITTER ADJUSTMENT (continue) ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION TX OUTPUT 1 • Connect an RF power to [ANT2] Po Min(144 M) Set the output power to 1 W using [DIAL]. POWER connector. Then push [F-4 (SET)]. (144 MHz) • Connect an audio generator to Set the output power to 12.5 W using Po 25%(144 M) [MIC] connector and set as;...
Page 24
4-4 TRANSMITTER ADJUSTMENT (continue) ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION 1 • Connect an RF power meter to Push [F-4 (SET)]. [ANT1] connector. • Connect an audio generator to [MIC] connector and set as; Level : 1.5 kHz/30 mV • Transmitting Drive Min 1 •...
Page 25
• MAIN UNIT CP1601 ID APC preset point Rear panel view Ammeter DC power supply L701 R1618 ID APC adjustment point Residual AM adjustment point 4 - 10...
4-5 RECEIVER ADJUSTMENT MEASUREMENT ADJUSTMENT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST RX PEAK 1 • Operating freq : 14.15000 MHz REAR C o n n e c t Maximum AF MAIN L702, (HF/50 MHz) • MODE : USB panel millivoltmeter to [EXT output level...
Page 27
• MAIN UNIT L703 RX peak adjustment point L702 4 - 12...
Page 28
4-5 RECEIVER ADJUSTMENT (continue) ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION RECEIVE 6 • Set an SSG as ; Tuned BPF(170 M) Push [F-4 (SET)]. SENSITIVITY Frequency : 169.8015 MHz (VHF/UHF) • Receiving 7 • Set an SSG as ; Tuned BPF(400 M) Push [F-4 (SET)].
Page 29
• MAIN UNIT C1423 WFM distortion adjustment point 4 - 14...
SECTION 5 PARTS LIST [DISPLAY UNIT] [REPLACEMENT UNITS] ORDER ORDER NO. UNIT NAME DESCRIPTION LOCATION 0324270102 U 7000 #02 FRONT [EUR], [FRA], [ESP], [EXP], [UK] 6190001561 S.COL CDRH5D18NP-101NC 68.4/6.3 0324270105 U 7000 #05 FRONT [USA] 6190001561 S.COL CDRH5D18NP-101NC 34.6/5.2 6200002041 S.COL NLV25T-101J 30.7/10.4 6190001561...
Page 31
[DISPLAY UNIT] [DISPLAY UNIT] ORDER ORDER DESCRIPTION DESCRIPTION LOCATION LOCATION R539 7030005720 S.RES ERJ2GEJ 563 X (56 kΩ) 69.6/29 R2028 7030005240 S.RES ERJ2GEJ 473 X (47 kΩ) 98.9/42.8 R540 7030010040 S.RES ERJ2GEJ-JPW 68.6/29 R2029 7030005240 S.RES ERJ2GEJ 473 X (47 kΩ) 73.5/16.9 S.RES ERJ2GEJ 151 X (150 Ω) R541...
SECTION 8 BOARD LAYOUTS 8-1 DISPLAY UNIT • TOP VIEW H100 H105 H110 H115 H120 H125 H130 H135 H140 H145 H150 H155 H160 8-2 VR UNIT • TOP VIEW to DISPLAY unit J401 8 - 1...
Page 64
• BOTTOM VIEW (DISPLAY UNIT) J601 STH1 to CONNECT unit MP1 CLK1 CLK2 CLK3 BLUE GREEN J202 3R3K STH2 MDBK MDAK -VIDEO VCOM YGND VGON to FRONT EP1 LRXD STV2 LTXD J303 C2016 F8VM MICE STV1 MICLE VGOFF MICL to FRONT DS1 (LCD) SQLS to FRONT W2...
Page 65
8-3 MAIN UNIT • TOP VIEW J2003 U/DM MAFM SENM MCEM MICM SQSM to Microphone J2002 MICE LRXD LTXD J2601 to CONNECT unit J1 ESPE ISPO J2005 to CHASSIS SP1 FDAT PRES J2231 HFOR YGND 3R3V HREF YY-VIDEO P2R8 to CONNECT P4R8 unit W1 AT13...
Page 67
8-4 PA UNIT • TOP VIEW V140 V135 V130 V125 V120 V115 V110 V105 W701 V100 DC 13.8V Q988 P401 to MAIN unit J101 P101 to MAIN unit J1 to MAIN unit J2004 J980 H100 H105 H110 H115 H120 H125 H130 H135 H140...
Page 68
• BOTTOM VIEW (PA UNIT) V140 V135 V130 V125 V120 V115 C528 V110 V105 V100 DRIVO from DRIVER unit J102 DRIVI from DRIVER unit J101 from DRIVER unit J104 from DRIVER unit J103 H155 H150 H145 H140 H135 H130 H125 H120 H115 H110...
Page 69
8-5 DDS UNIT • TOP VIEW MP1101 BANA GNDA KEYA ALCA FSKA SEND2 SQLA SEND1 MODA 14VA BDTA MP453 AFOD PTTD DIND SQLD DOTD J952 J951 J1001 to MAIN unit J2406 to MAIN unit J2405 to CHASSIS W11 (TUNER) 8 - 7...
8-7 CONNECT UNIT 8-9 HM-151 • TOP VIEW • TOP VIEW SPCH TUNER /LOCK /CALL DOWN to MAIN unit J2002 to MAIN unit J2231 MODE 8-8 DRIVER UNIT to PA unit to PA unit • TOP VIEW J102 J104 GENE F-INP (CE) J107...
Page 74
• BOTTOM VIEW (HM-151) • BOTTOM VIEW (CONNECT UNIT) MICE LTXD LRXD YGND YY-VIDEO • BOTTOM VIEW (DRIVER UNIT) to the IC-7000 MAIN unit J2003 8 - 12...
Page 75
SECTION 9 WIRING DIAGRAM HF/50 MHz PA UNIT 144/430 MHz DRIVER UNIT J101 DRIVI DRIVI DRIVI DRIVI DRIVI DRIVI DRIVI DRIVI J451 J101 J102 DC13.8V DRIVO DRIVO DRIVO DRIVO DRIVO DRIVO DRIVO DRIVO J101 FRONT UNIT J2003 VR UNIT J401 U/DM MAFM PBTK...
Page 77
SECTION 11 CIRCUIT DIAGRAMS 11-1 DISPLAY/ VR/ CONNECT UNITS DISPLAY UNIT (1) L3 100µ J202 3R3K 3R3V 3R3V MDBK R202 MDBK MAIN MDAK MDAK R201 DIAL 100µ MA729 FRONT UNIT 3R3V MA2SD1000L 100µ RSQ035P03TR CP2003 E7_7 R2020 1.2k FZMD XC9504B092ARN E7_1 RSR025N03 E7_5...
Page 78
DISPLAY UNIT (2) L703 100µ 3R3V 3R3V L507 R533 10µ C524 150p C526 0.0082 R529 10k R553 0 R532 10k C540 4.7 R541 5k R528 0 R544 C528 R530 82k R534 R547 470p R546 R548 E x p la n a to ry n o te s R521 C515...
Page 79
11-2 MAIN UNIT MAIN UNIT (1) BUS LINE1 P2T8 EP1953 C7 0.1 IC1952 BA033FP L1954 EP1952 C40 470p 100µ L1953 100µ Q1960 R2003 0 RSQ035P03TR R1952 L1951 0.15 100µ from PA unit J101 MA77 R1953 µPC2709T C15 0.001 0.001 0.5p 0.5p 1SV307 0.15...
Need help?
Do you have a question about the IC-7000 and is the answer not in the manual?
Questions and answers