Basler DGC-2020ES Configuration Instruction Manual page 16

2-4
DPF REGENRATE SETUP (Visible when ECU is configured for Standard, Volvo Penta, MTU
■
ADEC, GM/Doosan, Cummins, or MTU Smart Connect.)
BATT CHARGER SETUP
■
BATT CHARGR PREALARMS
■
SENS CHARGR PREALARMS
■
SPEED SELECT (Visible when ECU is configured for Volvo Penta.)
■
ACCEL POSITION (Visible when ECU is configured for Volvo Penta.)
■
MODULE TYPE (Visible when ECU is configured for MTU MDEC or MTU ECU7/ECU8.)
■
ALIVE MSG (Visible when ECU is configured for MTU MDEC or MTU ECU7/ECU8.)
■
SPEED SETUP
■
ECU SETUP (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
■
ECU7/ECU8, or MTU Smart Connect.)
Configuration through the Front Panel
DPF MANUAL REGEN
□
DPF REGEN DISABLE
□
CHARGER 1 TYPE
□
CHARGER 2 TYPE
□
CH1 COMMS FAIL
□
CH1 BATTERY FAIL
□
CH1 CHARGER FAIL
□
CH1 AC OFF
□
CH2 COMMS FAIL
□
CH2 BATTERY FAIL
□
CH2 CHARGER FAIL
□
CH2 AC OFF
□
CH1 THERMAL LIMIT (Visible when CHARGER 1 TYPE is set to SENS)
□
CH1 HI DC VOLTS (Visible when CHARGER 1 TYPE is set to SENS)
□
CH1 LOW DC VOLTS (Visible when CHARGER 1 TYPE is set to SENS)
□
CH1 LO CRANK V (Visible when CHARGER 1 TYPE is set to SENS)
□
CH1 INVLD SETTINGS (Visible when CHARGER 1 TYPE is set to SENS)
□
CH1 SNGL UNIT FL (Visible when CHARGER 1 TYPE is set to SENS)
□
CH2 THERMAL LIMIT (Visible when CHARGER 2 TYPE is set to SENS)
□
CH2 HI DC VOLTS (Visible when CHARGER 2 TYPE is set to SENS)
□
CH2 LOW DC VOLTS (Visible when CHARGER 2 TYPE is set to SENS)
□
CH2 LO CRANK V (Visible when CHARGER 2 TYPE is set to SENS)
□
CH2 INVLD SETTINGS (Visible when CHARGER 2 TYPE is set to SENS)
□
CH2 SNGL UNIT FL (Visible when CHARGER 2 TYPE is set to SENS)
□
J1939 RPM ENABLE (Visible when ECU is configured for Standard, Volvo Penta,
□
MTU ADEC, GM/Doosan, Cummins, or MTU Smart Connect.)
ENGINE RPM
□
SAVE RPM ADJUSTS
□
RPM BAND WIDTH
□
IDLE RPM
□
RPM CHECKSUM
□
SPEED UP (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
□
ECU7/ECU8, or MTU Smart Connect.)
SPEED DN (Visible when ECU is configured for MTU ADEC, MTU MDEC 304, MTU
□
ECU7/ECU8, or MTU Smart Connect.)
TEST OVRSPEED (Visible when ECU is configured for MTU ADEC, MTU MDEC
□
304, MTU ECU7/ECU8, or MTU Smart Connect.)
SPD DMAND SRC (Visible when ECU is configured for MTU ADEC, MTU MDEC
□
304, MTU ECU7/ECU8, or MTU Smart Connect.)
IDLE REQUEST (Visible when ECU is configured for MTU MDEC 304, MTU
□
ECU7/ECU8, or MTU Smart Connect.)
INCREASE IDLE (Visible when ECU is configured for MTU MDEC 304, or MTU
□
ECU7/ECU8.)
TRIP RESET (Visible when ECU is configured for MTU MDEC 304, or MTU
□
ECU7/ECU8.)
INT OIL PRIME
□
GOV PRM SW (Visible when ECU is configured for MTU ADEC or MTU Smart
□
Connect.)
ENG STRT PRIME (Visible when ECU is configured for MTU MDEC 304, or MTU
□
ECU7/ECU8.)
FAN OVERRIDE (Visible when ECU is configured for MTU MDEC 304, or MTU
□
ECU7/ECU8.)
9469200995
DGC-2020ES