Sony HDCU5000 Operating Instructions Manual page 12

f UHD SDI A/B/C/D connectors (BNC-type)
The signal from the video camera is output as UHD (4K) SDI
signals. The C and D connectors can also be used as input
connectors.
For details on settings, contact a Sony service or sales
representative.
g SDI OUT (3G/HD/SD SDI output) 1/2/3/4 connectors
(BNC-type)
The signal from the video camera may be output as 3G
signals, HD-SDI signals, or SD-SDI signals. They can output
signals with superimposed text characters and markers.
For details on settings, contact a Sony service or sales
representative.
h SDI I/O (3G/HD SDI input/output) 1/2/3/4 connectors
(BNC-type)
These can be used as return video inputs, HD prompter
inputs, camera video signal outputs, and HD-TRUNK outputs.
Set them in NETWORK TRUNK on the <TRUNK/
PROMPTER> page of the MAINTENANCE menu according to
the application.
i SDI RET (3G/HD/SD SDI return video input) 1/2/3/4
connectors (BNC-type)
Four different 3G/HD/SD SDI return video input signals may
be received independently. The selection of RET 1 to 4 is
made by the return switch of the video camera. The aspect
ratio can also be selected for an SD signal.
The type of input signal on RET 1 to 4 may be set individually
using the setup menu, or using the MSU-1500 series Master
Setup Unit.
For details on the setup menu, contact a Sony service or sales
representative.
Refer also to the Master Setup Unit manual.
j Rear indicator
Displays calls and statuses.
k REFERENCE IN/OUT connectors (BNC-type)
Input an HD tri-level sync signal or SD reference signal (black
burst signal, or black burst signal with 10-field ID) to the
REFERENCE IN connector.
The input signal is output from the REFERENCE OUT
connector as-is (loop-through). If loop-through output is not
used, terminate the unused connector at 75 ohms.
l INPUT area
1 PROMPTER (tele-prompter input) 1/2 connectors
(BNC-type)
Input the prompter signal of 1 channel or 2 channels
depending on the setting of PROMPTER2/VBS-RET on the
<REAR I/F> page of the SYSTEM CONFIG menu and
PROMPTER CHANNEL MODE on the <TRUNK/
PROMPTER> page of the MAINTENANCE menu. When
PROMPTER/VBS-RET is set to DISABLE, the input signal is
output from the other connector as-is (loop-through). If loop-
through output is not used, terminate the unused connector at
75 ohms. When PROMPTER/VBS-RET is set to ENABLE,
both connectors become inputs and they are terminated at
75 ohms inside the unit.
If the signal used is a 1.0 Vp-p, 75-ohm analog signal, it may
be output from the PROMPTER OUT connector of the video
camera with a frequency bandwidth of 5 MHz, regardless of
signal format.
Note
In the case of the HDC5500, connect to the PROMPTER1
connector. It is not supported by the PROMPTER2 connector.
2 VBS-RET (VBS return video input) connector*
(BNC-type)
A single VBS return video signal can be input independently.
* This connector doubles as the PROMPTER 2 connector.
The RET selection is made by the return switch of the video
camera. The type of input signal on each RET connector may
be set individually using the setup menu, or using the
MSU-1000 series Master Setup Unit. The aspect ratio may
also be selected for SD signals.
For details on setup menu operations, contact a Sony service
or sales representative.
Refer also to the Master Setup Unit manual.
For details on how to select the signal, contact a Sony service
or sales representative.
m CAMERA FIBER connector for HDC5000/5500
Used to connect a video camera, using an optical fiber cable.
All video camera signals, including power supply, control,
video, and audio, are sent and received over one optical fiber
cable.
Note
Dust on the connection surface of the optical fiber cable may
result in transmission errors. When not connected, always
cover the end of the connector with the supplied cap.
n TRUNK connector (round 12-pin)
Used to connect to the CCU connector on a camera via an
RS-232C or RS-422A interface. Communication with up to two
channels is available.
o Option kit mounting port
The optional HKCU-SM50 Single Mode Fiber Connector Kit
can be installed.
For an overview of option kits, see "Option Kits" (page 15).
p INTERCOM/TALLY/IO (intercom / tally / input/output)
connector (D-sub 50-pin)
Used to input and output intercom, tally, and program audio
signals. Connect to the intercom/tally/program audio
connector of the intercom system.
REAR PREVIEW function: Pin 35 is assigned for the output
pin of the REAR PREVIEW function.
q RCP/CNU connector (round 8-pin)
Used to connect to an MSU-1000 series Master Setup Unit,
CNU-700 Camera Command Network Unit, or RCP-3000/
1000 series Remote Control Panel via a CCA-5 connection
cable. Control signals are sent and received via this
connector. When using an RCP-3000/1000 series unit, power
is also supplied.
12