Page 1
HD CAMERA CONTROL UNIT HDCU2500 3G/HD SDI OUTPUT EXPANSION UNIT MULTI INTERFACE UNIT HKCU2007 HKCU1003 SD ENCODER UNIT HKCU1001 MAINTENANCE MANUAL 1st Edition...
Page 2
électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. Model Name Serial No. HDCU2500 (SY) 10001 and Higher HDCU2500 (CE) 40001 and Higher 安全のために,周辺機器を接続する際は,過大電圧を...
Page 3
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION The use of optical instruments with this product will increase eye hazard. The HDCU2500 is classified as a CLASS 1 LASER PRODUCT. HDCU2500...
Page 4
Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. HDCU2500...
Page 5
For the operating temperature of the equipment, refer to the specifications of the Operation Manual. 6. When performing the installation, keep the space away from walls in order to obtain proper exhaust and radiation of heat. HDCU2500...
Page 7
Connector Input/Output Signals of HDCU2500........
Page 11
Board Parts Location........................9-25 HDCU2500...
Page 13
Related manuals The following manuals are available in this model. If this manual is required, please contact your local Sony Sales Office/Service Center. • Operation Manual (Supplied with this unit) This manual is necessary for application and operation of this unit.
Page 15
If the ROM and software version is lower than the specified below, be sure to perform ROM replacement and updating the software. If ROM replacement and updating the software are required, contact your local Sony Sales Office/Service Center. 1-1-1.
Page 16
1-2. Power Cord To get a power cord, please contact your local Sony Sales Office/Service Center. WARNING • Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
Page 18
TRD 3 (+) Transmitted/Received Data 3 (+) POWER (+) RCP POWER, +30 V TRD 3 (–) Transmitted/Received Data 3 (–) POWER (–) GND for POWER VIDEO (X) 75 Ω, 1.0 V p-p 15. TRUNK A 12-pin, Female - External View - HDCU2500...
Page 19
MIC GAIN CONT” ON/OFF IN — GND for +5.5 V TALLY OUT R/G/Y TALLY OUT ON (GND) : Max. 30 mA IN Y TALLY OUT ON (GND) : Max. 30 mA IN ASPECT RE- L : REMOTE MOTE Continued HDCU2500...
Page 20
PGM1 (X) IN –20 dBu/0 dBu/+4 • BNC type PGM1 (Y) IN • VBS 1.0 V p-p, 75 Ω (Selectable with PGM1 (G) IN CCU Menu) — GND for AUX 2. PIX OUT AUX3 — — • BNC type Continued HDCU2500...
Page 21
HKCU1003 VDA-64C board Note Output Signals The VDA-64C board that adds the component video signal output function cannot be installed in HDCU2500. 1. VBS OUT • BNC type • VBS 1.0 V p-p, 75 Ω VDA-64A board 2. R/R-Y OUT Output Signals •...
Page 22
HKCU1003 Note HDCU2500 The VDA-64C board that adds the component video signal output Connector Name Connector/Cable function cannot be installed in HDCU2500. ® ® CAMERA (LEMO LEMO PUW. 3K. 93C. TLCC96...
Page 23
It is recommended to clean the optical contact portions mentioned below before connecting this unit to the camera. For details on a cleaning method, refer to“1-14. Cleaning of Connector/Cable”. • CAMERA connector of this unit • CCU connector of the camera • Optical/Electrical cable HDCU2500...
Page 25
1-5. Outside Dimensions HD CAMERA CONTROL UNIT Unit: mm 1-11 HDCU2500...
Page 26
Lit when the operation clock frequency of SG is 74.17582 — MHz. (When the frame frequency of the video signal is integer 1/1.001.) D108 90H (LINE Yellow Lit when the SD signal delay time at down-conversion is set — DELAY) to LINE-DELAY. 1-12 HDCU2500...
Page 27
Lit when the Main output is 1080-30PsF/29.97PsF. D209 Green — Lit when the Main output is 1080-25PsF. D210 Green — Lit when the Main output is 1080-24PsF/23.98PsF. DTX-9 Board D103 DTX-9 Board (Side A) Blinks when the format setting is not correct. 1-13 HDCU2500...
Page 28
Lit when the Main output is 1080-50i or 720-50P. D208 Green — Lit when the Main output is 1080-30PsF/29.97PsF. D209 Green — Lit when the Main output is 1080-25PsF. D210 Green — Lit when the Main output is 1080-24PsF/23.98PsF. Blinks when the format setting is defective. 1-14 HDCU2500...
Page 29
–: NPN open collector output S412 SYNC — Factory use S413 10F-BB — Factory use S416 Co-AX/D-S-F1 — Factory use Fiber S418 48V/50V/60V — Factory use S419 720/Psf/I — Factory use INTR S420 1001/RMT/1000 — Factory use REMOTE 1-15 HDCU2500...
Page 30
Forcible LEGACY switch that allows 1:1 com- LEGACY/ NETWORK munication between CAM and CCU NETWORK S202 CAM POWER — Turns ON/OFF the CAMERA POWER. — DRX-9 Board DRX-9 Board (Side A) Note Do not change the setting of “Factory use” switch. 1-16 HDCU2500...
Page 31
ON: Keeps the characters and the markers of the SDI monitor output (3, 4) turned on. Note Settings are for each RC-105 board. 2 to 8 Factory use OFF (ALL) SDP-17 Board S900 S400 SDP-17 Board (Side A) 1-17 HDCU2500...
Page 32
AT-167A Board (Side A) Ref. No. Name Description RV701 27M FREQ Volume that adjusts the free-run frequency of 27M-VCO (X701). Must be readjusted when replacing X701. RV702 CK-DUTY Volume that adjusts the clock duty of the 74 MHz clock. 1-18 HDCU2500...
Page 33
Adjusts the video level of the R (R-Y) output. RV504 B-Y/B LEVEL Adjusts the video level of the B (B-Y) output. RV505 Y/G LEVEL Adjusts the video level of the G (Y) output. RV506 The EN-159A board does not have this function 1-19 HDCU2500...
Page 34
Tektronix 1780R or equivalent (for NTSC) Tektronix 1781R or equivalent (for PAL) SD signal generator Tektronix TSG170A or equivalent (for NTSC) Tektronix TSG271 or equivalent (for PAL) Audio oscillator Tektronix SG-5010 or equivalent Frequency counter Advantest TR5821AK or equivalent 1-20 HDCU2500...
Page 35
Push the lithium battery with an insulated stick to detach it from the battery case. AT-167A board Install the removed parts by reversing the steps of removal. Set DATE/TIME in the DATE (C15) of the CCU CONFIGURATION menu. (Refer to“3. Menu Settings”.) 1-21 HDCU2500...
Page 36
Slide or lift up the portion A in the direction of the arrow and securely insert the flexible card wire into the deep end of the connector. Return the portion A to its original position and lock the connector. 1-22 HDCU2500...
Page 37
3: EN-159A 3: VDA-64A 1: Standard DRX-9 1: Standard HIF-62 HKCU1003 2: Standard RC-105 2: Standard HIF-26 3: EN-159B 3: VDA-64A 1: Standard DRX-9 1: Standard HIF-62 HKCU1003 2: Standard RC-105 2: Standard HIF-26 3: EN-159B 3: VDA-64B 1-23 HDCU2500...
Page 38
• Put the board on the groove at the bottom of the slot and then push it straight. • Check that the board is securely connected to the MB-1181 board. 1 2 3 Slot DRX-9 board (HKCU2007) Standard RC-105 board Close the front panel and secure it with two coin screws. 1-24 HDCU2500...
Page 39
• Put the board on the groove at the bottom of the slot and then push it straight. • Check that the board is securely connected to the MB-1181 board. B3 x 5 HIF-57 board (HKCU2007) B3 x 5 Standard HIF-26 board 1-25 HDCU2500...
Page 40
• Put the board on the groove at the bottom of the slot and then push it straight. • Check that the board is securely connected to the MB-1181 board. 1 2 3 Slot EN-159A board (HKCU1001) EN-159B board (HKCU1003) Close the front panel and secure it with two coin screws. 1-26 HDCU2500...
Page 41
• Put the board on the groove at the bottom of the slot and then push it straight. • Check that the board is securely connected to the MB-1181 board. B3 x 5 VDA-64A board (HKCU1001/1003) B3 x 5 VDA-64B board (HKCU1003) 1-27 HDCU2500...
Page 42
This unit uses the PLD (Programmable Logic Device) that supports the e-Production (EPR) system to write and rewrite the internal data. If the parts listed below needs to be replaced or if PLD needs to be upgraded, contact your local Sony Sales Office/ Service Center.
Page 43
PLD Download Tool software is available. Prepare the Project file. Note Download the Project file from the Sony Database Server. Turn off the power of this unit. Extend the board on which the PLD data is to be written or rewritten using the extension board.
Page 44
The fuse is critical parts to safe operation. Replace the components with Sony parts whose part number appear in the manual published by Sony. If the components are replaced by any parts other than the specified ones, this may cause a fire or electric shock.
Page 45
D1 (Side B) VIF-52 THP1 A2 (Side B) 1-804-458-21 THP2 A2 (Side B) THP3 C1 (Side B) 1-803-615-21 THP4 A2 (Side B) THP5 A2 (Side B) THP6 A1 (Side A) 1-804-458-21 Continued 1-31 HDCU2500...
Page 46
B4 (Side A) 1-533-817-21 THP2 C4 (Side A) THP3 H4 (Side A) THP4 J1 (Side A) THP5 H5 (Side A) THP6 H4 (Side A) 1-803-615-21 THP7 H4 (Side A) 1-32 HDCU2500...
Page 47
Optical contacts (white) [Female connector] Insert the optical connector cleaner straight. Ensure that it is held straight when inserting. Apply sufficient pressure (approximately 600 g to 700 g) to ensure that the optical contact is a little depressed. 1-33 HDCU2500...
Page 48
Clean the LEMO connectors and cables using the following procedure. Tools required • Alignment sleeve remover HC-001 (for female connector) Sony Part No,: J-6480-010-A or DCC.91.312.5LA or manufactured by LEMO, or equivalent Note Insert the shorter nose end when removing/installing the alignment sleeve. Grasp not the shock absorber portion of the remover but the handle in use.
Page 49
The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve. (Alignment sleeve: Sony P/N 9-980-074-01) Clean the tip of the white optical contacts with a cotton swab moistened with alcohol.
Page 50
Match the positioning marks of the adapter and the connector, and then push the adapter into the connector. Note Push the adapter until the confirmation groove comes in sight as shown in the figure. Confirmation groove Positioning marks Adapter 1-36 HDCU2500...
Page 51
Tighten the adapter pin clockwise until you feel that it is fixed to some extent. Note Do not fully tighten the adapter pin. [LC type connector] Clean the tip of the white optical contacts with a cotton swab moistened with alcohol. Optical contact (white) Optical contact (white) 1-37 HDCU2500...
Page 52
• Down-conversion function as necessary • Has the built-in 3G/HD signal color bar generator and supports multiple formats • Matches the MIC signal from the camera to the delay of the video signal, and then multiplexes it to the SDI signal. 1-38 HDCU2500...
Page 53
The HIF-62 board has the co-axial connector for outputting the 3G-SDI/HD-SD signals to external devices. The board outputs two systems of the main-line system 3G-SDI/HD-SD signal sent from the DRX-9 board, and outputs one system of the monitor-system 3G-SDI/HD-SD signal. SDI-99 board The SDI-99 board inputs the return signals from external devices. 1-39 HDCU2500...
Page 54
SD analog composite signals (VBS, PIX, and WFM signals). The board is equipped with the external synchronous circuit of the reference SC (sub carrier) of SD, and the composite signal whose external SC is locked can be output. There also is a through-path of the 8:4:4 component digital signal to the EN-159B board. 1-40 HDCU2500...
Page 55
The VDA-64B board is used to output the SD analog signals (PIX, WFM signals), and to input or output Frame_ Reference to external devices. Insert this board to the rear side of the slot that has the EN-159B board inserted in its front side. The VDA-64A and 64B boards cannot be inserted simultaneously. 1-41 HDCU2500...
Page 56
• The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-42 HDCU2500...
Page 57
Frame reference input/output VDA-64B • Component video signal output VDA-64C HKCU2007 • 3G-SDI/HD-SDI Output DRX-9 HIF-57 3G/HD SDI OUTPUT EX- PANSION UNIT Note *1: The VDA-64C board that adds the component video signal output function cannot be installed in HDCU2500. HDCU2500...
Page 58
2-1-1. Example of Connection SD Analog Monitor HD-SDI Video router LCD monitor HDC2400/2500 HDCU2500 HKCU1001 HKCU1003 HKCU2007 MSU-1000/1500 SD-SDI Monitor HDC2400/2500 HDCU2500 HKCU1001 HKCU1003 HKCU2007 HDC2400/2500 HDCU2500 HKCU1001 HKCU1003 HKCU2007 RCP-1000 Series HDC2400/2500 HDCU2500 HKCU1001 HD-SDI Monitor HKCU1003 HKCU2007 3G-SDI Monitor...
Page 59
HD/SD-SDI SIGNAL 3G/HD-SDI SIGNAL HD-SDI Monitor 3G-SDI Monitor HDCU2500 3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) HDC2400/2500 HD/SD-SDI SIGNAL 3G/HD-SDI SIGNAL HD-SDI Monitor 3G-SDI Monitor HDCU2500 Next HDCU2500 3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) HDCU2500...
Page 60
3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) 3G/HD-SDI SIGNAL HD/SD-SDI SIGNAL HDC2400/2500 ANALOG COMPOSITE VIDEO SIGNAL SD ANALOG Monitor VDA-A Waveform Monitor HD/SD-SDI Monitor HDCU2500 Next HDCU2500 3G-SDI Monitor 3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) HDCU2500...
Page 61
3G/HD-SDI SIGNAL HD/SD-SDI SIGNAL HD-SDI Monitor 3G-SDI Monitor HDCU2500 3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) HDC2400/2500 3G/HD-SDI SIGNAL HD/SD-SDI SIGNAL HD-SDI Monitor 3G-SDI Monitor HDCU2500 Next HDCU2500 3G/HD/SD-SDI, ANALOG RETURN SIGNAL SYNC OUT (HD or SD) HDCU2500...
Page 62
When the sub reference signal is not input, the pulse gate signal of the frame sync is output from the loop-through output terminal. The frame sequence between multiple CCUs can be locked if you connect this signal to the sub reference input of other CCUs. HDCU2500...
Page 63
While speaking to the headset microphone, adjust ENGINEER CANCEL LVL in INTERCOM (C07) of the CCU CONFIGURATION menu so that the voice heard from the headset becomes minimum. Reset the value of SIDE TONE in FRONT INCOM (C08) of the CCU CONFIGURATION menu to the previous value. HDCU2500...
Page 64
Selecting an Intercom LINE to be Connected to the INTERCOM Connector Select the intercom line to be connected to the INTERCOM connector on the front panel as follows with the INTERCOM switch. INTERCOM switch • When connecting to the producer line: Set the INTERCOM switch to PROD. HDCU2500...
Page 65
Microphone connector MIC IN CH-1 MIC IN CH-2 Set with CAM MIC GAIN of MIC/AUDIO (C05) Setting the microphone input gain of the video camera Pin No. Gain 60 dB 50 dB 40 dB 30 dB 20 dB HDCU2500...
Page 66
Setting MIC Output Level Set the MIC outputs (MIC1 and MIC2) with AUDIO OUT CH1 LEVEL/CH2 LEVEL in MIC/AUDIO (C06) of the CCU CONFIGURATION menu according to each signal level. –20 dBu, 0 dBu, or +4 dBu (Factory setting: 0 dB) 2-10 HDCU2500...
Page 67
(24 V/TTL). Set the TALLY INPUT (C16) of the CCU CONFIGURATION menu according to the tally system to be used. • Contact supply: CONTACT • 24 V supply: POWER (24V) • 5 V supply: POWER (TTL) 2-4-2. Camera Number Setting Set the camera number with OTHERS1 (C17) of the CCU CONFIGURATION menu. 2-11 HDCU2500...
Page 68
2-4-3. Connecting the Control, Intercom, Tally and Audio Signals HDCU2500 [1] INTERCOM/ TALLY/PGM INTERCOM/PROGRAM/ AUDIO/TALLY MIC OUT MIC OUTPUT MIC CONTROL and TALLY MIC REMOTE or WF REMOTE WF MONITOR CONTROL RCP/CNU HDCU2500 [2] INTERCOM/ TALLY/PGM INTERCOM/PROGRAM/ AUDIO/TALLY MIC OUT...
Page 69
SYSTEM OPERATION menu → GENLOCK PHASE (S02) → GENLOCK HD: HD tri-level sync SD: BB (black burst) signal When HD is selected Make coarse adjustment of the H phase by COARSE of GENLOCK PHASE (S02) and make fine adjustment by H STEP. 2-13 HDCU2500...
Page 70
Pin 13 Pin 14 Aspect ratio (ASPECT CTL CONT1) (ASPECT CTL CONT2) Squeeze (16 : 9) Edge crop (4 : 3) Set with S05:SD ASPECT of SYSTEM OPERATION menu Letterbox (4 : 3) 2-14 HDCU2500...
Page 71
Horizontal cutting position of 4 : 3 (12 : 9) Picture whose aspect ratio is converted (SD output) Edge-crop CROP POSITION can be changed. Squeeze The 16 : 9 ratio picture is output in the SD format without changing the ratio. 2-15 HDCU2500...
Page 72
Adjust the VBS signal level that is output from this unit using the color bar signal. Use the switch on the EN-159A/ 159B board (HKCU1001/1003) and the potentiometer on the panel of the unit to adjust the VBS signal level. 2-16 HDCU2500...
Page 73
Adjustment Procedure Using EN-159A/159B Board Press the BARS button of the MSU-1000/1500 or RCP-1500/1501. Press the ENC button of the WAVEFORM MONITOR button of M SU-1000/1500 or MONITOR SELECT button of RCP-1500/1501 to display color bars on the waveform monitor. 2-17 HDCU2500...
Page 74
The waveform monitor control signal of this unit is output in synchronization with the WF OUT connector output signal. Adjust the position of the signal to be displayed with potentiometer RV301 (STAIR STEP POSITION) on the EN-159A/159B board. 2-18 HDCU2500...
Page 75
Adjustment Procedure Using EN-159A/159B Board Press the BARS button of the MSU-1000/1500 or RCP-1500/1501. Press the ENC button of the WAVEFORM MONITOR button of M SU-1000/1500 or MONITOR SELECT button of RCP-1500/1501 to display color bars on the waveform monitor. 2-19 HDCU2500...
Page 76
Set the format of the return signal to be input to the RET1, RET2, and RET3 connector using the maintenance menu of MSU-1000/1500 or S07: RETURN SETUP in the SYSTEM OPERATION menu of this unit. Note When required, either of the PROMPTER connectors can be assigned for the fourth return video input (RET4), exclusively for analog VBS signals. 2-20 HDCU2500...
Page 77
Turn the DISP/MENU lever to the MENU side within two seconds. DISP/MENU lever CANCEL/ENTER lever CONTROL knob Check that the following screen appears. If it does not appear, repeat steps 1 to 3. ** CCU MENU ** → SYSTEM OPERATION CCU CONFIGURATION NETWORK SETTINGS VE OPERATION MAINTENANCE HDCU2500...
Page 78
Turn the DISP/MENU lever to the MENU. The menu disappears. To restart the setting operation, turn the DISP/MENU lever again to the MENU side. 3-1-3. Memory Stick The following types of Memory Stick are available for this unit. • Memory Stick • Memory Stick PRO (Up to 2 GB) HDCU2500...
Page 79
Detail of SD output CC Reduction: ON Coring: 0 Level : 35 SD Detail: ON Level : 0 Comb Limit : 0 Lim-w : Crisp : 0 Lim-b : LDKnee: 0 LDGain: Ratio : 0 Freq HDCU2500...
Page 80
CCU power supply fan status CAMERA Timer Elapsed time since power-on CCU POWER CCU power supply type and status Fan Power OK Serial No. CCU serial number Timer CCU Power AC OK SerialNo 00002002 HDCU2500...
Page 81
Connection speed setting status Connect Speed 100M Duplex Mode FULL Duplex Mode Communication method setting status MDI/MDIX Select : MDIX MDI/MDIX Select Communications port wiring configuration selection status Link Status Link Status LAN connection status HDCU2500...
Page 82
Status of power supply to the AT board Line Delay :Line(120H) PLD Version AT board PLD version Power Supply:OK PLD Version :3.00 Done VIF Power Status of power supply to the VIF board VIF Power HDCU2500...
Page 83
PLD version of the board installed in option slot 1 and the board name PLD Version:1.00 Done Rear, Power Status of power supply to the rear board and board name Rear :HIF Power:OK HDCU2500...
Page 84
PLD Version:1.00 Done Rear:VDA-A Power:OK 3-2-8. SDP Board Diagnostics Menu Image Item Description POWER Status of power supply to the SDP board *SDP Diag* 15/17 PLD Version SDP board PLD version Power:OK PLD Version:1.00 Done HDCU2500...
Page 85
ALL BOARD OK 3-2-10. Version Information of ROMs in Each Unit Menu Image Item Description ROM version of the camera connected to this unit *ROM Version* 17/17 ROM version of this unit HDC2000 1.00 11.12.20 HDCU2000 1.00 11.12.20 HDCU2500...
Page 86
0 to 7 Adjusts the reference signal lock phase. Vertical phase (in units of line) SUB-REF (NONE), (EXT IN) Displays whether sub-reference signal input is present. (Display only) (UNKNOWN), Sub-reference signal format display (Frame Gate), (HD), (Display only) (SD) 3-10 HDCU2500...
Page 87
HD signals. COMPONENT RGB, YCD Selects the component signal connector’s output format. When CCU VIDEO CONVERT is set to ENB, the CCU internal video conversion is delayed, so adjust the camera's signal by advancing it as necessary. 3-11 HDCU2500...
Page 89
Settings in ( ): Displayed when SQUEEZE or EDGE CROP is se- lected in SD ASPECT (Display on- H-INTERP A, B, C, D, E Selects the down converter horizon- tal filter. V-INTERP A, B, C, D, E Selects the down converter vertical filter. 3-13 HDCU2500...
Page 90
SD-RETURN LB LINE 360, 364 Set the effective line setting for MATRIX : LB LINE: 364 letterbox. ASPECT : MANUAL ASPECT MAN- Sets the auto-linking function for UAL/ this unit’s aspect setting. AUTO 3-14 HDCU2500...
Page 91
Switches the left and right sides when split- MODE ting the display. BORDER OFF, ON Selects whether or not to display the boun- LINE dary line when splitting the display. CHANNEL (OFF), (ON) Selects whether to display the Channel ID with this line’s output. 3-15 HDCU2500...
Page 92
Turns the signal for charac- ters superimposed on a col- or bar ON/OFF. GRAY ON, OFF ON: Gray screen output when camera power supply is off. OFF: Color bar signal out- put when camera power supply is off. 3-16 HDCU2500...
Page 93
ESC END Turn the CANCEL/ENTER lever to ENTER. The unit transitions to the character input mode and the cursor appears in the software keyboard field. Set the cursor to the character you want to input with the control knob. 3-17 HDCU2500...
Page 94
WHITE- 0.0 to Sets the PIX output bar character PIX CHARACTER LEVEL 107.0% level. WHITE-LEVEL : 75.0% BLACK 0.0 to Sets the PIX output bar character BLACK-LEVEL : 0.0% -LEVEL 107.0% border black level. 3-18 HDCU2500...
Page 95
MIC-REMOTE CHARA/ CHARACTER, Sets the output for the CHARACTER/ CHARA/SYNC: CHARACTER REAR PREVIEW: MOMENTARY SYNC SYNC SYNC connector. REAR PRE- MOMENTARY, Selects the REAR PREVIEW output oper- VIEW TOGGLE ating mode. 3-19 HDCU2500...
Page 96
(OFF): Displayed when 4WIRE is selected in SYSTEM I/F. (Display only) (Display only) CANCEL — Sets the side tone cancel level. PGM1 IN- –20, 0, +4 dBu Sets the PGM1 input level. PGM2 IN- –20, 0, +4 dBu Sets the PGM2 input level. 3-20 HDCU2500...
Page 97
PGM signal through the right. PGM SEL PGM1, PGM2, Sets the PGM level. PGM1 + PGM2 PGM1 LVL 0 to 99 Sets the PGM1 level. PGM2 LVL 0 to 99 Sets the PGM2 level. 3-21 HDCU2500...
Page 98
CABLE CAMERA CABLE, Sets the transmission format COAX between the camera and CCU. AUX REMOTE DISABLE, ENA- Sets whether to use AUX RE- MOTE. Note AES/EBU is not available when AUX REMOTE is set to ENABLE. 3-22 HDCU2500...
Page 99
CHROMA VBS LEVEL : LEVEL –99 to 99 Adjusts the PIX output video level. CHROMA: PIX LEVEL : CHROMA CHROMA: WFM LEVEL : LEVEL –99 to 99 Adjusts the WFM output video level. CHROMA: CHROMA 3-23 HDCU2500...
Page 100
ND FILTER Displays or hides the ND filter indication. CC FILTER Displays or hides the CC indication. IRIS Displays or hides the IRIS indication. EXTENDER Displays or hides the EXTENDER indica- tion. 3-24 HDCU2500...
Page 101
C15 TOP POWER (24 V), POWER (TTL) R-TALLY: POWER(24V) G-TALLY: POWER(24V) G-TALLY CONTACT, GREEN tally input setting Y-TALLY: POWER(24V) POWER (24 V), POWER (TTL) Y-TALLY CONTACT, YELLOW tally input setting POWER (24 V), POWER (TTL) 3-25 HDCU2500...
Page 102
Notes • When CAM MENU is set to ON, menu operation shifts to the cam- era menu side, disabling opera- tion of the CCU CONFIGURA- TION menu. • The camera menu is not displayed in the SD output. 3-26 HDCU2500...
Page 103
OFF is selected in AU- TO NEGOTIATION. MDI/MDIX SE- MDI, Selects the communica- LECT MDIX tion line. LINK CONDITION (DOWN), Displays connection sta- (UP) tus. (Display only) (DOWN): Connection failure (UP): Connection suc- cessful Determines changes in - the page. 3-27 HDCU2500...
Page 104
MCS mode. MASTER IP ADDRESS N04: NETWORK RESET Menu Image Item Settings Description ALL RSET Re-sets all settings in the NETWORK SET- - <NETWORK RESET> N04 TOP TINGS menu to factory settings. ALL RESET 3-28 HDCU2500...
Page 105
Item Description STORE FILE Registers the current adjustment values as an < O H B F I L E > V 0 3 T O P → OHB file. S T O R E F I L E 3-29 HDCU2500...
Page 106
F L A R E V M O D O N D . S H A D : O F F FLARE ON/OFF T E S T : O F F V MOD ON/OFF D.SHAD ON/OFF TEST OFF/1/2 3-30 HDCU2500...
Page 107
±99 A U T O K N E E : O F F ON/OFF P O I N T L I M I T : S L O P E AUTO KNEE OFF/AUTO POINT LIMIT ±99 SLOPE ±99 3-31 HDCU2500...
Page 108
L I M I T E R [ M ] : [WHT] ±99 [ W H T ] : [ B L K ] : C R I S P [BLK] ±99 L V L D E P CRISP ±99 LEVEL DEP ±99 ON/OFF 3-32 HDCU2500...
Page 109
S H U T T E R : O F F ECS FREQ : 1 / 1 0 0 E C S F R E Q : 6 0 . 0 0 H z ON/OFF E V S : O F F 3-33 HDCU2500...
Page 110
L I M I T E R [ M S T ] : [WHT] ±99 [ W H T ] : [ B L K ] : [BLK] ±99 C R I S P CRISP ±99 3-34 HDCU2500...
Page 111
M U L T I M A T R I X : O F F SATURATION ±99 Adjusts the SD multi-matrix correction value of saturation for each PHASE (16 angles). ALL PRESET MATRIX ON/OFF PRESET MATRIX ON/OFF MULTI MATRIX ON/OFF 3-35 HDCU2500...
Page 112
I R I S L E V E L : A P L R A T I O : I R I S G A I N : AUTO IRIS ON/OFF A U T O I R I S : O F F 3-36 HDCU2500...
Page 113
ABB:BREAK AUTO WHITE – AWB:EXECUTING AWB:OK AWB:NG AWB:BREAK AUTO LEVEL – LEVEL AUTO:EXE- LEVEL AU- LEVEL AUTO:NG LEVEL AU- CUTING TO:OK TO:BREAK AUTO WHITE – AWS:EXECUTING AWS:OK AWS:NG AWS:BREAK SHADING AUTO BLACK – ABS:EXECUTING ABS:OK ABS:NG ABS:BREAK SHADING 3-37 HDCU2500...
Page 114
M O N O C O L O R : O F F to 90 when the rotary encoder is rota- P H A S E S A T U R A T I O N : ted clockwise. SATURATION ±99 3-38 HDCU2500...
Page 115
EEPROM (IC101) on the AT-167A board. NAME HDCU2500 S E R I A L N O : 0 0 0 0 0 0 0 0 To modify the setup information, set N A M E : H D C U 2 5 0 0...
Page 116
P R O M P T E R 1 L E V E L : PROMPTER2 ±99 Prompter 2 signal level adjustment P R O M P T E R 2 L E V E L : LEVEL 3-40 HDCU2500...
Page 117
gain are common. • Pin 14 is forced LEGACY. STANDARD, STANDARD: Standard HDCU2500 HDCU2500: Same setting as HDCU2500 PNL ASPECT ENABLE, DIS- When MIC REMOTE is connected, ASPECT ABLE from the remote panel is operated. RCP PIX CTRL ENABLE, DIS- Control from RCP PIX is prioritized.
Page 119
Refer to “4-3-2. CN-3451 Board” CNB-29A Board Refer to “4-6-8. CNB-29A Board” (10) DRX-9 Board Refer to “4-5-1. Installing/Removing Plug-in Boards on the Front Side” (11) DTX-9 Board Refer to “4-5-1. Installing/Removing Plug-in Boards on the Front Side” Continued HDCU2500...
Page 120
“4-5-1. Installing/Removing Plug-in Boards on the Front Side” VDA-64A Board (HKCU1003) VDA-64B Board (HKCU1003) HIF-57 Board (HKCU2007) (23) EN-159A Board (HKCU1001) Refer to “4-5-2. Installing/Removing Plug-in Boards and Blank Panels DRX-9 Board (HKCU2007) on the Rear Side” EN-159B Board (HKCU1003) (16) (20) (18) (14) (15) HDCU2500...
Page 121
(13) (19) (21) (12) (23) (22) (11) (17) (10) 4-1-2. Basic Knowledge Flexible Card Wire When connecting flexible card wires, connect them firmly referring to “1-9. Replacing the Flexible Card Wires”. HDCU2500...
Page 122
Loosen the two coin screws, open the front panel, and then remove the cover. B3 x 5 Cover B3 x 5 B3 x 5 Front panel Coin screws Remove the two screws, and disconnect the harnesses from the connector on the power block assembly (D00). HDCU2500...
Page 123
DC Fan CAUTION If the fan is defective, the temperature inside HDCU2500 will rise. Touching the inside of the unit in this state may cause a burn. Replace the parts after the power is turned off and the inside is cooled.
Page 124
Label Install the DC fan by reversing steps 3 to 6. Note When installing the DC fan, carefully install it paying attention to the label location. Take in the slack of the DC fan harness at the harness clamp. HDCU2500...
Page 125
Remove the nine screws, and remove the cover (EK) in the arrow direction. Cover (EK) K3 x 6 K3 x 6 K3 x 6 K3 x 6 K3 x 6 K3 x 6 Disconnect the harnesses from the connectors CN601, CN6001 and CN6002 on the RE-274 board. HDCU2500...
Page 126
Remove the cover (EK). (Refer to “4-2-3. RE-274 Board”) Procedure Cut the tie band that bundles the harnesses. Disconnect the harnesses from the connectors CN105, CN1001, and CN1002 on the PS-778D00 board. Harnesses Tie band Harness CN1002 CN1001 CN105 Tie band HDCU2500...
Page 127
Remove the two screws to detach the front panel (E). Remove the soft shield A. Remove the two screws to detach the main chassis cover. Main chassis cover Front panel (E) K3 x 6 K3 x 6 Soft shield A K3 x 6 HDCU2500...
Page 128
Notes on Disassembling the Power Block Assembly (D00) After the power block assembly (D00) was disassembled and parts have been replaced or repaired, extend the harnesses and clamp them with harness clamps referring to the following three figures. 4-10 HDCU2500...
Page 129
Thermostat Harness and Harness (BOARD3) Harness Thermostat (BOARD3) harness 5 ± 2 mm Tie band Ferrite core Harness (BOARD1) and Harness (BOARD2) (Bottom Side) Tie band 30 ± 3 mm Harness (BOARD2) Harness (BOARD1) 4-11 HDCU2500...
Page 130
Harness (BOARD1) and Harness (BOARD2) (Upper Side) Harness (BOARD2) Harness (BOARD1) Lead pin RE-274 board 4-12 HDCU2500...
Page 131
Install the removed parts by reversing the steps of removal. 4-3-2. CN-3451 Board Preparation Open the front panel. (Refer to “4-3-1. Removal and Installation of Front Panel”) Procedure Disconnect the harness from the connector CN2 on the CN-3451 board. 4-13 HDCU2500...
Page 132
Disconnect the harness (INCOM1) from the connector CN4 on the AU-340 board. Flexible flat cable AU-340 board Harness (INCOM1) B3 x 5 PWB stopper Remove the four screws and the rotary encoder knob, and remove the AU-340 board. 4-14 HDCU2500...
Page 133
Disconnect the LE-377 board from the connector on the AU-340 board. Connector B3 x 5 B3 x 5 B3 x 5 LE-377 board Rotary encoder knob AU-340 board Install the removed parts by reversing the steps of removal. 4-15 HDCU2500...
Page 134
Remove the rear panel assembly. (Refer to “4-4-1. Removal and Installation of Rear Panel Assembly”) Procedure Remove the four screws, and remove the cover (SDP-17) and the fiber cable cover. Disconnect the harness from the connector CN200 on the SDP-17 board. 4-16 HDCU2500...
Page 135
Remove the two screws (B3 x 5) , and remove the SDP-17 shield plate from the rear panel. Remove the two spacers (A) and heat trans sheets (1) . 4-17 HDCU2500...
Page 136
When installing the SDP-17 board, arrange the optical cables as shown in the figure below. Pass the optical cables between chip parts. SDP-17 board Do not pass the optical cables over this part. Optical cables Pass the optical UL tape cables under the tab. 4-18 HDCU2500...
Page 137
To install the removed plug-in board, insert it along the guides of each slot and push it so that it is securely connected to the connector on the MB-1181 board. MB-1181 board Guides Plug-in board Close the front panel. 4-19 HDCU2500...
Page 138
To install the removed plug-in board, insert it along the guide of each slot and push it so that it is securely connected to the connector on the MB-1181 board. Install the two screws. Blank panel Plug-in board MB-1181 board Guide B3 x 5 B3 x 5 4-20 HDCU2500...
Page 139
Remove the three screws to detach the shield finger (BNC) and the HIF-62 board. Shield finger HIF-62 board B3 x 5 Install the removed parts by reversing the steps of removal. 4-6-2. SDI-99 Board Preparation Remove the rear panel assembly. (Refer to “4-4-1. Removal and Installation of Rear Panel Assembly”) 4-21 HDCU2500...
Page 140
Remove the SDI-99 board. (Refer to “4-6-2. SDI-99 Board”) Procedure Remove the two screws of the round type connector (8P). P2.6 x 5 Round type connector (8P) Disconnect the flexible flat cables from the connectors CN7 and CN10 on the CN-2675G board. 4-22 HDCU2500...
Page 141
“4-4-1. Removal and Installation of Rear Panel Assembly”) Remove the rear sub assembly (included in the HIF-62 board and the SDI-99 board) . (Refer to “4-6-1. HIF-62 Board”) Procedure Disconnect the harness (MIC) from the connector CN3 on the CN-2676 board. 4-23 HDCU2500...
Page 142
Remove the rear sub assembly (included in the HIF-62 board and the SDI-99 board). (Refer to “4-6-1. HIF-62 Board”) Procedure Disconnect the flexible flat cable from the connector CN2 on the CN-2677G board. CN-2677G board Flexible flat cable 4-24 HDCU2500...
Page 143
Remove the rear sub assembly (included in the HIF-62 board and the SDI-99 board) . (Refer to “4-6-1. HIF-62 Board”) Procedure Disconnect the flexible flat cable from the connector CN5 on the CNB-29A board. Disconnect the VIF-52 board from the connector on the MB-1181 board. MB-1181 board VIF-52 board CNB-29A board Flexible flat cable 4-25 HDCU2500...
Page 144
Remove the rear sub assembly (included in the HIF-62 board and the SDI-99 board) . (Refer to “4-6-1. HIF-62 Board”) Remove the VIF-52 board. (Refer to “4-6-6. VIF-52 Board”) Procedure Disconnect the flexible flat cable from the connector CN4 on the CNB-29A board. Disconnect the ADO-12 board from the connector on the MB-1181 board. 4-26 HDCU2500...
Page 145
Remove the VIF-52 board. (Refer to “4-6-6. VIF-52 Board”) Remove the ADO-12 board. (Refer to “4-6-7. ADO-12 Board”) Procedure Disconnect the flexible flat cable from the connector CN3 on the CNB-29A board. Remove the two screws, and remove the PWB guide (rear) . 4-27 HDCU2500...
Page 146
Remove the PWB guide (rear). (Refer to “4-6-8. CNB-29A Board”) Procedure Disconnect the harness from the connector CN31 on the MB-1181 board. Remove the four screws, and disconnect the flexible flat cable from the connector CN32 on the MB-1181 board. 4-28 HDCU2500...
Page 147
Remove the MB-1181 board. Flexible flat cable CN31 PSW3 x 6 CN32 Harness PSW3 x 6 MB-1181 board PSW3 x 6 Install the removed parts by reversing the steps of removal. 4-29 HDCU2500...
Page 149
• To adjust this unit, extend each plug-in board. Before pulling out the boards, be sure to turn off the main power. • Before starting adjustment, warm up for about 10 minutes. • Before using the MSU-1000/1500, check the version of the ROM. For details, refer to Section “1-1. Checking the ROM and Software Version ROM”. HDCU2500...
Page 150
5-1-3. Connection of Equipment Adjusting the HDCU2500 HD COLOR CAMERA HDC2500 HD CAMERA CONTROL UNIT Measuring HDCU2500 OPTICAL FIBER equipment CABLE MASTER SETUP UNIT MSU-1000/1500 CCA-5 CABLE (max. 200m) Adjusting the HKCU1001/1003 HD CAMERA CONTROL UNIT HDCU2500 SD ENCODER UNIT...
Page 151
AUTO KNEE button OFF (dark) SKIN DETAIL button OFF (dark) Others Name Setting GAMMA OFF button ON (dark) MASTER GAIN 0 (0 dB) FILTER button (ND) 1 (CLEAR) FILTER button (CC) B (3200 K) ON button (Shutter control block) OFF (dark) HDCU2500...
Page 152
Turn the INTERCOM switch on the front panel to PROD side . INTERCOM switch INTERCOM connector Input a sine wave (1 kHz, 220 mV p-p (–20 dBu)) to pin 2 (X), pin 1 (Y), and pin 3 (G) of the INTERCOM connector from the audio oscillator. Audio oscillator 600 Ω HDCU2500...
Page 153
Turn the INTERCOM switch on the front panel to ENG side . INTERCOM switch INTERCOM connector Input a sine wave (1 kHz, 220 mV p-p (–20 dBu)) to pin 2 (X), pin 1 (Y), and pin 3 (G) of the INTERCOM connector from the audio oscillator. Audio oscillator 600 Ω HDCU2500...
Page 154
Test Point: TP601 (B-4)/AVP-15 board Adjusting Point: CCU CONFIGURATION menu → INTERCOM (C07) → ENGINEER → CANCEL LVL Specification: B = Minimum TP601 AVP-15 board (Side A ) Setting after Adjustment After this adjustment is completed, set the switch to the previous state. HDCU2500...
Page 155
TP704 AT-167A board (Side A ) Setting after Adjustment After this adjustment is completed, set the switch to the previous state and reconnect the disconnected cable. 5-3-2. Clock (74 MHz) Duty Adjustment Measuring equipment Oscilloscope (20 MHz BWLimit: ON) HDCU2500...
Page 156
Measuring equipment • SD waveform monitor • SD signal generator Preparation • Extend the DTX-9 board using an extended board. • Connect the SD signal generator to the PROMPTER IN connector. NTSC: SMPTE color bar PAL: EBU color bar HDCU2500...
Page 157
This adjustment is used tentatively when a repair is made. This adjustment must be made again according to the waveform monitor characteristics at the system setup. Preparation Extend the EN-159A/159B board using an extended board. Adjustment Procedure Test Point: TP305 (E-3)/EN-159A/159B board Adjusting Point: HDCU2500...
Page 158
• A = 3.0 ±0.5 V p-p (RV302) • B = 0 ±0.5 V dc (RV301) TP305 RV302 RV301 EN-159A/159B board (Side A) Setting after Adjustment After this adjustment is completed, set the switch to the previous state. 5-10 HDCU2500...
Page 160
WF Output Level Adjustment Measuring equipment SD waveform monitor Preparation Extend the EN-159A/159B board using an extended board. Adjustment Procedure Test Point: WF OUT connector/VDA-64A board Adjusting Point: RV305 (F-4)/EN-159A/159B board Specification: A = 140 ±1 IRE (75 Ω termination) 5-12 HDCU2500...
Page 161
B = 1000 ±7 mVp-p (75 Ω termination) NTSC RV305 EN-159A/159B board (Side A) 5-13 HDCU2500...
Page 163
Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2. Standardization of Parts 2. 部品の共通化 Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は,セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.
Page 164
3-697-760-03 s SCREW,COIN (SY) 3-697-760-12 s SCREW,COIN (CE) 3-725-295-21 s SCREW, (+) (B3) 3-872-856-02 s COVER 3-872-865-01 s SHAFT,STEP 4-111-825-01 s SHIELD CUSION 4-139-232-01 s KNOB, ROTARY ENCODER 4-413-870-01 s SHEET,FRONT PANEL 4-413-871-01 s PANEL(P),INCOM 4-413-880-01 s DOUBLE STICK TAPE (PANEL) HDCU2500...
Page 165
A-1856-354-A s MOUNTED CIRCUIT BOARD, AVP-15 A-1856-355-A s MOUNTED CIRCUIT BOARD, DTX-9 A-1856-356-A s MOUNTED CIRCUIT BOARD, DRX-9 A-1856-357-A s MOUNTED CIRCUIT BOARD, RC-105 A-1859-145-A s MOUNTED CIRCUIT BOARD, AT-167A 1-528-174-72 s BATTERY, LITHIUM (CR2032 TYPE) 3-725-295-21 s SCREW, (+) (B3) HDCU2500...
Page 166
3-872-863-02 s FIBER CN HOLDER (LEMO) 3-986-571-01 s FIBER CN HOLDER (TAJIMI) 4-413-875-01 s REAR PANEL(P) 4-413-876-01 s REAR PANEL SHEET 4-669-854-01 s CAGE, TOP 7-623-925-11 s WASHER 4.0, NYLON 7-682-163-01 s SCREW +P 4X12 7-682-648-01 s SCREW +PS 3X8 HDCU2500...
Page 167
1-831-664-11 s CABLE, FLEXIBLE FLAT (50 CORE) 1-831-665-11 s CABLE, FLEXIBLE FLAT (45 CORE) 1-831-666-11 s CABLE, FLEXIBLE FLAT (15 CORE) 3-165-162-01 s SCREW (+P2.6X5) (TYPE1) 3-364-941-01 s SCREW (+B) (2.6X5), NYLOK 3-531-576-01 s RIVET 3-725-295-21 s SCREW, (+) (B3) HDCU2500...
Page 168
1-967-199-11 s HARNESS, SUB (TO SW) 1-967-200-12 s HARNESS, SUB (FROM AC) 2-990-241-02 s HOLDER (A), PLUG 4-191-661-01 s SHEET RADIATION (EK)-3(D00-T1) 4-382-854-51 s SCREW (M3X6), P, SW (+) 7-682-247-04 s SCREW +K 3X6 7-682-949-01 s SCREW +PSW 3X10 7-682-955-01 s SCREW +PSW 3X30 HDCU2500...
Page 169
1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216 C108 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C175 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C109 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C176 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 HDCU2500...
Page 170
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C351 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C718 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216 C352 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C719 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 HDCU2500...
Page 171
1-100-506-91 s CAP, CERAMIC 1MF C (1005) C784 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005 C861 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005 C785 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005 C862 1-165-989-91 s CAP, CERAMIC 10MF (2012) HDCU2500...
Page 172
IC307 8-759-471-91 s IC 74VHC04MTCX 1-535-877-22 s CHIP, CHECKER IC308 8-759-092-83 s IC SN75158PSR FB701 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC309 6-706-487-01 s IC TC7SH08FU FB702 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC401 6-713-799-01 s IC BU7122KV-E2 6-10 HDCU2500...
Page 173
1-414-398-41 s INDUCTOR (SMD) 10.0UH IC758 6-706-478-01 s IC TC7SET08FU 8-749-011-37 s PHOTO COUPLER TLP181(BL-TPR) IC759 8-759-592-42 s IC TC7SZ00FU(TE85R) PH301 8-749-014-35 s IC HCPL-0630-500 IC760 8-759-592-42 s IC TC7SZ00FU(TE85R) PH302 8-749-014-35 s IC HCPL-0630-500 IC761 8-759-592-42 s IC TC7SZ00FU(TE85R) 6-11 HDCU2500...
Page 174
1-208-915-81 s RES, CHIP 15K (1005) R167 1-208-935-81 s RES, CHIP 100K (1005) 1-208-919-81 s RES, CHIP 22K (1005) R168 1-208-911-81 s RES, CHIP 10K (1005) 1-208-887-81 s RES, CHIP 1.0K (1005) R169 1-208-911-81 s RES, CHIP 10K (1005) 6-12 HDCU2500...
Page 175
1-208-863-81 s RES, CHIP 100 (1005) R355 1-208-863-81 s RES, CHIP 100 (1005) R235 1-208-935-81 s RES, CHIP 100K (1005) R356 1-208-863-81 s RES, CHIP 100 (1005) R236 1-208-935-81 s RES, CHIP 100K (1005) R357 1-208-863-81 s RES, CHIP 100 (1005) 6-13 HDCU2500...
Page 176
1-208-911-81 s RES, CHIP 10K (1005) R608 1-208-927-81 s RES, CHIP 47K (1005) R462 1-208-911-81 s RES, CHIP 10K (1005) R609 1-208-911-81 s RES, CHIP 10K (1005) R463 1-208-927-81 s RES, CHIP 47K (1005) R610 1-208-855-81 s RES, CHIP 47 (1005) 6-14 HDCU2500...
Page 177
1-208-899-81 s RES, CHIP 3.3K (1005) R810 1-208-895-81 s RES, CHIP 2.2K (1005) R746 1-208-911-81 s RES, CHIP 10K (1005) R811 1-244-161-81 s RES, CHIP 2.2 (1005) R747 1-208-879-81 s RES, CHIP 470 (1005) R812 1-244-161-81 s RES, CHIP 2.2 (1005) 6-15 HDCU2500...
Page 178
1-208-863-81 s RES, CHIP 100 (1005) R967 1-220-870-81 s RES, CHIP 10 (1005) R890 1-208-863-81 s RES, CHIP 100 (1005) R969 1-208-863-81 s RES, CHIP 100 (1005) R891 1-208-863-81 s RES, CHIP 100 (1005) R970 1-208-863-81 s RES, CHIP 100 (1005) 6-16 HDCU2500...
Page 179
1-762-118-21 s SWITCH, TOGGLE 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-112-717-91 s CAP, CERAMIC 1UF B (1005) S402 1-762-120-21 s SWITCH, TOGGLE 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 S403 1-572-658-21 s SWITCH, ROTARY S404 1-572-658-21 s SWITCH, ROTARY 6-17 HDCU2500...
Page 180
6-502-598-01 s DI SML-D12U8WT86 1-208-911-81 s RES, CHIP 10K (1005) 6-502-598-01 s DI SML-D12U8WT86 1-208-923-81 s RES, CHIP 33K (1005) 6-502-598-01 s DI SML-D12U8WT86 1-208-907-81 s RES, CHIP 6.8K (1005) 1-208-879-81 s RES, CHIP 470 (1005) 6-502-598-01 s DI SML-D12U8WT86 6-18 HDCU2500...
Page 181
1-208-895-81 s RES, CHIP 2.2K (1005) C106 1-112-298-91 s CAP, CERAMIC 1MF B (1608) 1-208-895-81 s RES, CHIP 2.2K (1005) C108 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005 1-208-919-81 s RES, CHIP 22K (1005) C109 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005 6-19 HDCU2500...
Page 182
1-164-840-81 s CAP, CHIP CERAMIC 1PF CK 1005 C306 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C371 1-164-840-81 s CAP, CHIP CERAMIC 1PF CK 1005 C307 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C401 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005 6-20 HDCU2500...
Page 183
1-112-692-81 s CAP,CHIP CERAMIC1000PF CH 1005 C620 1-114-214-81 s CAP,CHIP CERAMIC470PF CH1005 C471 1-114-214-81 s CAP,CHIP CERAMIC470PF CH1005 C621 1-112-692-81 s CAP,CHIP CERAMIC1000PF CH 1005 C472 1-112-692-81 s CAP,CHIP CERAMIC1000PF CH 1005 C622 1-112-692-81 s CAP,CHIP CERAMIC1000PF CH 1005 6-21 HDCU2500...
Page 184
6-502-526-01 s DI UDZSUSTE-172.0B C709 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C710 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 D501 6-502-526-01 s DI UDZSUSTE-172.0B C711 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 D502 6-502-526-01 s DI UDZSUSTE-172.0B 6-22 HDCU2500...
Page 185
IC311 8-759-675-54 s IC TC7W53FK(TE85R) FB304 1-400-832-21 s SMD EMI FERRITE IC312 8-759-561-46 s IC AD8014ARTZ-REEL7 FB305 1-400-832-21 s SMD EMI FERRITE IC313 8-759-675-54 s IC TC7W53FK(TE85R) FB306 1-400-832-21 s SMD EMI FERRITE IC314 8-759-561-46 s IC AD8014ARTZ-REEL7 6-23 HDCU2500...
Page 186
6-600-477-01 s IC TLP281(GB-TP,F) Q605 8-729-928-25 s TRANSISTOR 2SA1774TL-QR PH702 6-600-477-01 s IC TLP281(GB-TP,F) Q606 8-729-928-05 s TRANSISTOR 2SC4617TL-QR PH703 6-600-477-01 s IC TLP281(GB-TP,F) PH704 6-600-477-01 s IC TLP281(GB-TP,F) Q607 8-729-013-37 s TRANSISTOR 2SC4213-AB-TE85L Q608 8-729-013-37 s TRANSISTOR 2SC4213-AB-TE85L 6-24 HDCU2500...
Page 187
1-208-879-81 s RES, CHIP 470 (1005) R177 1-208-887-81 s RES, CHIP 1.0K (1005) R103 1-208-871-81 s RES, CHIP 220 (1005) R201 1-208-863-81 s RES, CHIP 100 (1005) R104 1-208-871-81 s RES, CHIP 220 (1005) R202 1-208-863-81 s RES, CHIP 100 (1005) 6-25 HDCU2500...
Page 188
1-208-907-81 s RES, CHIP 6.8K (1005) R441 1-208-911-81 s RES, CHIP 10K (1005) R337 1-208-907-81 s RES, CHIP 6.8K (1005) R445 1-208-911-81 s RES, CHIP 10K (1005) R338 1-208-863-81 s RES, CHIP 100 (1005) R446 1-208-911-81 s RES, CHIP 10K (1005) 6-26 HDCU2500...
Page 189
1-208-863-81 s RES, CHIP 100 (1005) R587 1-208-919-81 s RES, CHIP 22K (1005) R523 1-208-863-81 s RES, CHIP 100 (1005) R588 1-208-959-81 s RES, CHIP 1M (1005) R524 1-208-919-81 s RES, CHIP 22K (1005) R589 1-208-959-81 s RES, CHIP 1M (1005) 6-27 HDCU2500...
Page 190
1-208-915-81 s RES, CHIP 15K (1005) R732 1-208-911-81 s RES, CHIP 10K (1005) R664 1-208-919-81 s RES, CHIP 22K (1005) R733 1-208-911-81 s RES, CHIP 10K (1005) R665 1-208-919-81 s RES, CHIP 22K (1005) R734 1-208-911-81 s RES, CHIP 10K (1005) 6-28 HDCU2500...
Page 191
1-208-959-81 s RES, CHIP 1M (1005) R877 1-208-887-81 s RES, CHIP 1.0K (1005) R809 1-208-915-81 s RES, CHIP 15K (1005) R878 1-208-887-81 s RES, CHIP 1.0K (1005) R810 1-208-919-81 s RES, CHIP 22K (1005) R879 1-208-887-81 s RES, CHIP 1.0K (1005) 6-29 HDCU2500...
Page 192
1-234-378-21 s RES, NETWORK 10K (1005X4) R945 1-218-929-81 s RES, CHIP 10 R946 1-218-929-81 s RES, CHIP 10 RB401 1-234-372-21 s RES, NETWORK 100 (1005X4) R947 1-218-929-81 s RES, CHIP 10 RB402 1-234-372-21 s RES, NETWORK 100 (1005X4) 6-30 HDCU2500...
Page 193
1-239-897-31 s FILTER, EMI (SMD) Ref. No. 1-239-897-31 s FILTER, EMI (SMD) or Q'ty Part No. SP Description 1-239-897-31 s FILTER, EMI (SMD) 1-239-897-31 s FILTER, EMI (SMD) A-1161-089-B s MOUNTED CIRCUIT BOARD, CN-2675G 1-239-897-31 s FILTER, EMI (SMD) 6-31 HDCU2500...
Page 194
1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 6-32 HDCU2500...
Page 195
1-112-717-91 s CAP, CERAMIC 1UF B (1005) C306 1-112-933-11 s CAP, NIOBIUM ELECT 47MF C583 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C310 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C584 1-112-746-91 s CAP, CERAMIC 4.7MF B (1608) 6-33 HDCU2500...
Page 196
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C701 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C766 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C702 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C767 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 6-34 HDCU2500...
Page 197
1-535-877-22 s CHIP, CHECKER IC322 6-702-879-01 s IC R3112N281A-TR-FA 1-535-877-22 s CHIP, CHECKER IC324 8-759-592-47 s IC TC7SZ08FU(TE85R) IC325 8-759-592-47 s IC TC7SZ08FU(TE85R) 1-535-877-22 s CHIP, CHECKER IC326 6-713-878-01 s IC EPCS64SI16N 1-535-877-22 s CHIP, CHECKER IC327 6-707-843-01 s IC TC74LCX125FT(EKJ) 6-35 HDCU2500...
Page 198
8-729-928-05 s TRANSISTOR 2SC4617TL-QR 1-208-943-81 s RES, CHIP 220K (1005) 1-208-919-81 s RES, CHIP 22K (1005) Q210 8-729-928-05 s TRANSISTOR 2SC4617TL-QR 1-208-959-81 s RES, CHIP 1M (1005) Q211 8-729-928-05 s TRANSISTOR 2SC4617TL-QR 1-208-959-81 s RES, CHIP 1M (1005) 6-36 HDCU2500...
Page 199
1-220-878-81 s RES, CHIP 22 (1005) R396 1-208-911-81 s RES, CHIP 10K (1005) R305 1-220-878-81 s RES, CHIP 22 (1005) R397 1-208-911-81 s RES, CHIP 10K (1005) R306 1-218-990-81 s CONDUCTOR, CHIP (1005) R398 1-208-911-81 s RES, CHIP 10K (1005) 6-37 HDCU2500...
Page 200
1-208-919-81 s RES, CHIP 22K (1005) R563 1-220-878-81 s RES, CHIP 22 (1005) R466 1-208-919-81 s RES, CHIP 22K (1005) R564 1-208-919-81 s RES, CHIP 22K (1005) R469 1-208-863-81 s RES, CHIP 100 (1005) R565 1-208-887-81 s RES, CHIP 1.0K (1005) 6-38 HDCU2500...
Page 201
1-234-372-21 s RES, NETWORK 100 (1005X4) RB645 1-234-372-21 s RES, NETWORK 100 (1005X4) RB227 1-234-372-21 s RES, NETWORK 100 (1005X4) RB646 1-234-372-21 s RES, NETWORK 100 (1005X4) RB229 1-234-372-21 s RES, NETWORK 100 (1005X4) RB647 1-234-372-21 s RES, NETWORK 100 (1005X4) 6-39 HDCU2500...
Page 202
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C106 1-116-346-11 s CAP, ELECT 47MF 105 C171 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C107 1-116-346-11 s CAP, ELECT 47MF 105 C172 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 6-40 HDCU2500...
Page 203
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C358 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C620 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C359 1-126-391-21 s CAP, CHIP ELECT 47MF (5X5.7) C621 1-112-717-91 s CAP, CERAMIC 1UF B (1005) 6-41 HDCU2500...
Page 204
1-112-717-91 s CAP, CERAMIC 1UF B (1005) C833 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C904 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C834 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C905 1-112-717-91 s CAP, CERAMIC 1UF B (1005) 6-42 HDCU2500...
Page 205
1-414-398-41 s INDUCTOR (SMD) 10.0UH IC108 6-712-135-01 o IC R1173H001D-T1-F L501 1-414-398-41 s INDUCTOR (SMD) 10.0UH IC109 8-759-346-27 s IC LM45BIM3X IC110 8-759-338-95 s IC NJM2903V(TE2) L601 1-414-392-41 s INDUCTOR (SMD) 1.0UH L602 1-414-398-41 s INDUCTOR (SMD) 10.0UH 6-43 HDCU2500...
Page 206
1-208-919-81 s RES, CHIP 22K (1005) R208 1-218-990-81 s CONDUCTOR, CHIP (1005) R119 1-208-911-81 s RES, CHIP 10K (1005) R215 1-208-935-81 s RES, CHIP 100K (1005) R120 1-208-923-81 s RES, CHIP 33K (1005) R216 1-218-990-81 s CONDUCTOR, CHIP (1005) 6-44 HDCU2500...
Page 207
1-208-891-81 s RES, CHIP 1.5K (1005) R420 1-218-990-81 s CONDUCTOR, CHIP (1005) R351 1-208-875-81 s RES, CHIP 330 (1005) R422 1-220-878-81 s RES, CHIP 22 (1005) R352 1-208-863-81 s RES, CHIP 100 (1005) R423 1-220-878-81 s RES, CHIP 22 (1005) 6-45 HDCU2500...
Page 208
1-208-887-81 s RES, CHIP 1.0K (1005) R614 1-218-990-81 s CONDUCTOR, CHIP (1005) R544 1-208-887-81 s RES, CHIP 1.0K (1005) R616 1-220-870-81 s RES, CHIP 10 (1005) R545 1-208-887-81 s RES, CHIP 1.0K (1005) R617 1-220-870-81 s RES, CHIP 10 (1005) 6-46 HDCU2500...
Page 209
1-234-373-21 s RES, NETWORK 220 (1005X4) RB719 1-234-372-21 s RES, NETWORK 100 (1005X4) RB202 1-234-373-21 s RES, NETWORK 220 (1005X4) RB720 1-234-372-21 s RES, NETWORK 100 (1005X4) RB203 1-234-373-21 s RES, NETWORK 220 (1005X4) RB721 1-234-371-21 s RES, NETWORK 47 (1005X4) 6-47 HDCU2500...
Page 210
1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C234 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C109 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C235 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C236 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B 6-48 HDCU2500...
Page 211
1-162-915-91 s CAP, CERAMIC 10PF CH 1608 C352 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C417 1-162-913-91 s CAP, CERAMIC 8.0PF CH 1608 C353 1-165-989-91 s CAP, CERAMIC 10MF (2012) C418 1-162-915-91 s CAP, CERAMIC 10PF CH 1608 6-49 HDCU2500...
Page 212
IC118 8-759-338-95 s IC NJM2903V(TE2) L326 1-414-398-41 s INDUCTOR (SMD) 10.0UH IC201 8-759-675-47 s IC SN74LVC04APWR L327 1-414-398-41 s INDUCTOR (SMD) 10.0UH IC202 8-759-675-47 s IC SN74LVC04APWR IC207 8-759-472-65 s IC 74VHC574MTCX L501 1-414-398-41 s INDUCTOR (SMD) 10.0UH 6-50 HDCU2500...
Page 213
1-211-969-91 s RES, CHIP 10 (1608) R313 1-218-871-91 s RES, CHIP 10K (1608) R155 1-218-871-91 s RES, CHIP 10K (1608) R314 1-218-871-91 s RES, CHIP 10K (1608) R156 1-218-823-91 s RES, CHIP 100 (1608) R315 1-211-985-91 s RES, CHIP 47 (1608) 6-51 HDCU2500...
Page 214
1-218-827-91 s RES, CHIP 150 (1608) R501 1-218-871-91 s RES, CHIP 10K (1608) R393 1-218-823-91 s RES, CHIP 100 (1608) R502 1-218-871-91 s RES, CHIP 10K (1608) R394 1-218-823-91 s RES, CHIP 100 (1608) R503 1-218-847-91 s RES, CHIP 1.0K (1608) 6-52 HDCU2500...
Page 215
1-234-373-21 s RES, NETWORK 220 (1005X4) RB329 1-234-373-21 s RES, NETWORK 220 (1005X4) RB207 1-234-373-21 s RES, NETWORK 220 (1005X4) RB330 1-234-373-21 s RES, NETWORK 220 (1005X4) RB210 1-234-372-21 s RES, NETWORK 100 (1005X4) RB331 1-234-373-21 s RES, NETWORK 220 (1005X4) 6-53 HDCU2500...
Page 216
1-162-915-91 s CAP, CERAMIC 10PF CH 1608 C109 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C209 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216 C110 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225 C210 1-162-919-91 s CAP, CERAMIC 22PF CH 1608 6-54 HDCU2500...
Page 217
1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C306 1-165-989-91 s CAP, CERAMIC 10MF (2012) C372 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C307 1-162-923-91 s CAP, CERAMIC 47PF CH 1608 C373 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B 6-55 HDCU2500...
Page 218
1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C516 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C581 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C517 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C582 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B 6-56 HDCU2500...
Page 219
8-759-561-46 s IC AD8014ARTZ-REEL7 FB301 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC516 8-759-523-02 s IC TC74HC4053AFT(EL) FB302 1-469-094-21 s FERRITE, EMI (SMD) (1608) IC517 8-759-523-02 s IC TC74HC4053AFT(EL) IC518 6-707-885-01 s IC TC74VHCT08AFT(EKJ) FL501 1-813-437-11 s FILTER, LOW PASS (10MHZ) 6-57 HDCU2500...
Page 220
1-414-398-41 s INDUCTOR (SMD) 10.0UH R141 1-218-855-91 s RES, CHIP 2.2K (1608) L521 1-414-398-41 s INDUCTOR (SMD) 10.0UH R142 1-218-863-91 s RES, CHIP 4.7K (1608) L522 1-414-398-41 s INDUCTOR (SMD) 10.0UH R143 1-218-887-91 s RES, CHIP 47K (1608) 6-58 HDCU2500...
Page 221
1-218-823-91 s RES, CHIP 100 (1608) R305 1-218-883-91 s RES, CHIP 33K (1608) R238 1-218-871-91 s RES, CHIP 10K (1608) R306 1-218-879-91 s RES, CHIP 22K (1608) R239 1-218-823-91 s RES, CHIP 100 (1608) R307 1-218-847-91 s RES, CHIP 1.0K (1608) 6-59 HDCU2500...
Page 222
1-218-851-91 s RES, CHIP 1.5K (1608) R453 1-218-831-91 s RES, CHIP 220 (1608) R382 1-216-864-91 s CONDUCTOR, CHIP (1608) R454 1-218-831-91 s RES, CHIP 220 (1608) R383 1-216-864-91 s CONDUCTOR, CHIP (1608) R455 1-218-831-91 s RES, CHIP 220 (1608) 6-60 HDCU2500...
Page 223
1-218-859-91 s RES, CHIP 3.3K (1608) R624 1-218-823-91 s RES, CHIP 100 (1608) R560 1-216-864-91 s CONDUCTOR, CHIP (1608) R625 1-218-823-91 s RES, CHIP 100 (1608) R561 1-218-843-91 s RES, CHIP 680 (1608) R626 1-218-823-91 s RES, CHIP 100 (1608) 6-61 HDCU2500...
Page 224
1-234-381-21 s RES, NETWORK 100K (1005X4) RB244 1-234-373-21 s RES, NETWORK 220 (1005X4) RB107 1-234-372-21 s RES, NETWORK 100 (1005X4) RB245 1-234-373-21 s RES, NETWORK 220 (1005X4) RB108 1-234-372-21 s RES, NETWORK 100 (1005X4) RB246 1-234-373-21 s RES, NETWORK 220 (1005X4) 6-62 HDCU2500...
Page 225
1-128-589-21 s CAP, CHIP ELECT 47MF RB524 1-234-373-21 s RES, NETWORK 220 (1005X4) RB525 1-234-373-21 s RES, NETWORK 220 (1005X4) C101 1-100-507-91 s CAP, CERAMIC 4.7MF C (1608) RB526 1-234-373-21 s RES, NETWORK 220 (1005X4) C102 1-100-507-91 s CAP, CERAMIC 4.7MF C (1608) 6-63 HDCU2500...
Page 226
1-218-990-81 s CONDUCTOR, CHIP (1005) L252 1-414-836-21 s INDUCTOR, CHIP 4.7NH (1005) R120 1-218-990-81 s CONDUCTOR, CHIP (1005) 6-550-631-01 s TRANSISTOR 2SA1797-T100-Q R201 1-208-856-81 s RES, CHIP 51 (1005) 8-729-928-05 s TRANSISTOR 2SC4617TL-QR R202 1-208-863-81 s RES, CHIP 100 (1005) 6-64 HDCU2500...
Page 227
A-1860-186-A s MOUNTED CIRCUIT BOARD, LE-379 CN102 1-793-324-21 s CONNECTOR, COAXIAL (BNC TYPE) CN103 1-793-324-21 s CONNECTOR, COAXIAL (BNC TYPE) 1-784-435-21 o CONNECTOR, BOARD TO BOARD 30P CN104 1-793-324-21 s CONNECTOR, COAXIAL (BNC TYPE) 6-502-598-01 s DI SML-D12U8WT86 6-65 HDCU2500...
Page 228
C2010 1-115-416-91 s CAP,CHIP CERAMIC1000PF CH 1608 C131 1-165-947-91 s CAP, CHIP CERAMIC 2.2MF B 3225 C2011 1-115-416-91 s CAP,CHIP CERAMIC1000PF CH 1608 C132 1-164-315-91 s CAP, CERAMIC 470PF CH (1608) C2023 1-115-416-91 s CAP,CHIP CERAMIC1000PF CH 1608 6-66 HDCU2500...
Page 229
R112 1-211-969-91 s RES, CHIP 10 (1608) IC1003 6-715-288-01 s IC MIP2E3DMY0LT R113 1-216-791-91 s RES, CHIP 3.3 (1608) IC1004 6-711-947-01 s IC MM1431CURE R114 1-211-969-91 s RES, CHIP 10 (1608) R115 1-216-791-91 s RES, CHIP 3.3 (1608) 6-67 HDCU2500...
Page 230
1-243-639-11 s RES, METAL PLATE 0.1 R1062 1-218-859-91 s RES, CHIP 3.3K (1608) R190 1-219-759-51 s RESISTOR (SURGE RESISTANT) 1M R1064 1-218-907-91 s RES, CHIP 330K (1608) R1066 1-211-985-91 s RES, CHIP 47 (1608) R191 1-218-871-91 s RES, CHIP 10K (1608) 6-68 HDCU2500...
Page 231
1-116-346-11 s CAP, ELECT 47MF 105 R2126 1-220-285-91 s RES,SQUARE TYPE CHIP 10K(3225) R2127 1-220-293-91 s RES,SQUARE TYPE CHIP 47K(3225) 1-116-346-11 s CAP, ELECT 47MF 105 R2128 1-220-293-91 s RES,SQUARE TYPE CHIP 47K(3225) 1-112-692-81 s CAP,CHIP CERAMIC1000PF CH 1005 6-69 HDCU2500...
Page 232
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C206 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C395 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C210 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C399 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 6-70 HDCU2500...
Page 233
C616 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C464 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C617 1-112-933-11 s CAP, NIOBIUM ELECT 47MF C465 1-112-815-91 s CAP, CERAMIC 10MF C (1608) C618 1-112-933-11 s CAP, NIOBIUM ELECT 47MF 6-71 HDCU2500...
Page 234
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 FB402 1-414-864-21 s FERRITE, EMI (SMD) (1608) FB501 1-481-195-21 s FERRITE, EMI (SMD) C986 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 FB502 1-481-195-21 s FERRITE, EMI (SMD) C987 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 6-72 HDCU2500...
Page 235
1-208-863-81 s RES, CHIP 100 (1005) IC581 6-702-535-01 s IC MC100LVEL11DTR2 1-208-863-81 s RES, CHIP 100 (1005) 1-457-372-21 s COIL, CHOKE 1UH 1-208-863-81 s RES, CHIP 100 (1005) 1-457-372-21 s COIL, CHOKE 1UH 1-208-871-81 s RES, CHIP 220 (1005) 6-73 HDCU2500...
Page 236
1-208-911-81 s RES, CHIP 10K (1005) R313 1-208-887-81 s RES, CHIP 1.0K (1005) 1-208-911-81 s RES, CHIP 10K (1005) R315 1-220-870-81 s RES, CHIP 10 (1005) 1-218-990-81 s CONDUCTOR, CHIP (1005) R316 1-220-870-81 s RES, CHIP 10 (1005) 6-74 HDCU2500...
Page 237
1-208-911-81 s RES, CHIP 10K (1005) R525 1-220-870-81 s RES, CHIP 10 (1005) R393 1-208-911-81 s RES, CHIP 10K (1005) R526 1-220-878-81 s RES, CHIP 22 (1005) R394 1-208-911-81 s RES, CHIP 10K (1005) R527 1-208-875-81 s RES, CHIP 330 (1005) 6-75 HDCU2500...
Page 238
1-208-911-81 s RES, CHIP 10K (1005) RB251 1-234-375-21 s RES, NETWORK 1K (1005X4) RB252 1-234-372-21 s RES, NETWORK 100 (1005X4) R595 1-208-911-81 s RES, CHIP 10K (1005) RB301 1-234-371-21 s RES, NETWORK 47 (1005X4) R596 1-208-919-81 s RES, CHIP 22K (1005) 6-76 HDCU2500...
Page 239
1-795-671-12 s OSCILLATOR, CRYSTAL (VCXO)3.3V RB602 1-234-371-21 s RES, NETWORK 47 (1005X4) X542 1-795-670-12 s OSCILLATOR, CRYSTAL (VCXO)3.3V RB603 1-234-371-21 s RES, NETWORK 47 (1005X4) RB604 1-234-371-21 s RES, NETWORK 47 (1005X4) RB605 1-234-371-21 s RES, NETWORK 47 (1005X4) 6-77 HDCU2500...
Page 240
1-100-597-91 s CAP, CHIP CERAMIC 0.1MF B 1608 C7025 1-162-923-91 s CAP, CERAMIC 47PF CH 1608 C7104 1-100-597-91 s CAP, CHIP CERAMIC 0.1MF B 1608 C7026 1-100-597-91 s CAP, CHIP CERAMIC 0.1MF B 1608 C8001 1-100-597-91 s CAP, CHIP CERAMIC 0.1MF B 1608 6-78 HDCU2500...
Page 241
1-457-907-11 s COIL, CHOKE 16UH D7006 6-500-528-01 s DIODE DE5SC6M-7071 D7007 8-719-938-77 s DIODE SB05-05C-TB-E L7005 1-456-622-21 s COIL, CHOKE 1UH D7008 8-719-938-77 s DIODE SB05-05C-TB-E L7006 1-456-046-21 s COIL, CHOKE (SMD) 10UH(10X10) L7007 1-456-622-21 s COIL, CHOKE 1UH 6-79 HDCU2500...
Page 242
1-208-923-81 s RES, CHIP 33K (1005) R7040 1-208-959-81 s RES, CHIP 1M (1005) R6017 1-208-903-81 s RES, CHIP 4.7K (1005) R7041 1-208-875-81 s RES, CHIP 330 (1005) R6018 1-219-684-21 s RES, CHIP (SQUARE TYPE) 0.01 R7042 1-208-911-81 s RES, CHIP 10K (1005) 6-80 HDCU2500...
Page 243
RB8017 1-234-375-21 s RES, NETWORK 1K (1005X4) R7125 1-208-923-81 s RES, CHIP 33K (1005) R7126 1-208-935-81 s RES, CHIP 100K (1005) 1-445-786-11 s TRANSFORMER, CONVERTER (STBY) R7127 1-208-911-81 s RES, CHIP 10K (1005) TP6001 1-535-877-22 s CHIP, CHECKER 6-81 HDCU2500...
Page 244
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C101 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C511 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C102 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C601 1-100-881-91 s CAP, CERAMIC 47MF C (3216) 6-82 HDCU2500...
Page 245
1-414-398-41 s INDUCTOR (SMD) 10.0UH 1-208-899-81 s RES, CHIP 3.3K (1005) 1-218-990-81 s CONDUCTOR, CHIP (1005) 6-550-631-01 s TRANSISTOR 2SA1797-T100-Q 1-208-895-81 s RES, CHIP 2.2K (1005) 6-550-632-01 s TRANSISTOR 2SC4672-T100-Q 1-208-911-81 s RES, CHIP 10K (1005) 8-729-035-99 s TRANSISTOR 2SA1615-Z-E2 6-83 HDCU2500...
Page 246
C105 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 R316 1-220-878-81 s RES, CHIP 22 (1005) R505 1-208-943-81 s RES, CHIP 220K (1005) C108 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 R506 1-208-899-81 s RES, CHIP 3.3K (1005) 6-84 HDCU2500...
Page 247
1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C180 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C348 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C181 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C349 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 6-85 HDCU2500...
Page 248
1-112-717-91 s CAP, CERAMIC 1UF B (1005) C512 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C847 1-112-717-91 s CAP, CERAMIC 1UF B (1005) C513 1-114-582-91 s CAP, CERAMIC 0.1MF B 1005 C854 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005 6-86 HDCU2500...
Page 249
1-780-408-11 o TERMINAL, LUG IC600 6-706-487-01 s IC TC7SH08FU IC602 6-706-487-01 s IC TC7SH08FU 1-780-408-11 o TERMINAL, LUG E100 1-694-974-21 s CONTACT TERMINAL IC603 8-759-592-49 s IC TC7SZ125FU(TE85R) E101 1-694-974-21 s CONTACT TERMINAL IC604 6-707-843-01 s IC TC74LCX125FT(EKJ) 6-87 HDCU2500...
Page 250
1-208-919-81 s RES, CHIP 22K (1005) Q404 8-729-928-82 s TRANSISTOR DTC144EE-TL R157 1-218-990-81 s CONDUCTOR, CHIP (1005) Q405 8-729-928-82 s TRANSISTOR DTC144EE-TL R158 1-208-943-81 s RES, CHIP 220K (1005) Q600 8-729-928-25 s TRANSISTOR 2SA1774TL-QR R159 1-208-919-81 s RES, CHIP 22K (1005) 6-88 HDCU2500...
Page 251
1-208-907-81 s RES, CHIP 6.8K (1005) R477 1-218-990-81 s CONDUCTOR, CHIP (1005) R247 1-208-911-81 s RES, CHIP 10K (1005) R478 1-218-990-81 s CONDUCTOR, CHIP (1005) R248 1-208-911-81 s RES, CHIP 10K (1005) R479 1-218-990-81 s CONDUCTOR, CHIP (1005) 6-89 HDCU2500...
Page 252
1-218-990-81 s CONDUCTOR, CHIP (1005) R771 1-218-990-81 s CONDUCTOR, CHIP (1005) R623 1-208-863-81 s RES, CHIP 100 (1005) R847 1-208-871-81 s RES, CHIP 220 (1005) R624 1-208-855-81 s RES, CHIP 47 (1005) R848 1-208-871-81 s RES, CHIP 220 (1005) 6-90 HDCU2500...
Page 253
1-220-878-81 s RES, CHIP 22 (1005) X803 1-795-671-12 s OSCILLATOR, CRYSTAL (VCXO)3.3V R935 1-220-878-81 s RES, CHIP 22 (1005) X900 1-814-291-11 s OSCILLATOR, CRYSTAL (25MHZ) R936 1-220-878-81 s RES, CHIP 22 (1005) R937 1-220-878-81 s RES, CHIP 22 (1005) 6-91 HDCU2500...
Page 254
1-218-843-91 s RES, CHIP 680 (1608) L204 1-414-398-41 s INDUCTOR (SMD) 10.0UH R227 1-211-990-91 s RES, CHIP 75 (1608) R228 1-211-990-91 s RES, CHIP 75 (1608) L205 1-414-398-41 s INDUCTOR (SMD) 10.0UH R229 1-218-887-91 s RES, CHIP 47K (1608) 8-729-209-73 s TRANSISTOR 2SA1213Y-TE12L 6-92 HDCU2500...
Page 255
1-218-887-91 s RES, CHIP 47K (1608) 8-759-327-01 s IC NJM062V(TE2) R140 1-218-887-91 s RES, CHIP 47K (1608) 8-759-338-95 s IC NJM2903V(TE2) R141 1-211-977-91 s RES, CHIP 22 (1608) IC102 8-759-561-46 s IC AD8014ARTZ-REEL7 R144 1-218-859-91 s RES, CHIP 3.3K (1608) 6-93 HDCU2500...
Page 256
1-128-589-21 s CAP, CHIP ELECT 47MF 8-719-024-81 s DIODE 1SS300-TE85L 8-719-024-81 s DIODE 1SS300-TE85L 1-126-399-21 s CAP, CHIP ELECT 10MF (5X5.7) 8-719-024-81 s DIODE 1SS300-TE85L 1-126-399-21 s CAP, CHIP ELECT 10MF (5X5.7) 8-719-056-48 s DI 1SS388 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005 6-94 HDCU2500...
Page 257
1-535-877-22 s CHIP, CHECKER 1-208-911-81 s RES, CHIP 10K (1005) 1-208-887-81 s RES, CHIP 1.0K (1005) 8-759-327-01 s IC NJM062V(TE2) 1-208-887-81 s RES, CHIP 1.0K (1005) 6-704-976-01 s IC ADR381ARTZ-REEL7 1-208-923-81 s RES, CHIP 33K (1005) 8-759-561-46 s IC AD8014ARTZ-REEL7 6-95 HDCU2500...
Page 258
1-233-578-21 s RES, CHIP NETWORK 47K (3216) R113 1-208-911-81 s RES, CHIP 10K (1005) R114 1-208-911-81 s RES, CHIP 10K (1005) RB51 1-233-577-21 s RES, CHIP NETWORK 470 (3216) R115 1-208-863-81 s RES, CHIP 100 (1005) RB52 1-233-578-21 s RES, CHIP NETWORK 47K (3216) 6-96 HDCU2500...
Page 259
RB108 1-233-578-21 s RES, CHIP NETWORK 47K (3216) THP1 1-804-458-21 s THERMISTOR, POSITIVE THP2 1-804-458-21 s THERMISTOR, POSITIVE THP3 1-803-615-21 s THERMISTOR, POSITIVE THP4 1-803-615-21 s THERMISTOR, POSITIVE THP5 1-803-615-21 s THERMISTOR, POSITIVE THP6 1-804-458-21 s THERMISTOR, POSITIVE 6-97 HDCU2500...
Page 260
6-4. Supplied Accessories HDCU2500 Q'ty Part No. SP Description A-8278-054-B s REMOTE INDICATOR ASSY 4-413-602-01 s OPERATION MANUAL (JAPANESE) 4-413-603-01 s OPERATION MANUAL (ENGLISH) HKCU1001 Q'ty Part No. SP Description 1-560-343-11 s CONNECTOR, 4P PLUG (M) HKCU1003 Q'ty Part No.
Page 263
+15V HV D6001 IC6002,6021 OVER V Overall (3/3) PH66 LOW V AC RELAY ON AC RELAY ON +13V OCP 601-6 105-6 OVER C HDCU2500 PFC OK PH63 PFC OK 601-4 105-4 CXA ON PH62 CXA ON 601-3 105-3 ERROR STOP PH65...
Page 341
08 : SYNTH(185) 100k 001-G5 PGOOD_+0.9V 09 : PHY LUG TERMINAL for cournor screw hole side A side B ON BOARD CONTACT E101 E103 E105 E100 E102 E104 SDP-17 (1/9) side A side B BOARD No. 1-885-980-11 SDP-17_1 8-77 HDCU2500...
Page 360
AU-340 The location is described at the end in this section. R111 D16 D17 FB20 FB19 FB18 FB17 R105 R110 R109 Q8 Q9 R101 R120 AU-340 AU-340 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 HDCU2500...
Page 362
R737 R738 AVP-15 -B SIDE- SUFFIX: -11 CN-2675G CN-2676 The location is described at the end in this section. CN-2676 CN-2676 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 CN-2675G CN-2675G -A SIDE- -B SIDE- CN11 SUFFIX: -12 SUFFIX: -12 HDCU2500...
Page 363
-A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 CN-3451 CN-3451 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 CNB-29A The location is described at the end in this section. CNB-29A CNB-29A -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 HDCU2500...
Page 370
The location is described at the end in this section. R163 L152 R155 R160 R153 R161 C155 L151 R162 R157 R159 R263 L252 R255 R260 R253 R261 C255 L251 R262 R257 R259 HIF-57 HIF-57 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 9-14 HDCU2500...
Page 371
R253 R261 L251 C255 R262 R257 R259 HIF-62 HIF-62 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 LE-379 The location is described at the end in this section. LE-379 LE-379 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 9-15 HDCU2500...
Page 372
MB-1181 The location is described at the end in this section. CN21 MB-1181 MB-1181 -A SIDE- -B SIDE- SUFFIX: -11 SUFFIX: -11 9-16 HDCU2500...
Page 391
20 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 1.5 k Z 0.15 μF voltmeter (5.25V) Earth Ground Fig A. Using an AC voltmeter to check AC leakage. HDCU2500...