HP 8920A User Manual page 622

view of, 122
AMPS-TACS
control channel decoder,
forward control channel,
forward voice channel, 355
radio standard, 366
reverse control channel, 276
reverse voice channel, 276
simulated system, 136
voice channel decoder, 271
AMPS-TACS decoder mode
AF Anl In, 272
Arm Meas, 272
Channel, 272
Data (hex), 273
Gate Time, 273
Input Level, 273
Num of Bits, 274
Polarity, 274
Single/Cont, 275
Stop Meas, 275
Trig Level, 275
Trigger Pattern (bin), 275
view of, 271
AMPS-TACS encoder mode
AFGen2 To, 356
Audio Out, 356
B/I Delay, 357
Bursts, 357
Busy/Idle, 357
Channel, 357
Data Level, 357
Data Rate, 358
Filler, 359
FM Coupling, 360
Message, 361, 362
Polarity, 364
SAT Freq, 365
SAT Level, 365
Send, 365
Send Filler, 365
Send Mode, 366
Standard, 366
Stop, 366
Stop Filler, 366
view of, 355
Analog Meas screen
AF Anl In, 244
622
AF Freq,
AFGen1 Freq,
271 AFGen1 To,
355 Amplitude,
De-Emphasis,
Detector,
Filter 1,
Filter 2,
FM Deviation,
TX Freq Error,
TX Power,
view of,
analog meter,
analyzer
arming measurements, 275, 283, 288,
292, 297, 303, 308, 320,
calibration,
disarming measurements,
frequency, markers,
input port,
level, markers,
analyzer, AF
CDCSS decoder settings,
input, 272, 280, 285, 289, 295, 301,
305, 317,
level, 273, 282, 287, 291, 296, 302,
306, 319,
analyzer, RF
frequency, 351, 479,
input attenuation,
input port,
level, 473
measurements,
sensitivity,
tuning, 351, 479,
ANT IN connector
avoiding damage, 58, 95, 112, 349,
352, 476, 480, 508, 557, 559,
connecting to, 40,
description,
for ACP ratio measurements, 91,
for off-the-air measurements, 95, 310,
349, 476,
for RF measurements, 95, 349, 476,
557
gain at,
input attenuation, 94, 475,
loss at, 255
245
245
245
245
245
246
246
246
246
246
246
244
62
337
518
297
514
508
514
284
335
336
558
475
476
478
477
558
562
508
562
95
557
255
515
sensitivity, 477, 517
Antenna In
Configure screen, 255
Area #
Signaling Encoder screen, NMT mode,
423
Area 1
Signaling Encoder screen, LTR mode,
397
Area 2
Signaling Encoder screen, LTR mode,
397
arm
measurment, 272, 275, 281, 283, 285,
288, 289, 292, 296, 297, 302, 303,
305, 308, 320, 335, 337
radio interface interrupt, 461
Arm Meas
Signaling Decoder screen, AMPS-
TACS mode, 272
Signaling Decoder screen, CDCSS
mode, 281
Signaling Decoder screen, Digi Page
mode, 285
Signaling Decoder screen, DTMF
mode, 289
Signaling Decoder screen, EDACS
mode, 296
Signaling Decoder screen, Func Gen
mode, 302
Signaling Decoder screen, LTR mode,
305
Signaling Decoder screen, NAMPS-
NTACS mode, 272
Signaling Decoder screen, Tone Seq
mode, 335
arrow down key, 581
arrow left key, 583
arrow up key, 581
ASCII terminal, 86
configuring, 442
ASSIGN, 82, 83
Atten Hold
Duplex Test screen, 345
RF Generator screen, 488
RX Test screen, 498
attenuation
automatic control, 94, 475,
Index
515