Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Summary of Contents for UTC Fire and Security Kidde AirSense SynaG Series
- Page 1 SynaG Series Installation Manual P/N 501-435003-1-10 • REV 1.0 • ISS 14OCT11...
- Page 2 Copyright © 2011 UTC Fire & Security. All rights reserved. Trademarks and CleanMe and the SynaG Series name are trademarks of UTC Fire & patents Security. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Content Important information ii Chapter 1 Introduction 1 Product range 2 Product compatibility 2 Operating modes 3 Chapter 2 Installation 5 Cabinet layout 6 Cabinet installation 8 Connections 9 Chapter 3 Configuration and commissioning 23 ... -
Page 4: Important Information
Important information This is the installation manual for SynaG Series conventional fire control panels. Read these instructions and all related documentation entirely before installing or operating this product. Software compatibility Information in this document applies to control panels with software version 2.0 or later. - Page 5 Installation in accordance with this manual, applicable codes, and the instructions of the authority having jurisdiction is mandatory. While every precaution has been taken during the preparation of this manual to ensure the accuracy of its contents, UTCFS assumes no responsibility for errors or omissions.
- Page 6 SynaG Series Installation Manual...
-
Page 7: Introduction
Chapter 1 Introduction Summary This chapter provides an introduction to your control panel and the available operating modes. Content Product range 2 Product compatibility 2 Operating modes 3 SynaG Series Installation Manual... -
Page 8: Product Range
Chapter 1: Introduction Product range The SynaG Series includes the models shown below. Table 1: SynaG Series models Model Description SG2000 SynaG 2 Zone conventional control panel SG2000SC SynaG 2 Zone conventional control panel with Scandinavian key switch SG4000 SynaG 4 Zone conventional control panel SG4000SC SynaG 4 Zone conventional control panel with Scandinavian key switch... -
Page 9: Operating Modes
Chapter 1: Introduction Operating modes Supported operating modes are shown in the table below. The default operating mode is EN 54-2 (with EN 54-13 supervision disabled). Table 2: Operating modes Operating mode EN 54-13 option Region available [1] EN 54-2 (default) European Union EN 54-2 Evacuation European Union (Spain) - Page 10 Chapter 1: Introduction SynaG Series Installation Manual...
-
Page 11: Installation
Chapter 2 Installation Summary This chapter explains how to install your control panel, and how to connect zones, fire system devices, and the power supply. Note: This product must be installed and maintained by qualified personnel adhering to the CEN/TS 54-14 standard (or the corresponding national standard) and any other applicable regulations. -
Page 12: Cabinet Layout
Chapter 2: Installation Cabinet layout Cabinet layout for two- and four-zone control panels Figure 1: Cabinet layout for two- and four-zone control panels 1. Seven-segment display 8. Alarm counter connector 2. Zone and fire system connectors 9. Power supply unit 3. -
Page 13: Cabinet Layout For Eight-Zone Control Panels
Chapter 2: Installation Cabinet layout for eight-zone control panels Figure 2: Cabinet layout for eight-zone control panels 1. Seven-segment display 8. Key connector 2. Zone and system connectors 9. Alarm counter connector 3. Cable knockouts 10. Fuse terminal block 4. Mounting screw knockouts 11. -
Page 14: Cabinet Installation
Chapter 2: Installation Cabinet installation Preparing the cabinet Before installing the cabinet, remove the front cover, and then remove cable knockouts from the top, bottom, and rear of the cabinet as required. Where to install the cabinet Make sure the installation location is free from construction dust and debris, and immune to extreme temperature ranges and humidity. -
Page 15: Connections
Chapter 2: Installation Figure 3: Mounting hole locations To fix the control panel cabinet to the wall: 1. Mark drill points on the wall, using the cabinet as a template. 2. Drill all required holes and insert a 6 mm wall plug into each. 3. -
Page 16: Overview Of Fire System Connections
Chapter 2: Installation Table 3: Recommended cables Cable Cable description Maximum cable length Mains cable 3 x 1.5 mm² Zone circuit cable (mixed zone) 12 to 26 AWG (3.31 to 0.13 mm²) 2 km Twisted-pair (max. 40 Ω / 500 nF) Zone circuit cable (automatic or 12 to 26 AWG (3.31 to 0.13 mm²) 2 km... - Page 17 Chapter 2: Installation Figure 5: EN 54-13 fire system connections Figure 6: BS 5839-1 fire system connections 1. A diode must be connected on the detector base. (Consult your detector installation manual for more details). SynaG Series Installation Manual...
-
Page 18: Connecting Zones And Zone Devices
Chapter 2: Installation Figure 7: Intrinsically-safe fire system connections 1. Galvanic barrier for intrinsically-safe conventional detectors. 2. Galvanic barrier for intrinsically-safe fire notification devices. Connecting zones and zone devices Connecting zones Connect zone wires as shown in Figure 4, Figure 5, Figure 6, and Figure 7 above. - Page 19 Chapter 2: Installation Terminating zones Zone termination is required at all times, whether the zone is used or not. The type of termination depends on the installation, as shown in Table 5 below. Table 5: Zone terminations Installation type Zone termination Standard and intrinsically- 4.7 kΩ...
-
Page 20: Connecting Inputs
Chapter 2: Installation Note: The default zone detection settings for each operating mode can be found in Appendix A “Configuration presets” on page 79. To change the zone detection setting, see “Advanced configuration” on page 39. Connecting inputs Input functionality Each control panel has two inputs, marked INPUT1 and INPUT2. - Page 21 Chapter 2: Installation Connecting supervised inputs Connect supervised input switches to INPUT1 and INPUT2, as shown in Figure 8 below. Figure 8: Connecting supervised inputs Nominal resistance values (including any cable resistance) are shown in Table 9 below. Table 9: Nominal resistance values for supervised inputs Input function Input Value [1]...
-
Page 22: Connecting Supervised Outputs
Chapter 2: Installation Connecting supervised outputs Control panels have the following supervised outputs: • Two-zone control panels have two outputs, marked OUT1 and OUT2. • Four- and eight-zone control panels have four outputs, marked OUT1, OUT2, OUT3, and OUT4. The outputs are supervised for open and short circuit faults. Output class The control panel outputs can be configured for Class A or Class B operation, depending on the supervision mode required. - Page 23 Chapter 2: Installation Operating mode OUT1/OUT2 OUT3/OUT4 NBN S 21-100 Evacuation sounders Warning sounders NEN 2535 Sounders Fire routing Output termination Output termination is required at all times, whether the output is used or not. The type of termination depends on the output class, as shown in Table 14 below. Table 14: Termination required for output classes Output class Output termination...
-
Page 24: Connecting The Mains Power Supply
Chapter 2: Installation Connecting the fault warning output to external equipment Note: This feature is only available in NEN 2535 mode with a 2010-1-SB supervised expansion board configured to presets 32 or 35. See “Expansion board presets” on page 86. Connect the external equipment to the OUT3 output on the 2010-1-SB supervised board. -
Page 25: Selecting 115 Or 230 Vac Operation
Chapter 2: Installation Figure 10: Connecting the mains power supply 1. Mains fuse 2. Live 3. Earth 4. Neutral For fuse specifications, see Chapter 5 “Technical specifications” on page 67. Selecting 115 or 230 VAC operation WARNING: Electrocution hazard. To avoid personal injury or death from electrocution, remove all sources of power and allow stored energy to discharge before installing or removing equipment. -
Page 26: Powering Auxiliary Equipment (24 Vdc Auxiliary Output)
Chapter 2: Installation Batteries must be installed in series, at the base of the control panel cabinet. Use the battery lead and bridge provided and connect batteries to the BATT connector on the control panel PCB, as shown below. Polarity must be observed. Note: If the control panel indicates a Supply Fault, then the batteries may need to be replaced. -
Page 27: Connecting Expansion Boards
Chapter 2: Installation Connecting expansion boards Caution: Risk of equipment damage. Always disconnect the control panel from the mains power supply before installing an expansion board. See your expansion board installation sheet for detailed installation information. Connecting a fire network Note: See the 2010-1-NB Network Board Installation Sheet for detailed installation and connection information. - Page 28 Chapter 2: Installation Figure 14: Fire network ring configuration Bus configuration Note: To be compliant with EU regulations, use this network configuration only in cases where the detection zones and mandatory EN 54-2 output functions (sounder and fire routing outputs) are not remote between panels. Bus network configuration is not normally recommended, as it does not provide for redundancy in the transmission path.
-
Page 29: Configuration And Commissioning
Chapter 3 Configuration and commissioning Summary This chapter includes information on how to configure and commission the control panel. Configuration is divided in basic configuration and advanced configuration options. Content The user interface 25 User interface for two- and four-zone control panels 25 User interface for eight-zone control panels 26 User levels 27 Configuration overview 28... - Page 30 Chapter 3: Configuration and commissioning Input configuration 47 Changing user level passwords 48 Auxiliary 24 V reset 49 Software, configuration, and serial number information 50 Expansion board configuration 51 Adding an expansion board 51 Expansion board configuration 52 Fire network and repeaters configuration 53 Basic configuration options 54 Advanced configuration options 55 Commissioning 59...
-
Page 31: The User Interface
Chapter 3: Configuration and commissioning The user interface Consult the operator manual for details on the different controls and indications provided by the control panel. User interface for two- and four-zone control panels Figure 16: User interface for two- and four-zone control panels Legend 1. -
Page 32: User Interface For Eight-Zone Control Panels
Chapter 3: Configuration and commissioning User interface for eight-zone control panels Figure 17: User interface for eight-zone control panels Legend 1. Zone buttons and LEDs (Z1, Z2, etc.) 12. Configuration controls 2. Supply LED 13. Reset button and LED 3. General Fault LED 14. -
Page 33: User Levels
Chapter 3: Configuration and commissioning Table 16: Regional variants of interface buttons and LEDs Item EN 54 NEN 2535 NBN S 21-100 Sounder Delay Fire Protection Fault/Disable/Test Evacuation Sounder Delay Reserved Fault Warning Fault/Disabled Reserved Sounder Start/Stop Sounder Start/Stop Evacuation Start/Stop Fire Routing Delay Fire Routing Delay Warning Sounder Delay... -
Page 34: Configuration Overview
Chapter 3: Configuration and commissioning User level passwords and indications The default user level passwords and the corresponding LED and seven- segment display indications are shown in the table below. The seven-segment display is only visible when the control panel cover is removed. See Figure 1 on page 6 and Figure 2 on page 7. - Page 35 Chapter 3: Configuration and commissioning Figure 18: Front panel configuration controls Button Function Scrolls to the next configuration menu on the seven-segment display. Scrolls to the next configuration value for the active menu on the seven-segment display. Scrolls to the previous configuration menu on the seven-segment display. Scrolls to the previous configuration value for the active menu on the seven-segment display.
-
Page 36: Common Configuration Tasks
Chapter 3: Configuration and commissioning Common configuration tasks To enter configuration mode: 1. Remove the control panel cover so that the seven-segment display is visible. 2. Enter a valid Installer user level password (3333 for basic configuration or 4444 for advanced configuration). 3. -
Page 37: Basic Configuration
Chapter 3: Configuration and commissioning Visual indications for current value and selected value Current and selected values are indicated as follows. Table 19: Visible indications for values Status Indication Current value Both decimal points on the display are steady New selected value Both decimal points on the display are flashing Other value Both decimal points on the display... - Page 38 Chapter 3: Configuration and commissioning Display Menu Values Operating mode EN 54-13 supervision ON/OFF EN 54-2 EN 54-2 Evacuation EN 54-2 Scandinavia NBN S 21-100 NEN 2535 Custom Panel mode EN 54-2 EN 54-2 Evacuation EN 54-2 Scandinavia BS 5839-1 (No 2nd stage) BS 5839-1 (2nd stage) NBN S 21-100 NEN 2535...
-
Page 39: Basic Default Configuration
Chapter 3: Configuration and commissioning Basic default configuration Use this menu to select common operating mode configuration presets. The default setting is 01 (EN 54-2, passive end-of-line). To select an operating mode configuration preset: 1. Set the display as shown below, and then press Enter. 2. -
Page 40: En 54-13 Supervision Mode
Chapter 3: Configuration and commissioning EN 54-13 supervision mode Use this menu to select the zone supervision mode (EN 54-13 supervision enabled or disabled). By default EN 54-13 zone supervision is disabled. Note: EN 54-13 supervision mode is not available in BS 5839-1 mode. To configure the supervision mode: 1. -
Page 41: Sounder Delay
Chapter 3: Configuration and commissioning Display Operating mode EN 54-2 Scandinavia BS 5839-1 (No second stage) BS 5839-1 (second stage) NBN S 21-100 NEN 2535 Custom See Appendix A “Configuration presets” on page 79 for presets and default settings for each operating mode. Custom operating mode A custom operating mode will be indicated if any of the following zone configuration settings are changed from the operating mode preset values:... - Page 42 Chapter 3: Configuration and commissioning Table 22: Default sounder delay values Operating mode Default delay in minutes EN 54-2 EN 54-2 Evacuation EN 54-2 Scandinavia BS 5839-1 NBN S 21-100 NEN 2535 This feature is not available in this operating mode. To configure a delay: 1.
-
Page 43: Fire Routing Delay
Chapter 3: Configuration and commissioning Fire routing delay Note: Use this menu to configure warning sounder delays in NBN S 21-100 mode. Use this menu to configure a fire routing delay of up to 10 minutes in operating modes where the feature is available. Default delays The default fire routing delay for each operating mode is shown below. -
Page 44: Extended Fire Routing Delay
Chapter 3: Configuration and commissioning Fire routing delay operation The delay applies to the activation of fire routing (if configured) only if all of the following are true: • The delay is enabled • The initiating device (detector or manual call point) is installed in an automatic zone (or the initiating device is a detector installed in a mixed zone) •... -
Page 45: Advanced Configuration
Chapter 3: Configuration and commissioning 4. Save your changes. Once configured the delay is enabled at the same time as the standard fire routing delay. A steady Fire Routing Delay LED indicates that all configured fire routing delays are enabled. Extended fire routing delay operation The same conditions required to apply a fire routing delay are applicable to apply an extended fire routing delay (i.e. -
Page 46: The Advanced Configuration Menu
Chapter 3: Configuration and commissioning The advanced configuration menu Configuration options for this menu are shown in Table 25 below. More information for each option is included in the related topic. Note: All configurable options included in “Basic configuration” on page 31 are also available from the advanced configuration menu. - Page 47 Chapter 3: Configuration and commissioning Display Menu Values Operating mode Fire network identifier 00 to 32 Software version Read-only Configuration version Read-only Configuration time stamp Read-only Configuration date stamp Read-only Zone configuration [1] Passive EOL Active EOL Unlatched Passive EOL with CleanMe Active EOL with CleanMe Intrinsically-safe Zone delay...
-
Page 48: Sounder Operation During A Zone Test
Chapter 3: Configuration and commissioning Display Menu Values Operating mode Control panel PCB serial Read only number Auxiliary 24 V reset ON/OFF Restore previous configuration Restore factory configuration N/A Exit without saving Exit and save [1] The CleanMe feature is available only with Aritech detectors. Sounder operation during a zone test Use this menu to configure the sounder operation during a zone test. -
Page 49: Sounder Re-Sound
Chapter 3: Configuration and commissioning Sounder re-sound Use this menu to configure the sounder re-sound, on or off. This determines sounder operation in a fire alarm event when sounders have been silenced by pressing the Sounder Start/Stop button and a new alarm event is reported. The default setting is ON. -
Page 50: Zone Configuration
Chapter 3: Configuration and commissioning In the time between the end of the configured disable time and the end of the configured sounder delay (when the Sounder Start/Stop LED is flashing), pressing the Sounder Start/Stop button silences sounders (before activation). A configured sounder delay may still be cancelled while the delay is running (and sounders activated) by pressing the Sounder Delay button. -
Page 51: Zone Delay
Chapter 3: Configuration and commissioning Display Description Passive end-of-line Active end-of-line [1] Unlatched (only available in BS 5839-1 mode) [1] Passive end-of-line with CleanMe [1][2][3] Active end-of-line with CleanMe [1][2][3] Intrinsically-safe zone [1][4] [1] Option not available if EN 54-13 supervision is enabled. [2] Option not available if operating mode is NEN 2535 [3] The CleanMe feature is available only with Aritech detectors. -
Page 52: Zone Type
Chapter 3: Configuration and commissioning — or — Select “others” to select the remote zones. The Zone alarm LED flashes fast to indicate that the corresponding zone configuration menu is active. 3. Select a value using the value selection buttons (2 and 4). 4. -
Page 53: Input Configuration
Chapter 3: Configuration and commissioning Display Description Mixed zone. The control panel automatically distinguishes between an automatic alarm (generated by a detector) and a manual alarm (generated by a manual call point fitted with a 100 Ω resistor). [1] Automatic zone. All fire alarms are treated as reported by a detector, even if the fire alarm is reported by a manual call point in the zone. -
Page 54: Changing User Level Passwords
Chapter 3: Configuration and commissioning Display Description Operating mode Extended fire routing delay EN 54-2 EN 54-2 Scandinavian Input active configures extended fire routing delay. NEN 2535 Fire routing inhibit delay EN 54-2 EN 54-2 Scandinavian Input active deactivates fire routing delays. NEN 2535 Class change Sounders are activated while the input is active... -
Page 55: Auxiliary 24 V Reset
Chapter 3: Configuration and commissioning To change the first two digits of a user level password: 1. Set the display for the desired user level password, and then press Enter. 2. Set the display as shown below, and then press Enter. 3. -
Page 56: Software, Configuration, And Serial Number Information
Chapter 3: Configuration and commissioning Software, configuration, and serial number information Use the corresponding menu option (shown below) to display software, configuration, and serial number information. These details may be required for troubleshooting and technical support. Software version (control panel, expansion board or fire network board) Configuration version Configuration time stamp... -
Page 57: Expansion Board Configuration
Chapter 3: Configuration and commissioning 3. Press Enter. 4. The software version is displayed in three consecutive segments, as shown below. Segment Description Example Is the major release identifier Is the minor release identifier Is the version cycle number In the above example, the reading is for software version 1.1.7. Expansion board configuration Adding an expansion board Use this menu, available from the basic or advanced configuration menus, to... -
Page 58: Expansion Board Configuration
Chapter 3: Configuration and commissioning Expansion board configuration Expansion board labels For configuration purposes expansion boards are labeled A and B (for two- and four-zone control panels) or A, B, C, and D (for eight-zone control panels). The label for a given module is defined by its position (left to right) in the control panel cabinet, The first expansion board installed is module A, the second B, etc. -
Page 59: Fire Network And Repeaters Configuration
Chapter 3: Configuration and commissioning The Expansion I/O Fault/Disabled LED on the control panel interface and the ON LED on the expansion board flashes fast to indicate that the module function configuration menu is active. 2. Select a value from 01 to 92 using the value selection buttons (2 and 4). 3. -
Page 60: Basic Configuration Options
Chapter 3: Configuration and commissioning settings). To display information for only that panel, press the Enter key for 3 seconds to provide a temporary, 30-second display of the local status indications. Basic configuration options The following table shows the options for creating basic fire network (firenet) configurations. -
Page 61: Advanced Configuration Options
Chapter 3: Configuration and commissioning 2. Select the number of control panels in the network. This is not required when you have two panels (i.e. a panel and a repeater). If you select 5, panel IDs 1 to 5 will have to be present so as not to have a network fault indication. - Page 62 Chapter 3: Configuration and commissioning Advanced configuration options for the fire network Display Description Value Firenet identifier 0 to 32 0: Stand-alone (no networking) Default: 0 Firenet number of nodes [1] 2 to 32 Default: 2 Firenet initial zone number when 0001 to 9999 the firenet repeater type (nr) = 2n The number has four digits.
- Page 63 Chapter 3: Configuration and commissioning Configuring firenet and repeater maps If the control panels in the system do not have all the node IDs numbered consecutively (starting from 1) or if the control panels do not repeat information from all other panels, then configure the nM (Firenet map) and rM (Firenet repeater map).
- Page 64 Chapter 3: Configuration and commissioning Examples: • A conventional repeater panel can repeat an analogue panel and many indications are not available for display. • A two-zone control panel could be configured to repeat an eight-zone panel. Zones 3 to 8 will not be available for display. Conventional systems can be configured to repeat control panels status information instead of zones status information, in the zone LED indications.
-
Page 65: Commissioning
Chapter 3: Configuration and commissioning Specify the firenet repeater type Select the firenet repeater type setting (nr) if you want to use the repeater to display panel status instead of zone status information. (nr = Pn). When the control panel is configured to repeat the status of other panels, the zone indications display global panel status information: the red zone LED will indicate the panel ID in the network is in alarm (automatic or manual) and the yellow zone LED will indicate the panel ID is in fault, disable or test. -
Page 66: Commissioning The Control Panel
Chapter 3: Configuration and commissioning • Polarity is observed for all sounder circuits and that all end-of-line resistors are installed, as described in “Connecting sounders or other notification devices to supervised outputs” on page 17 • Any optional equipment installed (fire routing, alarm, and fault relays, etc.) is correctly connected •... -
Page 67: Functional Tests
Chapter 3: Configuration and commissioning Battery startup To power up the control panel from the batteries, press the battery start button on the control panel PCB (marked as BAT. START, see Figure 20 below). Keep the button pressed for approximately 5 seconds. Figure 20: Battery startup button Functional tests Create a short and open circuit in the zone to test fault reporting for each. - Page 68 Chapter 3: Configuration and commissioning Event Response time Network fault Less than 100 seconds Earth fault Less than 100 seconds Battery charger fault Less than 100 seconds No batteries found fault Less than 3 minutes Mains fault Less than 3 minutes Out of service fault Less than 100 seconds Fuse/protection fault...
-
Page 69: Maintenance
Chapter 4 Maintenance Summary This chapter includes information on fire alarm system maintenance and battery maintenance. Content Fire alarm system maintenance 64 Quarterly maintenance 64 Annual maintenance 64 Cleaning the control panel 64 Battery maintenance 64 SynaG Series Installation Manual... -
Page 70: Fire Alarm System Maintenance
Chapter 4: Maintenance Fire alarm system maintenance Perform the following maintenance tasks to ensure that the fire alarm system works correctly and complies with all required European regulations. Note: Before performing any tests, ensure that fire routing (if configured) is disabled or that the fire brigade has been notified. - Page 71 Chapter 4: Maintenance Troubleshooting batteries Battery supply and battery fuse faults are indicated by a flashing Supply Fault LED. If this LED is flashing, check the following: • That the battery cables are in good condition • That the battery cables are connected securely and correctly at the battery and at the control panel PCB If the cables are in good condition and all connections are correct, then the batteries should be replaced immediately.
- Page 72 Chapter 4: Maintenance SynaG Series Installation Manual...
-
Page 73: Technical Specifications
Chapter 5 Technical specifications Summary This chapter includes technical specifications for your fire alarm control panel. Content Zone specifications 68 Input and output specifications 69 Power supply specifications 71 Mechanical and environmental specifications 72 Fire network specifications 73 Cabinet drawings and dimensions 74 SynaG Series Installation Manual... -
Page 74: Zone Specifications
Chapter 5: Technical specifications Zone specifications Table 30: General zone specifications Zone circuit output voltage Nominal 22 VDC Maximum 24 VDC Minimum 18 VDC Maximum current consumption per zone circuit 65 mA Default zone circuit configuration EN 54 Passive end-of-line NEN 2535 Passive end-of-line NBN S 21-100... -
Page 75: Input And Output Specifications
Chapter 5: Technical specifications Open circuit reference range Zone impedance > 8 kΩ 2.6 mA Zone device current consumption [1] Mixed zones are not allowed on installations requiring EN 54-13 compliance or intrinsically- safe zones Table 32: Automatic and manual zone specifications Standard / EN 54-13 Intrinsically safe... - Page 76 Chapter 5: Technical specifications Table 34: Supervised inputs [1] Cable resistance Short circuit ≤ 220 Ω Active < 220 Ω to 8 kΩ High-impedance fault < 8 kΩ to 10 kΩ Standby < 10 kΩ to 20 kΩ Open circuit >...
-
Page 77: Power Supply Specifications
Chapter 5: Technical specifications Power supply specifications Table 36: Mains supply specifications Operating voltage 110 VAC / 60 Hz or 240 VAC / 50 Hz Rated current (two- and four-zone control panels) 110 VAC 240 VAC Rated current (eight-zone control panels) 110 VAC 3.15 A 240 VAC... -
Page 78: Mechanical And Environmental Specifications
Chapter 5: Technical specifications Table 39: Control panel current consumption specifications (EN 54-4) Min. current consumption (Imin) [1] Two-zone control panels 0.042 A Four-zone control panels 0.051 A Eight-zone control panels 0.069 A Max. current consumption in standby (Imax a) Two-zone control panels 0.30 A Four-zone control panels... -
Page 79: Fire Network Specifications
Chapter 5: Technical specifications Fire network specifications Table 42: Fire network specifications Maximum distance between 1.2 km control panels Maximum capacity 32 nodes and 64 zones Communication protocol Proprietary peer-to-peer protocol based on RS-485 SynaG Series Installation Manual... -
Page 80: Cabinet Drawings And Dimensions
Chapter 5: Technical specifications Cabinet drawings and dimensions Figure 21: Two- and four-zone cabinet with cover SynaG Series Installation Manual... - Page 81 Chapter 5: Technical specifications Figure 22: Two- and four-zone cabinet without cover SynaG Series Installation Manual...
- Page 82 Chapter 5: Technical specifications Figure 23: Eight-zone cabinet with cover SynaG Series Installation Manual...
- Page 83 Chapter 5: Technical specifications Figure 24: Eight-zone cabinet without cover SynaG Series Installation Manual...
- Page 84 Chapter 5: Technical specifications SynaG Series Installation Manual...
-
Page 85: Appendix A Configuration Presets
Appendix A Configuration presets Summary This appendix includes detailed information on operating mode and expansion board configuration presets. Content Operating mode presets 80 EN 54-2 presets 80 EN 54-2 Evacuation 81 EN 54-2 Scandinavia 82 BS 5839-1 83 NBN S 21-100 84 NEN 2535 85 Expansion board presets 86 SynaG Series Installation Manual... -
Page 86: Operating Mode Presets
Appendix A: Configuration presets Operating mode presets EN 54-2 presets Table 43: Configuration presets Preset Control EOL type Output Sounder Fire routing Zone type panel type outputs outputs Two-zone Passive Class B Mixed Four-zone, Passive Class B Mixed eight-zone Two-zone Passive, Class B Mixed... -
Page 87: En 54-2 Evacuation
Appendix A: Configuration presets EN 54-2 Evacuation Table 46: Configuration presets Preset Control panel EOL type Output type Sounder Zone type outputs Two-zone Passive Class B Mixed Four-zone, Passive Class B Mixed eight-zone Two-zone Passive, Class B Mixed CleanMe enabled [1] Four-zone, Passive, Class B... -
Page 88: En 54-2 Scandinavia
Appendix A: Configuration presets EN 54-2 Scandinavia Table 49: Configuration presets Preset Control EOL type Output Sounder Fire routing Zone type panel type outputs outputs Two-zone Passive Class B Mixed Four-zone, Passive Class B Mixed eight-zone Two-zone Passive, Class B Mixed CleanMe enabled [1]... - Page 89 Appendix A: Configuration presets BS 5839-1 Table 52: Configuration presets Preset Control panel EOL type Output type Sounder Zone type outputs [1] Two-zone Active Class B 2 (stage 1 “Alert”) Mixed Four-zone, Active Class B 4 (stage 1 “Alert”) Mixed eight-zone Two-zone Active, CleanMe...
-
Page 90: Nbn
Appendix A: Configuration presets NBN S 21-100 Table 55: Configuration presets Preset Control EOL type Output Warning Evacuation Zone type panel type sounder sounder outputs outputs Four-zone, Passive Class B Odd: Automatic eight-zone Even: Manual Four-zone, Passive, Class B Odd: Automatic eight-zone CleanMe Even: Manual... -
Page 91: Nen 2535
Appendix A: Configuration presets NEN 2535 Table 58: Configuration presets Preset Control EOL type Output Sounder Fire routing Zone type panel type outputs outputs Four-zone, Passive Class B Odd: Automatic eight-zone Even: Manual Four-zone, EN 54-13 Class A Odd: Automatic eight-zone supervision Even: Manual... -
Page 92: Expansion Board Presets
Appendix A: Configuration presets Expansion board presets The following tables include the display settings for relay and supervised output expansion board configuration presets. Table 61: Expansion board zone configuration with EN 54-13 supervision disabled Display Zone Output Delay Display Zone Output Delay 1 and 2... - Page 93 Appendix A: Configuration presets Display Event Output Delay Display Event Output Delay Fault Alarm Reset on Fault Alarm 34 [2] Fire Routing Fault (Auto) Buzzer on 3 Fire routing (Manual) Reset Fault [1] 35 [2] Fire routing 1 Alarm Fault [1] Fault warning output [3]...
- Page 94 Appendix A: Configuration presets Table 63: Expansion board sounder circuit configuration with EN 54-13 supervision disabled [1] Display Events Output Delay 90 [2] Evacuation sounders Warning sounders Sounders (Evacuation sounders for NBN S 21-100) 92 [2] Warning sounders [1] These presets are only available for supervised expansion boards. [2] NBN S 21-100 only Table 64: Expansion board zone configuration with EN 54-13 supervision enabled Display...
- Page 95 Appendix A: Configuration presets Display Event Outputs Delay Display Event Outputs Delay 3 and 4 Reset on 3 and 4 Alarm 1 and 2 34 [2] Fire routing 1 and 2 (auto) Fault 3 and 4 Fire routing 3 and 4 (manual) Fault [1] 1 and 2...
- Page 96 Appendix A: Configuration presets SynaG Series Installation Manual...
-
Page 97: Appendix B Product Compliance
Appendix B Product compliance Summary This appendix contains regulatory information that applies to your control panel. Content European standards 92 Construction Products Directive (CPD) 93 SynaG Series Installation Manual... -
Page 98: European Standards
Appendix B: Product compliance European standards European standards for fire control and indicating equipment These control panels have been designed in accordance with European EN 54-2, EN 54-4, BS 5839-1, NBN S 21-100, and NEN 2535 standards. In addition, all models comply with the following EN 54-2 optional requirements. Table 67: European standards Option Description... -
Page 99: Construction Products Directive (Cpd)
Appendix B: Product compliance Construction Products Directive (CPD) Certification Certification body 0832 Certificate numbers SG2000, SG2000SC 0832-CPD-1745 SG4000, SG4000SC 0832-CPD-1746 SG8000, SG8000SC 0832-CPD-1747 Year of manufacture The year and day of manufacture, in the format YYDDD, is included in the first five digits of your product serial number (located on the product identification label) Manufacturer UTC Fire &... - Page 100 Appendix B: Product compliance SynaG Series Installation Manual...
-
Page 101: Index
Index A connecting fire routing equipment to supervised outputs, 17 adding a fire network board, 39 connecting inputs, 14 adding an expansion board, 51 connecting manual call points, 13 adding expansion boards, 39 connecting sounders or other notification advanced configuration, 39 devices to supervised outputs, 17 advanced configuration menu, 40 connecting supervised inputs, 15... - Page 102 Index fixing the cabinet to the wall, 8 selecting processing for remote zones in functional tests, 61 alarm, 58 selecting the loop class, 58 I seven-segment display, 29 software compatibility, ii important information, ii software, configuration, and serial number input and output specifications, 69 information, 50 input configuration, 47 sounder delay, 35...