Christie DWU951 Service Manual page 44

DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P)
7KH FXUUHQW VWDWXV
In a normal state
The Status Monitor displays the state of the projector in three lines.
: Displays the condition of the projector. While the lamp is on, the selected port is displayed.
1st line
Displayed conditions are as below;
STANDBY: The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN: The projector is cooling down.
: Displays the condition of the detected input signal while the lamp is on. Otherwise, displays the
2nd line
serial number of the projector.
Displayed conditions are as below;
SYNC OUT 'HWHFWHG LQSXW VLJQDO LV RXW RI VSHFL¿HG UDQJH
NO SIGNAL: There is no input signal.
CONNECTED 7KH SURMHFWRU KDV FRQQHFWHG WR WKH QHWZRUN RU WKH FRPSXWHU DQG VRPH LPDJH LV
transferred to the projector while the LAN is selected.
HOLD: 7KH SURMHFWRU KDV FRQQHFWHG WR WKH QHWZRUN EXW QR LPDJH LV WUDQVIHUUHG ZKLOH WKH /$1 SRUW LV VHOHFWHG
NOT CONNECTED: 7KH SURMHFWRU LV QRW FRQQHFWHG WR WKH QHWZRUN RU WKH FRPSXWHU ZKLOH WKH /$1 SRUW LV VHOHFWHG
: Displays supplied voltage and peripheral temperature in Celsius while the lamp is on.
3rd line
NOTE: ‡ :KLOH WKH SURMHFWRU LV VHDUFKLQJ DQ LQSXW VLJQDO LQ QRUPDO FRQGLWLRQ QRWKLQJ LV GLVSOD\HG
on the 2nd line of the monitor.
‡ 'LVSOD\HG WHPSHUDWXUH PD\ EH GLIIHUHQW IURP DFWXDO SHULSKHUDO WHPSHUDWXUH EHFDXVH WKH GLVSOD\HG
temperature is measured inside the projector.
Warnings and Errors
The Status Monitor displays a warning or an error with larger letters when it is detected. Refer to
the table on the next page for the correspondence among the displays of the Status Monitor and
indicator lamps and how to cope with it.
Warnings;
AIR (AIR FLOW): The internal temperature is rising.
COLD: The inside of the projector is cooled excessively.
FILTR ,W LV WLPH WR FOHDQ WKH DLU ¿OWHU
SHUTR: The mechanical shutter does not open.
SHIFT 7KH PHFKDQLFDO OHQV VKLIW GRHV QRW ZRUN
LAMP1: Lamp 1 does not light.
LAMP2: Lamp 2 does not light.
HUMID: Humidity is too high.
C.WHL: One of the color wheels is out of order.
Errors;
&29(5 7KH ODPS FRYHU KDV QRW EHHQ ¿[HG SURSHUO\
FAN: The cooling fan is not operating.
LAMP: Neither lamp lights.
TEMP: The inside of the projector is overheating.
OTHER: Miscellaneous error in the ENGINE assembly is detected.
NOTE: ‡ 7KH EDFNOLJKW EOLQNV ZKHQ DQ HUURU LV GLVSOD\HG
Error (and warning) log
3UHVV WKH EXWWRQ WR GLVSOD\ SUHYLRXV HUURU ORJ ZKHQ WKH FXUUHQW VWDWXV LV GLVSOD\HG ZLWK WKH
EDFNOLJKW RQ 8S WR  HUURU ORJV FDQ EH GLVSOD\HG 7KH ORJ FRQWDLQV WKH ORJ QXPEHU RFFXUUHG HUURU
WKH VXSSOLHG YROWDJH DQG SHULSKHUDO WHPSHUDWXUH DW WKDW WLPH 3UHVV WKH
usage time in the Lamp log and the Filter log when each error occurred.
NOTE:
‡ If no error or less than 10 errors have occurred, "NO DATA" is displayed in spite of occurred error in the error log.
‡ Refer to the table on the next page for the correspondence among the displays of the Status Monitor and indicator lamps.
DWU951/DWX951/DXG1051 Service Manual
020-000674-01 Rev.1 (01-2014)
42
EXWWRQ WR GLVSOD\ WKH
Page 42 / 118