Christie DWU951 Service Manual page 35

DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P)
6-11 Related Messages
:KHQ VRPH PHVVDJH DSSHDUV FKHFN DQG FRSH ZLWK LW DFFRUGLQJ WR WKH IROORZLQJ WDEOH
Although these messages will be automatically disappeared in about several minutes, it will be
reappeared every time the power is turned on.
Message
DWU951/DWX951/DXG1051 Service Manual
020-000674-01 Rev.1 (01-2014)
There is no input signal.
3OHDVH FRQ¿UP WKH VLJQDO LQSXW FRQQHFWLRQ DQG WKH VWDWXV RI WKH VLJQDO VRXUFH
3URMHFWRU LV ZDLWLQJ IRU DQ LPDJH ¿OH
&KHFN WKH KDUGZDUH FRQQHFWLRQ VHWWLQJV RQ WKH SURMHFWRU DQG QHWZRUN
related settings.
7KH FRPSXWHU3URMHFWRU QHWZRUN FRQQHFWLRQ PLJKW EH GLVFRQQHFWHG 3OHDVH
re-connect them.
The horizontal or vertical frequency of the input signal is not within
WKH VSHFL¿HG UDQJH
3OHDVH FRQ¿UP WKH VSHFV IRU \RXU SURMHFWRU RU WKH VLJQDO VRXUFH VSHFV
An improper signal is input.
3OHDVH FRQ¿UP WKH VSHFV IRU \RXU SURMHFWRU RU WKH VLJQDO VRXUFH VSHFV
The internal temperature is rising.
Turn the power off, and wait at least 20 minutes. After the projector has
VXI¿FLHQWO\ FRROHG GRZQ FKHFN WKH IROORZLQJ LWHPV DQG WKHQ WXUQ WKH
power on again.
‡ ,V WKHUH EORFNDJH RI WKH DLU SDVVDJH DSHUWXUH"
‡ ,V WKH DLU ¿OWHU GLUW\" ,I VR SOHDVH FOHDQ RU UHSODFH WKH DLU ¿OWHU
‡ 'RHV WKH DPELHQW WHPSHUDWXUH H[FHHG VSHFL¿HG UDQJH" 5HIHU WR WKH
chapter 6SHFL¿FDWLRQV.)
‡ ,V WKH VHWWLQJ IRU $/7,78'( DSSURSULDWH"
( For details of ALTITUDE, refer to the User's Manual. The wrong setting
of ALTITUDE may cause damage to the projector itself.)
‡ ,V WKH KRWFROG DLU IURP SHULSKHUDO HTXLSPHQW EORZLQJ DJDLQVW WKH LQWDNH
vents of projector?
The internal humidity is rising.
&KHFN LI WKH DPELHQW KXPLGLW\ LV XQGHU 
condensation. Too much humidity hinders cooling performance of ENGINE
assembly, and furthermore, may cause dew condensation inside the
FRPSRQHQW DQG EUHDN GRZQ
$ QRWH RI SUHFDXWLRQ ZKHQ FOHDQLQJ WKH DLU ¿OWHU
3OHDVH WXUQ WKH SRZHU RII DQG FOHDQ RU FKDQJH WKH DLU ¿OWHU UHIHUULQJ WR WKH
&OHDQLQJ DQG UHSODFLQJ WKH DLU ¿OWHU section of this manual. After you
KDYH FOHDQHG RU FKDQJHG WKH DLU ¿OWHU SOHDVH EH VXUH WR UHVHW WKH ¿OWHU
hours.
The LENS ID cannot be recognized.
3OHDVH WXUQ WKH SRZHU RII DQG FKHFN LI SURSHU /(16 LV XVHG QR GXVW RU
distortion in the BtoB connectors, and all the cable connections.
If the same massage is displayed, replace the LENS, whole ENGINE
assembly or MAIN PCB.
The button operation is not available.
&KHFN WKH EXWWRQ \RX DUH JRLQJ WR XVH (YHQ ZKHQ D XVDEOH EXWWRQ LV
pressed, all button operations are not available under the following conditions.
‡ While the lens is moving, button operation from the control panel or the
remote control might be ignored.
‡ Pressing one of the buttons to call a signal input might be ignored (set at
SOURCE SKIP of the OPTION menu).
33
Description
DQG WKHUH LV QR GHZ
Page 33 / 118