DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 1. Features ! $GYDQFHG 1HWZRUN )XQFWLRQV Not only can you control and monitor the projectors via LAN connection, but also project still or PRYLQJ LPDJHV IURP RQH RU PRUH QHWZRUNHG FRPSXWHUV ! :LUHOHVV 1HWZRUN &DSDELOLW\ <RX FDQ XVH WKH ZLUHOHVV QHWZRUN E\ FRQQHFWLQJ WKH SURMHFWRU WR D 3&...
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) $GMXVWPHQW 4-1 Before adjusting 4-1-1 Selection of adjustment When any parts in the table below are changed, choose the proper adjusting items with the chart. In addition, setup of the projector according to the chapter 4-5 by service engineers or users is recommended after all adjustments are done.
Page 9
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 4-2 AIR SENSOR adjustment When you replaced the MAIN PCB, SENSOR-A/ Adjustment procedure B PCB or BALLAST FAN, or when you re- 1. Display the A-SENS bar with the DWWDFKHG RQH RI WKH %$//$67 +2/'(5V PDNH buttons in FACTORY MENU - VID-AD1.
Page 10
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 4-4 LENS SHIFT adjustment When you replaced the ENGINE assembly Adjustment procedure 1. Display the LENS_C bar with the or MAIN PCB, make sure to carry out this buttons in FACTORY MENU - OPTION. (Example adjustment after re-assembling the projector.
Page 11
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 4-5 Setup of the projector FOCUS + / - Following contents are also described in User's manual. buttons z Adjusting the zoom and focus 1. The ZOOM or FOCUS dialog will appear when you press any of the...
Page 13
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Power cannot turn on. *: Be sure to unplug the power cord before measuring resistance. voltage Measure Replace MAIN PCB. § 0 supplied at pins (5) and resistance* between (7) of E800 on the MAIN pins (5) and (7) of Replace POWER UNIT CIRCUIT1.
Page 14
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Neither lamp lights. Does Replace MAIN PCB. the Status Monitor displaying any error Replace STATUS MONTOR. message? &KHFN OTHER the error message Replace ENGINE ass’y. displayed in the Status Monitor. The other of OTHER &KHFN HDFK ÀRZ DV EHORZ...
Page 15
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) LAMP ERROR is detected. &KHFN LI the LAMP UNITs are Re-install LAMP UNITs. installated correctly. Does the voltage of the pins (7) and (9) of Replace MAIN PCB. ET02 of MAIN PCB change...
Page 16
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) FAN ERROR is detected. *: FAN1: LAMP 1 EXHAUST FAN FAN2: LAMP 1 UP FAN FAN3: LAMP 1 DOWN FAN FAN4: LAMP 2 EXHAUST FAN FAN5: LAMP 2 UP FAN FAN6: LAMP 2 DOWN FAN...
Page 17
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Picture is not displayed correctly via COMPUTER IN ports. Turn on PbyP or PIP and select Replace IS01 : THS7327PHPR. HDMI 1 as the sub area. The picture on the main Replace MAIN PCB.
Page 18
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Picture is not displayed correctly via wired/wireless* LAN. *: The USB wireless adapter is needed to use wireless LAN. communicate via wireless or &KHFN WKH ÀRZ RQ SDJH ZLUHG QHWZRUN"...
Page 19
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Picture is not displayed correctly via VIDEO port. whether changing INPUT PCB can Replace MAIN PCB. ¿[ WKH SUREOHP Replace INPUT PCB. Signal from MONITOR OUT port is not displayed correctly. the projector display picture correctly &KHFN WKH ÀRZ RQ SDJH ...
Page 20
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Focus or zoom adjustment cannnot be operated. *: Be sure to unplug the power cord before measuring resistance. &KHFN any dust or distortion in the BtoB Clean the connectors with air duster.
Page 21
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) &DQQRW FRPPXQLFDWH YLD ZLUHG QHWZRUN Does the Is the Set the STANDBY MODE LED on lower right of STANDBY MODE setting as “NORMAL” in the SETUP the LAN port light in “NORMAL”? menu.
Page 22
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) &DQQRW FRPPXQLFDWH YLD ZLUHOHVV QHWZRUN Is the USB wireless adapter connected Re-connect the USB wireless adapter properly. properly? Wait more than 1 minute after the adapter is connected. Is LED on WKH DGDSWHU EOLQNLQJ"...
Page 23
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 7URXEOHVKRRWLQJ IRU RWKHU 1HWZRUN SUREOHPV Problem /LNHO\ &DXVH 7KLQJV WR &KHFN The projector is not turned on. Is the projector’s lamp on? No image The projector’s input source isn’t Is the LAN port selected? switched properly.
Page 24
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Troubleshooting for other Network problems (continued) Problem /LNHO\ &DXVH 7KLQJV WR &KHFN 7KH /LYH9LHZHU GRHV QRW ZRUN RQ Can't Install $SSO\ WKH ODWHVW 6HUYLFH 3DFN WR \RXU Windows Vista without any Service "LiveViewer"...
Page 25
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6HUYLFH SRLQWV 6-1 Lead free solder [CAUTION] This product uses lead free solder (unleaded) to help preserve the environment. Please read these LQVWUXFWLRQV EHIRUH DWWHPSWLQJ DQ\ VROGHULQJ ZRUN CAUTION Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead IUHH VROGHU FDQ VSODWWHU DW KLJK WHPSHUDWXUHV Û&...
Page 26
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-2 Articles necessary to your maintenance and repair works In this projector, adhesive tapes and cable ties are used for the purpose of fastening and tying the wires. Once you remove the tapes or unfasten the cable ties, you may not reuse them. We recommend you to prepare such articles, in advance.
Page 27
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-4 Installing the Batteries WARNING Always handle the batteries with care and use them only as directed. Improper use may result LQ EDWWHU\ H[SORVLRQ FUDFNLQJ RU OHDNDJH ZKLFK FRXOG UHVXOW LQ ¿UH LQMXU\ DQGRU SROOXWLRQ RI WKH surrounding environment.
Page 29
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-6 Lamp Lamp warning WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE 7KH SURMHFWRU XVHV D KLJKSUHVVXUH PHUFXU\ ODPS 7KH ODPS FDQ EUHDN ZLWK D ORXG EDQJ RU burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Page 30
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Replacing the LAMP UNIT $ ODPS KDV ¿QLWH SURGXFW OLIH 8VLQJ WKH ODPS IRU ORQJ SHULRGV RI WLPH FRXOG FDXVH WKH SLFWXUHV GDUNHU or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Page 31
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-7 Other care WARNING %HIRUH FDULQJ PDNH VXUH WKH SRZHU FDEOH LV QRW SOXJJHG LQ DQG WKHQ DOORZ WKH SURMHFWRU WR FRRO VXI¿FLHQWO\ 7KH FDUH LQ D KLJK WHPSHUDWXUH VWDWH RI WKH SURMHFWRU FRXOG FDXVH D EXUQ DQGRU malfunction to the projector.
Page 32
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-8 Notice of AUTO adjustment Use of AUTO adjustment with the image through analog RGB input optimizes V_POSI, H_POSI, and H_PHASE automatically. ,Q FDVH WKDW GLVSOD\ LPDJH KDV GDUN WRQH DURXQG LWV SHULSKHUDO $872 RSHUDWLRQ VRPHWLPHV PDNHV artifacts in the image, shifts capture area and so on.
Page 33
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-9 How to inactivate the security functions This projector is equipped with security functions as below. (1) My Screen PASSWORD The My Screen PASSWORD function can be used to prohibit access to the My Screen function and prevent the currently registered My Screen image from being overwritten.
Page 34
Inquiring Code PIN BOX (ID Inquiring Code) 2. Send CHRISTIE servicing provider the Inquiring code (10 digits) to inquire the correct PIN code. 3. While the PIN BOX is displayed, enter the correct PIN Code that CHRISTIE servicing provider informed.
Page 35
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-11 Related Messages :KHQ VRPH PHVVDJH DSSHDUV FKHFN DQG FRSH ZLWK LW DFFRUGLQJ WR WKH IROORZLQJ WDEOH Although these messages will be automatically disappeared in about several minutes, it will be reappeared every time the power is turned on.
Page 36
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-12 Regarding the indicator lamps 7KH LQGLFDWRUV PD\ GLIIHU IURP XVXDO FKHFN DQG FRSH ZLWK LW DFFRUGLQJ WR WKH IROORZLQJ WDEOH The indicators are described as below. %OLQNLQJ Don't care Steady light...
Page 38
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Regarding the indicator lamps (continued) Indicator Status Description Projector has detected LAMP2 WARNING. The LAMP2 UNIT is turned off. Turn the power off, and wait at least for 45 PLQXWHV $IWHU WKH SURMHFWRU KDV VXI¿FLHQWO\ FRROHG GRZQ WU\ WXUQLQJ RQ WKH projector.
Page 39
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Regarding the indicator lamps (continued) Indicator Status Description <HOORZ PIN LOCK function is active. Please refer to the section How to inactive the security functions and PIN LOCK System, or the chapter SECURITY menu in the User's Manual.
Page 40
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-13 HIDDEN SERVICE MENU With the control panel With the remote control 1. Press the MENU button to 1. Press the MENU button to display the ADVANCED MENU. display the ADVANCED MENU.
Page 41
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-14 RUN TIME window z The product operating time display method (accumulated lamp time display method) 1. Open the ADVANCED MENU and select SETUP - LAMP & FILTER - LAMP-1 HOURS or LAMP-2 HOURS, and then press the , ENTER or RESET button to display the LAMP TIME reset box.
Page 42
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-16 Reset of the Network Web password / User ID, Network Control password ATTENTION 3HUIRUPLQJ WKLV RSHUDWLRQ LQLWLDOL]HV WKH QHWZRUN VHWWLQJV ,I WKH SURMHFWRU KDV WKH FXVWRPL]HG VHW- WLQJV LQ WKH QHWZRUN PDNH D QRWH RI WKH QHWZRUN VHWWLQJV WR UHVWRUH WKHP EHIRUH WKLV RSHUDWLRQ 1.
Page 43
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-17 Status Monitor The Status Monitor is the sub LCD in the side panel that displays the Status Monitor information in the following. &XUUHQW VWDWXV RI WKH SURMHFWRU (UURU ORJ ...
Page 44
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 7KH FXUUHQW VWDWXV In a normal state The Status Monitor displays the state of the projector in three lines. : Displays the condition of the projector. While the lamp is on, the selected port is displayed.
Page 45
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) :KHQ &XUUHQW 6WDWXV DQG /RJ RQ 6WDWXV 0RQLWRU GLVSOD\V GLIIHUV IURP XVXDO FKHFN DQG FRSH ZLWK LW according to the following table. Status Monitor Indicator Description current Front Front Rear Rear...
Page 46
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Lamp log Displays the usage time of the lamp1 & 2, and executes Lamp Time Reset. You can display SUHYLRXV ORJV E\ SUHVVLQJ WKH EXWWRQ Usage time; z Displays remaining cycle time and the lamp 1 & 2 usage time.
Page 47
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 6-18 Lens installation / removal procedures /HQV ,QVWDOODWLRQ 3URFHGXUH Caution 1. Pull out the dust protector knobs to remove it. ,QVWDOOLQJ WKH OHQV LQ WKH SURMHFWRU ZLWK WKH OHQV FDS RQ PD\ OHDG WR PDOIXQFWLRQ $YRLG KLWWLQJ WKH VXUIDFH RI WKH OHQV RQ WKH SURMHFWRU ZKHQ DWWDFKLQJ WKH OHQV DV this may lead to malfunction.
Page 48
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) /HQV 5HPRYDO 3URFHGXUH $GMXVWPHQW RI 8OWUD VKRUW WKURZ ]RRP OHQV 86/&+ 7KH IRFXV EDODQFH IURP WKH FHQWHU WR VXUURXQGLQJ DUHD YDULHV RQ WKH VFUHHQ VL]H 1. Return the lens shift to the center position 7KH 8OWUD VKRUW WKURZ ]RRP OHQV KDV D IRFXV DGMXVWPHQW IXQFWLRQ WR DGMXVW WKLV EDODQFH (1) Press the /(16 6+,)7 button.
Page 51
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Notice _______________________________________________________________________ CAUTION assembling. Pay attention not to damage the wires or any other fragile parts of the projector. Be sure to lock the connectors which has locking mechanism. (Push in until it clicks.) ...
Page 52
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Assembling 1. Make sure the direction, and put the LAMP EXHAUST FAN on the LAMP DOOR. Make the labeled side face LAMP DOOR (outside), and pull out the fan cable from the side near the other lamp cover assembly.
Page 53
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) UPPER CASE (UPPER CASE, FRONT COVER) NOTE: Remove the LENS unit before disasembling the UPPER CASE. Refer to the section Lens installation / removal procedures of the chapter Service points about assembling/disassembling LENS unit (and front cover).
Page 54
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) z As replacement of UPPER CASE Put the rib on the UPPER Remember to detach the shading sheets and re-use CASE into the slot of the them with new UPPER CASE. The service parts does VKDGLQJ VKHHW WR ¿[ LW...
Page 55
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 0$,1 3&% EORFN 0$,1 ,1387 .(<3$' 68% /&' 3&% 67$786 021,725 &21752/ %87721 ,2 &29(5 86% 0,1, &29(5 Disassembling Assembling 1. Disconnect all the cables from the MAIN 1. Check the wiring if it is properly prepared.
Page 56
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Wiring %HIRUH DWWDFKLQJ WKH 0$,1 3&% EORFN Check the wiring around the MAIN PCB block before attaching the MAIN PCB block for preparing. <Side of power unit circuit case> Lead CNPW2 upward.
Page 57
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) $IWHU DWWDFKLQJ WKH 0$,1 3&% EORFN Connect and wire all the cables to be connected to the MAIN PCB as below. The cables with pale blue frame and pointing arrow are from ENGINE assembly.
Page 58
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Rear side of the MAIN PCB Wire the cables in the area surrounded with yellow dotted line according to WKH following procedure. 1. Connect and style Connect CNPW1. Connect CNPW2. CNPW1 and CNPW2.
Page 59
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) ENGINE (left) side of the MAIN PCB Wire the cables in the area surrounded with orange dotted line according to WKH following procedure. 6W\OH &1675 DQG &1/$' DQG FRQQHFW OHQV VKLIWB+ PRWRU FDEOH OHQV VKLIWB9 PRWRU FDEOH CNDCR, CNLAD, CNSTR and IRIS UNIT cable.
Page 60
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 3. Connect CNHS. Bandle LAMP2 UP FAN cable, temperature sensor cable and CNCWC with the ferrite core, and connect them. Connect CNHS. LAMP2 UP FAN cable. Connect temperature sensor cable. Connect CNCWC.
Page 61
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) z I/O COVER, USB MINI COVER Disassembling M3x8, black screw, torque: 0.39~0.59N·m 1) Remove a screw to detach USB MINI COVER. 2) Remove a screw and release 4 hooks on the I/O COVER from the I/O METAL.
Page 62
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Assembling 1) Check the direction and attach the 4 harnesses to MAIN PCB. 2) ,1387 3&%! 3XW WKH ,1387 3&% WRJHWKHU ZLWK WKH ,2 0(7$/ DQG fasten 6 screws as before. 0$,1 3&%! Put the MAIN PCB in place of the block, and fasten 11 VFUHZV DQG 86% 0,1, &29(5 DV EHIRUH...
Page 64
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) /$03 (;+$867 '8&7 (LAMP DOOR RELAY PCB) Disassembling 1. Disconnect all the harnesses from the LAMP DOOR RELAY PCB. 2. Remove a screw from the power unit LAMP EXHAUST DUCT Power unit circuit case circuit case which secures the earth cable CNGD2.
Page 65
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) /$03 +286( /$03 6: 3&% 7KHUPDO VZ 76: NOTE: Remove the LAMP EXHAUST DUCT before disassembling the LAMP HOUSEs. Disassembling TSW2, TSW1 (thermal sw.) LAMP2 HOUSE (R) CNLP2 LAMP1 HOUSE (L) 1. Pull out the thermal sw.
Page 66
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) $IWHU DWWDFKLQJ WKH /$03 +286(V :LUH &1/3 &1&6 DQG WKHUPDO VZ FDEOHV &176 Put CNCS2 on top of other cables. as below. Do not pass CNCS2 Pass CNCS2 through through this clamp.
Page 67
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) POWER UNIT HOLDER NOTE: T3x12, black screw, torque: 0.68~0.88N m Remove the MAIN PCB block before disassembling the POWER UNIT HOLDER. AC holder Disassembling Remove 2 screws, and pull the POWER UNIT HOLDER up.
Page 68
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) (1*,1( DVVHPEO\ (1*,1( DVVHPEO\ $'$37(5 3&% /$03 83 )$1 6+877(5 81,7 NOTE: 5HPRYH WKH /$03 81,7V CW UP EXHAUST DUCT, MAIN PCB block, LAMP EXHAUST DUCT, LAMP HOUSEs and POWER UNIT HOLDER before detaching the ENGINE assembly.
Page 69
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Wiring %HIRUH DWWDFKLQJ WKH (1*,1( DVVHPEO\ Check the wiring around the ENGINE assembly before attaching the ass'y unit for preparing. DC RELAY PCB Pass the IRIS fan cable on the duct side of the boss.
Page 70
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) z $'$37(5 3&% Connect CNLAD. NOTE: It is not necessary to detach ENGINE assembly before detaching the ADAPTER PCB. Disassembling Disconnect the cable CNLAD, and remove 2 screws to detach ADAPTER PCB.
Page 72
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) BALLAST UNIT (BALLAST FAN, POWER UNIT1/2 BALLAST, SENSOR-A/B PCB, DC RELAY PCB) Disassembling 1) Disconnect all the remained cables on the DC RELAY PCB, remove 2 screws to detach the PCB. 2) Remove 2 screws to detach the ballast shield.
Page 73
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Ballast cover (BALLAST FAN) Disassembling 1) Remove 4 screws to detach the ballast cover. Put away CNBL2 and BALLAST FAN cable from the holes on the ballast cover carefully. 2) Remove the BALLAST FAN.
Page 74
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Ballast holder Slide the holder Disassembling 1) Remove 4 screws and slightly CNPF1 lift and slide the ballast holder. 2) Remove 2 screws to detach the ballast cable shield. 3) Disconnect CNPF1 on the...
Page 75
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) POWER UNIT2 BALLAST Partition Disassembling 1) Disconnect CNLP2 and CNBL2 from the POWER UNIT2 BALLAST. 2) Remove a screw to detach the POWER UNIT2 POWER UNIT2 BALLAST from the ballast holder. BALLAST 3) Detach the insulating covers from POWER UNIT2 BALLAST.
Page 76
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) POWER UNIT1 BALLAST Ballast Disassembling holder 1) Turn over the ballast holder, disconnect CNLP1 and CNBL1 from POWER UNIT1 BALLAST and put the cables away from the holes. 2) Remove 2 Vcrews to detach POWER UNIT1 BALLAST Insulating and the insulating sheet from the holder.
Page 77
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) SENSOR-A/B PCB Ballast cover Disassembling 1) Disconnect CNOSS and CNISS from SENSOR-A PCB and SENSOR-B PCB. 2) Turn the cover over, and remove the sensor cover. SENSOR-B PCB 3) Remove SENSOR-A PCB and SENSOR-B PCB from the cover.
Page 78
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) REAR POWER UNIT (POWER UNIT1/2 CIRCUIT, POWER EXHAUST FAN) NOTE: Remove the MAIN PCB block before disassembling the POWER UNIT HOLDER. Disassembling 1) Remove a silver screws to detach CNGDS. 2) Remove 4 silver and 2 black screws to detach the circuit holder.
Page 79
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 4) Wire the cables and attach the partition as below. CNAC1 CNPF1 CNTS CNPW1 POWER UNIT1 CIRCUIT Wire CNPF1 beneath POWER UNIT1 CIRCUIT. Wire CNAWV beneath POWER UNIT1 CIRCUIT. Partition Clip the partition...
Page 80
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) POWER UNIT2 CIRCUIT T3x12 Insulating Disassembling black screws 1) Remove 2 screws to detach the insulating lid. 2) Remove 3 screws, put the cables away from the holes Torque: 0.68- and detach POWER UNIT2 CIRCUIT from the circuit 0.88Nm...
Page 81
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) )5217 32:(5 81,7 (AC WATCH PCB, POWER UNIT COOLING, POWER INTAKE FAN, BATTERY PCB) 127( Remove the MAIN PCB block before disassembling the REAR POWER UNIT. Disassembling 1) Remove 2 silver and 3 black screws, detach the AC holder and disconnect CNAWV from the AC WATCH PCB.
Page 82
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Assembling Wire CNAC1/2 Wire CNAC1/2 as 1) Attach the BATTERY PCB and the battery through these this location clamps holder in place on the bottom case and screw down. 2) Attach the POWER INTAKE FAN in place.
Page 83
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) Wiring Wire the cables as below. Attention Loop CNACR as below. Wire CNACR by passing it through this groove. CNACR Outside View Side View AC holder CNACR & CNAC CNAWD Wire CNAC through this hook.
Page 84
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) AC WATCH PCB T3x12 black screws Disassembling 1) Disconnect all the cables on the AC WATCH PCB. AC WATCH 2) Remove 2 screws to detach the AC WATCH PCB. 3) Separate the AC shield and the AC holder.
Page 85
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) LAMP1/2 DOWN FAN, IRIS FAN Disassembling 1) Remove 3 screws to detach the lamp duct. 2) Remove 2 screws each to detach the LAMP1/2 DOWN FAN and IRIS FAN. 3) Remove a screw to detach the metal mesh and the insulating sheet.
Page 86
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) IRIS FAN 40mm IRIS FAN Pass IRIS FAN cable through this groove. BOTTOM CASE Insulating sheets Disassembling Remove 19 screws and detach the insulating sheets and the bottom metal. Bottom metal NOTE Remember to detach the insulating sheets and the bottom metal and re-use them with new BOTTOM CASE.
Page 87
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) 5HSODFHPHQW 3DUWV OLVW PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 88
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 89
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 90
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 91
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 92
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 93
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 94
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.
Page 95
DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P) PRODUCT SAFETY NOTE: &RPSRQHQWV PDUNHG ZLWK D have special characteristics important to safety. Don’t degrade the safety of the projector through improper servicing. 7KH ¿JXUHV LQ WKH ³6<0%2/ 1R´ FROXPQ FRUUHVSRQG WR WKRVH LQ WKH GUDZLQJV RI WKH FKDSWHU 'LVDVVHPEO\ GLDJUDP.