Christie DWU951 Service Manual page 11

DWU951 (DD1-WU80P/81P) / DWX951 (DD1-WX80P/81P) / DXG1051 (DD1-X100P/101P)
4-5 Setup of the projector
Following contents are also described in User's manual.
z Adjusting the zoom and focus
1. The ZOOM or FOCUS dialog will appear when you press any of the
buttons from ZOOM, ZOOM -,
ZOOM +, FOCUS + and FOCUS -.
2. Use the ZOOM + / - buttons to adjust the screen size.
3. Use the FOCUS + / - buttons to focus the picture.
NOTE:
The projector may ignore operation by other buttons while the lens is moving.
z Adjusting the lens position
Press the LENS SHIFT button. The LENS SHIFT dialog will appear. Using the
   EXWWRQV ZKLOH WKH GLDORJ LV GLVSOD\HG VKLIWV WKH OHQV *HQHUDOO\
better image quality can be got when the lens is set to the center. Press the
LENS SHIFT button again to exit the LENS SHIFT function.
z CENTERING
Press the ENTER or INPUT button while the dialog is displayed to
execute the CENTERING feature, which adjusts the lens to the center. A message
GLDORJ LV GLVSOD\HG IRU FRQ¿UPDWLRQ 3UHVVLQJ WKH
You can also perform CENTERING in the standby mode by pressing the FUNCTION
and LENS SHIFT buttons on the control panel for 3 seconds at the same time.
NOTE:
‡ While the lens is moving to the center, the menu will disappear and an hourglass icon will
DSSHDU RQ WKH VFUHHQ &(17(5,1* PD\ WDNH VRPH WLPH WLOO WKH OHQV UHDFKHV WKH FHQWHU
‡ 7KH SURMHFWRU PD\ LJQRUH RSHUDWLRQ E\ EXWWRQV ZKLOH PRYLQJ WKH OHQV
‡ 7KH &(17(5,1* IHDWXUH ZKLOH WKH SURMHFWRU LV LQ WKH VWDQGE\ PRGH LV GLVDEOHG LI WKH 67$1'%< 02'(
item of SETUP menu is set to POWER SAVE. Perform CENTERING before the projector's power is turned
off, or set the STANDBY MODE to NORMAL.
‡ 7KH DGMXVWDEOH UDQJH RI /(16 6+,)7 YDULHV GHSHQGLQJ RQ WKH OHQV XQLW PRXQWHG RQ WKH SURMHFWRU WR
maintain picture quality. Therefore LENS SHIFT adjustment may not reach the end of the indicator in the
dialog, and that is not a failure.
z LENS MEMORY This projector is equipped with memory functions for
the lens adjustments (ZOOM, FOCUS, LENS SHIFT and LENS TYPE).
Up to 3 sets of adjustments can be stored.
To utilize the lens memory feature, press the LOAD or FUNCTION but-
ton while the LENS SHIFT dialog is displayed, or press
the ZOOM or FOCUS dialog is displayed. Then the LENS MEMORY
dialog will appear. The current lens adjustments are displayed on the
"CURRENT" line. The adjustments already stored in the lens memory
are displayed on the lines of SAVE and LOAD-1 to 3.
< SAVE>
To utilize the save lens memory feature, press the
CURRENT is selected on LENS MEMORY dialog or press the SAVE button
on the remote control. To store the current lens adjustments, select one of
the "SAVE" options numbered 1 to 3 (number of the lens memory) and press
WKH RU ENTER button, while LENS MEMORY OSD is displayed.
Remember that the current data being stored of a memory will be lost by
saving new data into the memory.
< LOAD>
To recall stored adjustments, select one of the "LOAD" options numbered 1 to 3 (number of the lens
PHPRU\ DQG SUHVV WKH
5HPHPEHU WKDW WKH FXUUHQW DGMXVWHG FRQGLWLRQ ZLOO EH ORVW E\ ORDGLQJ GDWD ,I \RX ZDQW WR NHHS WKH FXUUHQW
adjustment, please save it before performing a LOAD function.
< CLEAR LENS MEMORY>
7R FOHDU WKH DGMXVWPHQW VWRUHG LQ D OHQV PHPRU\ VHOHFW &/($5 /(16 0(025< DQG SUHVV WKH
ENTER EXWWRQ ZKLOH /(16 0(025< 26' LV GLVSOD\HG 3UHVV WKH
IRU FRQ¿UPDWLRQ 3UHVV WKH
NOTE:
The projector may ignore operation by buttons while moving the lens.
DWU951/DWX951/DXG1051 Service Manual
020-000674-01 Rev.1 (01-2014)
button performs CENTERING.
RU ENTER button, while LENS MEMORY OSD is displayed.
EXWWRQ DJDLQ WR FOHDU DOO RI WKH OHQV PHPRU\
FOCUS + / -
buttons
LENS SHIFT
button
button while
button while
EXWWRQ $ PHVVDJH GLDORJ LV GLVSOD\HG
9
ZOOM + / -
buttons
LENS SHIFT
button
ZOOM button
FOCUS - / + FUNCTION
buttons button
FUNCTION button
LENS
MEMORY
button
RU
Page 9 / 118