Cisco ONS 15454 Series Procedure Manual page 90

Before You Begin
7. NTP-G7 Install the Power and Ground, page
the
NTP-G8 Install the Fan-Tray Assembly, page
8.
assembly in the shelf.
NTP-G9 Install the Alarm Expansion Panel (ANSI Only), page
9.
you are planning to install the AIC-I card and want to increase the number of alarm contacts
provided by the AIC-I card.
NTP-G10 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections, page
10.
as needed to set up wire-wrap pin connections.
NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only), page
11.
procedure to connect an external wire-wrap panel to the alarm expansion panel (AEP).
NTP-G12 Install and Close the FMEC Cover (ETSI Only), page
12.
install the FMEC cover.
13. NTP-G13 Install the Rear Cover (ANSI Only), page
install the rear cover after you have finished servicing the backplane.
NTP-G14 Install DWDM Equipment, page
14.
equipment needed for dense wavelength division multiplexing (DWDM) networks.
NTP-G15 Install the Common Control Cards, page
15.
TCC2/TCC2P/TCC3 card, the AIC-I card, and the MS-ISC-100T card.
16. NTP-G144 Provision a Multishelf Node, page
17. NTP-G301 Connect the ONS 15454 Multishelf Node and Subtending Shelves to an MS-ISC-100T
Card, page
18. NTP-G302 Connect the ONS 15454 Multishelf Node and Subtending Shelves to a Catalyst 2950,
page
19. NTP-G303 Configure a Cisco Catalyst 2950 for a ONS 15454 Multishelf Node,
page
NTP-G304 Configure the MS-ISC-100T Card for a ONS 15454 Multishelf Node for Non-Default
20.
Public and Private VLAN IDs, page
NTP-G16 G307 Perform the ONS 15454 Shelf Installation Acceptance Test, page
21.
this procedure to determine if you have correctly completed all other procedures in the chapter.
22. NTP-G295 Connect the ONS 15454 Multishelf Node and Subtending Shelves to a Catalyst 3560,
page
NTP-G296 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration Using the Catalyst
23.
3560, page
NTP-G297 Upgrade the ONS 15454 Multishelf with Catalyst 2950 Configuration Using the
24.
Catalyst 3560, page
25. NTP-G298 Configure a Cisco Catalyst 3560 (Active and Standby) for a Multishelf Node,
page
26. NTP-G299 Configure a Cisco Catalyst 3560 (Extended) for a Multishelf Node,
page
27. NTP-G300 Configure a Cisco Catalyst 3560 for a Multishelf Node Upgrade, page
this procedure as needed.
Cisco ONS 15454 DWDM Procedure Guide, Release 9.2
1-2
"NTP-G8 Install the Fan-Tray Assembly" procedure on page
1-81—Complete this procedure as needed.
1-83—Complete this procedure as needed.
1-84—Complete this procedure as needed.
1-90—Complete this procedure as needed.
1-92—Complete this procedure as needed.
1-94—Complete this procedure as needed.
1-96—Complete this procedure as needed.
1-97—Complete this procedure as needed.
Chapter 1
1-33—Complete this procedure before continuing with
1-41—Complete this procedure to install the fan-tray
1-65—Complete this procedure as needed to
1-66—Complete this procedure as needed to install
1-74—Complete this procedure to install the
5-10—Complete this procedure as needed.
1-85—Complete this procedure as needed.
Install the Cisco ONS 15454 Shelf Assembly
1-41.
1-45—Complete this procedure if
1-48—Complete
1-59—Complete this
1-63—Complete this procedure to
1-87—Complete
1-98—Complete
78-19286-01