Table of Contents
Advertisement
Front Panel Connector
Parallel
2
26
2
10
Front Audio
1
9
Buzzer
S/PDIF
1
25
1
5
2
12
Front
DIO
DIO Power
Panel
USB 2.0
9
1
5
1
System
LAN 2
Fan 1
Clear CMOS
Data (JP1)
LAN 1
1
1
ECX
SPI Flash
BIOS
USB 1-2
USB 3.0
LPC
14
USB 3-4
USB 3.0
2
1
HDMI (default)/DP
SATA 3.0
SATA 0
SATA 1
1
1
DVI
1
4
1
4
1
System
Fan 2
6
4-pin DC-out
JP2
2
6
J21
PCIe x16 (PCIE1)
DC-in
2
HDD-LED - HDD LED
This LED will be lit when the hard drive is being accessed.
RESET SW - Reset Switch
This switch allows you to reboot without having to power off the system.
ATX-SW - ATX Power Switch
This switch is used to power on or off the system.
PWR-LED - Power/Standby LED
When the system's power is on, this LED will be lit. When the system is in the S1 (POS - Pow-
er On Suspend) state, it will blink every second. When the system is in the S3 (STR - Suspend
To RAM) state, it will blink every 4 seconds.
Pin Pin Assignment
3
HDD Power
HDD-LED
5
Signal
PWR-LED
7
Ground
9
RST Signal
RESET SW
11
N.C.
User's Manual | KS-SD
Front
Panel
Auto Power-on
Select (JP11)
1
Power Button
PWR-LED
DDR4_1 SODIMM
Power LED
HDD LED
6
6
DDR4_2 SODIMM
2
1
1
Reset
(JP4)
(JP10)
1
STB_LED
2
10
HDD-LED
COM 4
1
9
RESET-SW
(JP9) (JP16)
6
6
1
1
(JP8) (JP15)
6
6
1
1
2
10
COM 3
1
9
2
10
COM 2
1
9
(JP7) (JP14)
6
6
COM 2
2
2
1
1
(JP6)
(JP13)
6
6
1
1
(JP12)
(JP5)
6
6
1
1
2
10
COM 1
COM 1
1
9
16
6
JP3
VGA
1
1
1
2
J22
1
2
1
PCIe x4 (PCIE2)
Pin Pin Assignment
2
LED Power
4
LED Power
6
Signal
8
Ground
ATX-SW
10
Signal
SATA (Serial ATA) Connectors
2
ATX-SW
Front Audio
1
Buzzer
S/PDIF
1
DIO
1
USB 2.0
9
LAN 2
LAN 1
ECX
USB 1-2
USB 3.0
LPC
14
USB 3-4
USB 3.0
2
HDMI (default)/DP
DVI
DC-in
Features
•
2 Serial ATA 3.0 ports
- SATA port 0 and 1 with data transfer rate up to 6Gb/s
The Serial ATA connectors are used to connect the Serial ATA device. Connect one end of the
Serial ATA data cable to the SATA connector on the system board and the other end to your
Serial ATA device.
The power cable must be connected from the system board's Serial ATA power connector to a
SATA drive's power connector in order to provide power to the drive. Refer to the next page
for pin definitions of the SATA power connectors.
BIOS Setting
Configure the Serial ATA drives in the Advanced submenu ("SATA Configuration" section) of the
BIOS. Refer to Chapter 7 for more information.
Parallel
10
2
26
9
1
25
5
Auto Power-on
2
12
Front
Select (JP11)
DIO Power
Panel
5
Power Button
DDR4_1 SODIMM
Power LED
HDD LED
6
DDR4_2 SODIMM
1
1
1
System
(JP4)
(JP10)
Fan 1
STB_LED
Clear CMOS
Data (JP1)
1
2
COM 4
1
1
(JP9) (JP16)
SPI Flash
6
BIOS
1
(JP8) (JP15)
6
1
2
COM 3
1
2
COM 2
1
1
(JP7) (JP14)
6
SATA 3.0
2
1
SATA 0
SATA 1
(JP6)
1
1
6
1
(JP5)
6
1
1
4
4
1
2
1
System
COM 1
Fan 2
1
16
6
6
4-pin DC-out
JP2
JP3
VGA
1
1
2
1
2
J22
6
1
2
J21
PCIe x16 (PCIE1)
2
1
PCIe x4 (PCIE2)
Chapter 5
1
6
Reset
10
9
6
1
6
1
10
9
10
SATA 0/1
9
6
COM 2
2
1
(JP13)
6
1
(JP12)
6
1
1
7
10
COM 1
9
SATA 3.0 6Gb/s
25
Advertisement
Table of Contents
