Table of Contents
Advertisement
Chapter 4 - Jumper Settings
Clear CMOS Data
Front Audio
Buzzer
3
USB 2.0
2
1
1-2 On: Normal
LAN 2
(default)
JP1
LAN 1
ECX
3
USB 1-2
USB 3.0
2
1
USB 3-4
USB 3.0
2-3 On: Clear CMOS Data
HDMI (default)/DP
DVI
DC-in
If you encounter the following conditions, you can reconfigure the system with the default val-
ues stored in the BIOS ROM.
a) CMOS data becomes corrupted.
b) You forgot the supervisor or user password.
To load the default values stored in the ROM BIOS, please follow these steps below:
1. Power-off the system and unplug the power cord.
2. Set the jumper pins 2 and 3 to On. Wait for a few seconds and set the jumper back to its
default setting: 1-2 On.
3. Now plug the power cord and power on the system.
User's Manual |KS-SD
2
Parallel
26
2
10
1
9
1
S/PDIF
25
Auto Power-on
1
5
2
12
Front
Select (JP11)
DIO
DIO Power
Panel
9
1
5
Power Button
DDR4_1 SODIMM
Power LED
HDD LED
6
DDR4_2 SODIMM
1
1
System
(JP4)
Fan 1
Clear CMOS
Data (JP1)
1
COM 4
1
SPI Flash
6
BIOS
(JP8) (JP15)
6
LPC
14
COM 3
COM 2
2
1
(JP7) (JP14)
6
SATA 3.0
2
SATA 1
SATA 0
(JP6)
1
1
6
(JP5)
6
1
1
4
4
1
COM 1
System
Fan 2
16
6
6
4-pin DC-out
JP2
JP3
VGA
1
2
1
2
1
J22
6
2
J21
PCIe x16 (PCIE1)
2
1
PCIe x4 (PCIE2)
Auto Power-on Select
Front Audio
Buzzer
S/PDIF
1
DIO
USB 2.0
9
6
1
Reset
(JP10)
LAN 2
STB_LED
2
10
LAN 1
1
9
(JP9) (JP16)
6
ECX
1
1
USB 1-2
USB 3.0
6
1
1
2
10
14
USB 3-4
USB 3.0
1
9
2
10
1
2
9
6
HDMI (default)/DP
COM 2
2
1
1
(JP13)
6
1
1
(JP12)
6
DVI
1
1
2
10
COM 1
1
9
1
DC-in
JP11 is used to select the method of powering on the system. If you want the system to
power-on whenever AC power comes in, set jumper pins 2 and 3 to On. If you want to use
the power button, set pins 1 and 2 to On.
When using the "Power On" feature to power the system back on after a power failure , the
system may not power on if the power lost is resumed within 5 seconds (power flicker).
Parallel
2
10
2
26
1
9
1
25
1
5
Auto Power-on
2
12
Front
Select (JP11)
DIO Power
Panel
1
5
Power Button
DDR4_1 SODIMM
Power LED
HDD LED
6
6
DDR4_2 SODIMM
1
1
1
System
Reset
(JP4)
(JP10)
Fan 1
STB_LED
Clear CMOS
Data (JP1)
1
2
COM 4
1
1
(JP9) (JP16)
SPI Flash
6
6
BIOS
1
(JP8) (JP15)
6
6
1
LPC
2
COM 3
1
2
COM 2
1
1
(JP7) (JP14)
6
6
SATA 3.0
2
2
1
SATA 1
SATA 0
(JP6)
(JP13)
1
1
6
6
1
(JP5)
(JP12)
6
6
1
4
1
4
1
2
1
System
COM 1
Fan 2
1
16
6
6
4-pin DC-out
JP3
JP2
VGA
1
2
1
2
1
J22
6
1
2
J21
PCIe x16 (PCIE1)
2
1
PCIe x4 (PCIE2)
Chapter 4
JP11
1
1 2
3
1-2 On:
Power-on via power button
(default)
10
1 2
3
9
2-3 On:
Power-on via AC power
1
1
10
9
10
9
COM 2
1
1
1
10
COM 1
9
16
Advertisement
Table of Contents
