ABB RELION REG670 Commissioning Manual page 10

Table of contents
12.4.1 Distance protection zones, quadrilateral characteristic ZMQPDIS.................................102
12.4.1.1 Measuring the operating limit of set values.....................................................................105
12.4.1.2 Measuring the operating time of distance protection zones....................................... 105
12.4.1.3 Completing the test.............................................................................................................. 106
12.4.2 Phase selection with load encroachment, quadrilateral characteristic FDPSPDIS .....106
12.4.2.1 Measuring the operating limit of set values.....................................................................108
12.4.2.2 Completing the test.............................................................................................................. 109
12.4.3 Full scheme distance protection, mho characteristic ZMHPDIS..................................... 109
12.4.3.1 Phase-to-phase faults............................................................................................................110
12.4.3.2 Phase-to-earth faults.............................................................................................................110
12.4.4 Faulty phase identification with load encroachment FMPSPDIS .....................................111
12.4.5 Distance protection zones, quadrilateral characteristic, separate settings
ZMRPDIS....................................................................................................................................... 111
12.4.5.1 Measuring the operating limit of set values..................................................................... 114
12.4.5.2 Measuring the operating time of distance protection zones........................................115
12.4.6 Phase selection, quadrilateral characteristic with settable angle FRPSPDIS................ 115
12.4.6.1 Measuring the operating limit of set values......................................................................117
12.4.6.2 Completing the test............................................................................................................... 118
12.4.7 High speed distance protection zones, quadrilateral and mho characteristic
ZMFPDIS.......................................................................................................................................118
12.4.7.1 Measuring the operating limit of set values......................................................................121
12.4.7.2 Measuring the operating time of distance protection zones........................................121
12.4.7.3 Completing the test............................................................................................................... 122
12.4.8 High Speed distance for series compensated line zones, quadrilateral and mho
characteristic ZMFCPDIS .........................................................................................................122
12.4.8.1 Measuring the operating limit of set values..................................................................... 125
12.4.8.2 Measuring the operating time of distance protection zones....................................... 125
12.4.8.3 Completing the test...............................................................................................................126
12.4.9 Power swing detection ZMRPSB ............................................................................................126
12.4.9.1 Verifying the settings............................................................................................................ 127
12.4.9.2 Testing the power swing detection function ZMRPSB ..................................................128
12.4.9.3 Testing the
12.4.9.4 Testing the block input, interaction between FDPSPDIS or FRPSPDIS
and ZMRPSB ............................................................................................................................128
12.4.9.5 Completing the test...............................................................................................................129
12.4.10 Pole slip protection PSPPPAM.................................................................................................129
12.4.10.1 Verifying the settings............................................................................................................ 129
12.4.10.2 Completing the test............................................................................................................... 131
12.4.11 Out-of-step protection OOSPPAM......................................................................................... 131
12.4.11.1 Verifying the settings............................................................................................................ 132
12.4.11.2 Test of point RE (R
12.4.11.3 Test of the boundary between zone 1 and zone 2, which is defined by the
parameter
12.4.11.4 Test of the point SE (R
12.4.12 Automatic switch onto fault logic ZCVPSOF....................................................................... 146
12.4.12.1 Activating ZCVPSOF externally............................................................................................147
12.4.12.2 Initiating ZCVPSOF automatically and setting mode to impedance...........................147
4
tR1 timer............................................................................................................. 128
, X )............................................................................................ 135
FwdR FwdX
ReachZ1 ................................................................................................................ 139
, X )........................................................................................142
RvsR RvsX
Commissioning manual