Maintenance; Maintenance.procedure; Reader; Electronic.key/Proximity.reader.deleting - urmet domus 1061/004 Installation And Programming Manual

7. MAINTENANCE

7.1 MAINTENANCE PROCEDURE
The.system.maintenance.procedure.allows.to.operate.on.the.system.components.–.as.control.panel,.keypads,.detectors,.sirens.–.without.siren.
alarm.signalling.or.telephone.calls.sending..After.entering.in.maintenance.mode,.the.tamper.line.is.disabled.and.so.it.is.possible.to.open.without.
problems.the.system.devices..The.maintenance.procedure.can.be.activated.with.a.Master.key.or.a.Master.code.
To.enter.in.the.maintenance.mode,.follow.the.instructions.below:
1.. Totally.disarm.the.system.with.a.Master.key.or.code..
2. Open the control panel within 2 minutes from disarming (the control panel tamper must be open).
The maintenance mode is signalled by a fast sequential blinking of LEDs on the control panel motherboard and on readers and keypads.
To.exit.from.the.maintenance.mode,.it.is.necessary.to.close.again.all.the.system.components.tampers.and.close.the.control.panel.(so.also.the.
control panel tamper is closed).

7.2 READER

7.2.1 ELECTRONIC KEY/PROXIMITY READER ADDITION
To.add.a.new.reader,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel..
4.. Disconnect.the.control.panel.backup.battery..
5. Add the new device (bus extension, connections, address selection), by following instructions in chapters 2, 3 and 4.
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel..
7.. Program.the.new.reader..
8.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.
7.2.2 ELECTRONIC KEY/PROXIMITY READER DELETING
To.delete.a.reader.from.the.system,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel..
4.. Disconnect.the.control.panel.backup.battery..
5.. Remove.the.device.and.verify.the.bus.continuity,.by.connecting.the.isolated.segments,.if.present..
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel.
7.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.
7.2.3 ELECTRONIC KEY/PROXIMITY READER REPLACEMENT
To.replace.a.reader,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel.
4.. Disconnect.the.control.panel.backup.battery.
5.. Remove.the.old.device.and.replace.it.with.the.new.one,.taking.care.to.set.the.same.address..
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel..
7.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.

7.3 KEYPAD

7.3.1 KEYPAD ADDITION
To.add.a.new.keypad,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel..
4.. Disconnect.the.control.panel.backup.battery..
5. Add the new device (bus extension, connections, address selection), by following instructions in chapters 2, 3 and 4.
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel..
7.. Program.the.new.keypad.
8.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.
7.3.2 KEYPAD DELETING
To.delete.a.keypad,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel..
4.. Disconnect.the.control.panel.backup.battery..
5.. Remove.the.device.and.verify.the.bus.continuity,.by.connecting.the.isolated.segments,.if.present..
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel.
7.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.
7.3.3 KEYPAD REPLACEMENT
To.replace.a.keypad,.follow.the.instructions.below:.
1.. Activate.the.system.maintenance.mode.(see.paragraph.7.1 Maintenance procedure).
.. Open.the.control.panel.
3.. Unpower.the.control.panel.
4.. Disconnect.the.control.panel.backup.battery..
5.. Remove.the.old.device.and.replace.it.with.the.new.one,.taking.care.to.set.the.same.address..
6.. Connect.again.the.backup.battery.and.power.again.the.control.panel..
7.. Close.the.control.panel.to.exit.from.the.maintenance.procedure.
36
DS1061-015B