Mrc Control, Convection, Gas; Mrc Control, Convection, Warming Drawer, Gas - Whirlpool AER5522VAS0 Manual

MRC Control, Convection, Gas

MRC Control, Convection, Warming Drawer, Gas

1. Press "BAKE" for 5 seconds.
2. Press TEMP/TIME "+" or "-".
1. Press "BAKE" for 5 seconds.
2. Press TEMP/TIME "+" or "-".
3. Press START.
3. Press START.
Action
1. Press CANCEL/CANCEL/START
2. Press the TEMP/TIME "+" key
Action
Press "+" again
1. Press CANCEL/CANCEL/START
"+" again
2. Press the TEMP/TIME "+" key
"+" again
Press "+" again
"+" again
"+" again
"+" again
"+" again
"+" again
"+" again
"+" again
"+" again
"+" again
When in the Diagnostic mode, instructions will be provided by the control to help you
"+" again
through each of the programs. Press Cancel to exit the test at any time.
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy
When in the Diagnostic mode, instructions will be provided by the control to help you
to use and when the test is complete, test results will be provided. Whenever servicing the
through each of the programs. Press Cancel to exit the test at any time.
oven, this is the test to run.
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy
to use and when the test is complete, test results will be provided. Whenever servicing the
oven, this is the test to run.
When checking for fault codes and "NO FAULTS" is displayed, do not change the control.
When checking for fault codes and "NO FAULTS" is displayed, do not change the control.
MRC Convection, Gas
Temperature Adjustment
Previous Offset shown, or U-00 is displayed.
Temperature Adjustment
Adjusts temperature in 5⁰F (3⁰C) increments
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Previous Offset shown, or U-00 is displayed.
Bake and Broil Temperatures are offset
Adjusts temperature in 5⁰F (3⁰C) increments
automatically to the same degree.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
If START is not pressed within 1 minute,
Bake and Broil Temperatures are offset
adjustment is ignored.
automatically to the same degree.
If START is not pressed within 1 minute,
adjustment is ignored.
Diagnostic Mode
Diagnostic Mode
"TEST ON" ##⁰F "UO"
"USAGE"
"ENG MODE"
"TEST ON" ##⁰F "UO"
"TEST MODE"
"USAGE"
"VERSION"
"ENG MODE"
"DISPLAY"
"TEST MODE"
"CONTROL RESET"
"VERSION"
"FAULTS"
"DISPLAY"
"AUTO TEST"
"CONTROL RESET"
the OVEN, automatically)
"FAULTS"
"AUTO TEST"
the OVEN, automatically)
*Press "START TIME" to clear all fault codes
*Press Start Time to clear all fault codes
*Press Start Time to clear all fault codes
2- 6
Models:
GFG461LVB0
GFG461LVB1
GFG461LVB2
GFG461LVQ0
GFG461LVQ1
GFG461LVQ2
GFG461LVS0
GFG461LVS1
GFG461LVS2
Models:
GFG471LVB0
GFG471LVB1
GFG471LVQ0
GFG471LVQ1
GFG471LVS0
GFG471LVS1
Display
(In the test mode)
(Displays hours of Operation)
Display
(Manufacturing Information)
(In the test mode)
(Manual check of Control relays)
(Displays hours of Operation)
(Manufacturing Information)
(Manufacturing Information)
(Checks all LEDs in Display)
(Manual check of Control relays)
(Resets Control settings)
(Manufacturing Information)
*(Displays all Fault Codes)
(Checks all LEDs in Display)
(Performs a complete check of
(Resets Control settings)
*(Displays all Fault Codes)
(Performs a complete check of
GFG461LVT0
GFG461LVT1
GFG461LVT2
GFG464LVB0
GFG464LVB1
GFG464LVQ0
GFG464LVQ1
GFG464LVS0
GFG464LVS1