Summary of Contents for Avaya Scopia Elite 6000 MCU Series
Page 1
Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Release 9.0 Issue 1 January 2017...
Page 2
RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU the express behalf of Avaya. End User agrees to indemnify and hold AND ANYONE ELSE USING OR SELLING THE SOFTWARE harmless Avaya, Avaya's agents, servants and employees against all WITHOUT A LICENSE.
Page 3
OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL written consent of Avaya can be a criminal, as well as a civil offense INFORMATION FOR H.264 (AVC) AND H.265 (HEVC) CODECS under the applicable law.
Page 4
All non-Avaya trademarks are the property of their respective owners. ® Linux is the registered trademark of Linus Torvalds in the U.S. and other countries.
........................ 32 Documentation ............. 36 Finding documents on the Avaya Support website .......................... 36 Training .......................... 37 Support ................ 37 Using the Avaya InSite Knowledge Base January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Elite 6000 MCU hardware installation checklist and procedures. ® This document is intended for people who install the Scopia Elite 6000 MCU hardware at a customer site. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Checking Site Suitability Prior to setting up your device, you need to verify your site suitability for: • System power requirements • System environmental requirements January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
7. Take the device out of the shipping box. 8. Carefully open the additional boxes, remove the packing material, and remove the drives and other contents. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
PSUs can be hot-swapped, enabling you to replace the power unit without powering down the device. You can add the PSU when the MCU is functioning. However, Avaya strongly recommends to turn off the MCU when you perform the procedure for the first time.
Page 12
Rack mounting preparation Before you begin Verify you have the following equipment: • The standalone PSU that you can order from your local Avaya representative using these references: - Scopia Elite MCU Redundant Power Supply - Part number 55547-00018 • An antistatic wrist strap Procedure 1.
Page 13
Adding a Power Supply Unit to the MCU Figure 3: Adding a PSU in Scopia Elite MCU 4. Reconnect the two power cords. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
The device takes up 3 holes (1U) on the posts. You need at least 2 additional holes to slide the device into the rack. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
• Ensure that the environment is suitable for the rack, considering factors such as the ambient temperature of the room. Read the safety instructions that came with your rack for details. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 16
- If there are few devices mounted in the rack, find the lowest possible location to mount the device, to ensure the rack remains stable. Related links Setting up the Device on page 14 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
The rails (and 8 of the cage nuts and screws required to attach the rails) are not used for shelf mounting. Figure 6: Accessories required for mounting Related links Mounting the Device on to the Rack on page 17 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
2. Count 4 square holes up. At the 4th hole mark the location of the upper MCU-fixing cage nut. 3. Repeat this procedure for the other front-facing post. Related links Mounting the Device on to the Rack on page 17 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
4. Insert the second cage nut in the same way, in the square hole directly above it. 5. Repeat this procedure for each post. Related links Mounting the Device on to the Rack on page 17 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
- Two long outer rails - Two short outer rails - Two flat-head long screws (Phillips cross recessed flat-head machine screws M5x12mm) - Two brackets (finishing washers M5) January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 21
(Figure 13: Connecting the two outer rails on page 21). Figure 13: Connecting the two outer rails January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 22
Attach it to the front of the rack as you did to the rear of the rack. Important: To unfasten the rail pins from the rack, push the safety latch to release: Figure 15: Removing the rack from the rails January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 23
The outer rail is now attached to the rack, as shown in Figure 17: Side view of rack with the outer rail attached on page 24. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
(Figure 18: Preparing the parts required to mount the device onto the rails on page 25): - Two inner rail extensions January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 25
Secure the rear inner rail extension through one of the two holes on the rail extension, using one flat-headed short screw (Figure 20: Securing rail extensions to the device page 26). January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 26
As you slide, you should hear two clicks; one mid-way and one near the end. These are the safety latches to stop the device from accidentally sliding out. Figure 21: Sliding the device onto the rails January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 27
This secures the front panel to the front of the rack and the outer rail to the rack. The outer rail was already secured in Mounting the Outer Rails on to the Rack on page 20. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
MCU location or on the site environment. Related links Setting up the Device on page 14 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
1. On the rear panel, connect the power cable to the AC power connector (Figure 24: Rear panel of the device on page 29). Figure 24: Rear panel of the device January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
2. Verify that the status LED is lit green (selected models only). 3. Check the network connection by verifying that the Ethernet activity LED is lit green. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 31
Figure 27: The Equinox Management Dashboard status f. Exit the videoconference by disconnecting the call. Related links Setting up the Device on page 14 January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Plan for and deploy Avaya Scopia XT Partners, Services, XT Desktop Server for IP Office Desktop Server for IP Office and Support personnel Table continues… January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 33
Power Suite Administrator Guide for Avaya Perform administration tasks for Avaya System Equinox Streaming and Recording Equinox Streaming and Recording Server administrators Server Table continues… January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 34
Reference Guide for Avaya Equinox Understand how to configure Avaya Equinox System Management SNMP Traps Management to send information to a administrators, Customers, Partners, Table continues… January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Page 35
Video Gateway for Microsoft Lync ® User Guide for Avaya Scopia Understand the features of and use Avaya Customers ® Desktop Client Scopia XT Desktop Client Table continues… January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Use this procedure to find product documentation on the Avaya Support website. Procedure 1. Use a browser to navigate to the Avaya Support website at http://support.avaya.com/. 2. At the top of the screen, enter your username and password and click Login.
• Links to other pertinent information If you are an authorized Avaya Partner or a current Avaya customer with a support contract, you can access the Knowledge Base at no extra cost. You must have a login account and a valid Sold-To number.
5. Select the product from the drop down list and choose the relevant release. 6. Select the Technical Solutions tab to see articles. 7. Select relevant articles. January 2017 Rack Mounting Guide for Avaya Scopia Elite 6000 MCU Comments on this document? infodev@avaya.com...
Need help?
Do you have a question about the Scopia Elite 6000 MCU Series and is the answer not in the manual?
Questions and answers