1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY RX800 S2
  6. Operating manual

Fujitsu PRIMERGY RX800 S2 Operating Manual

Hide thumbs Also See for PRIMERGY RX800 S2:
Table of Contents

Advertisement

Quick Links

Download this manual
Produktfamilie
PRIMERGY RX800 S2
Operating Manual
Gottfried Staubach
Fujitsu Siemens Computers GmbH Paderborn
33094 Paderborn
e-mail: email: manuals@fujitsu-siemens.com
Tel.: 05251 14888-19
Fax: (++49) 700 / 372 00001
U41621-J-Z156-1-76
Sprachen: En
Edition November 2005

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY RX800 S2

Summary of Contents for Fujitsu PRIMERGY RX800 S2

  • Page 1 Produktfamilie PRIMERGY RX800 S2 Operating Manual Gottfried Staubach Fujitsu Siemens Computers GmbH Paderborn 33094 Paderborn e-mail: email: manuals@fujitsu-siemens.com Tel.: 05251 14888-19 Fax: (++49) 700 / 372 00001 U41621-J-Z156-1-76 Sprachen: En Edition November 2005...
  • Page 2 Gesellschaft für Technik-Dokumentation mbH www.cognitas.de Copyright and Trademarks Copyright © 2005 Fujitsu Siemens Computers GmbH. All rights reserved. Delivery subject to availability; right of technical modifications reserved. All hardware and software names used are trademarks of their respective manufacturers.
  • Page 3 Introduction Important Notes Installing the Server Preparation for Operation Troubleshooting and Tips Hot-plug Components Abbreviations Related Publications Index...

  • Page 5: Table Of Contents

    Contents Introduction ......1 Overview of the Documentation ....2 Features .
  • Page 6 Contents 4.3.11 Using the BMC utility programs ....84 Cleaning the Server ......87 Troubleshooting and Tips .

  • Page 7: Introduction

    Security functions in BIOS-Setup and on the I/O Board protect the data on the server against manipulation. The lockable door of the rack offers additional security. The PRIMERGY RX800 S2 is supplied as a rack-mounted model and occupies three height units in the rack. U41621-J-Z156-1-76...

  • Page 8: Overview Of The Documentation

    Concept and Target Group of this Manual This operating manual describes how to install, commission and operate your PRIMERGY RX800 S2 server system, and how to replace hot-plug modules. It is intended for those responsible for installing the hardware and ensuring that the system runs smoothly.
  • Page 9 ServerView Suite - ServerStart" is also available on the ServerBooks CD. If you need a backup of the ServerBooks CD, send the details of your server via email address: Reklamat-PC-LOG@fujitsu-siemens.com. – "RemoteView Management Board RSA-II User Manual" – "ServeRAID-8i HDD Controller User Manual"...

  • Page 10: Features

    Features Introduction Features Performance Impressive performance using the latest microprocessor technology. The basic ® configuration is a 4-way building block (node), thus supporting up to four Intel Xeon™ MP dual-core microprocessors. In the basic configuration, the system comes with two microprocessors. You can install up to four microprocessors to further enhance performance and symmetric multiprocessing (SMP) capability.
  • Page 11 Introduction Features error is then reported so that preventative maintenance can be performed. As long as there are enough good locations to allow the proper operation of the server, no further action is taken other than recording the error in the error logs. If the error is not recoverable, then Memory Scrubbing sends an error message to the LED Diagnostic Path, which then turns on the proper lights and LEDs to guide you to the damaged DIMM.
  • Page 12 Features Introduction LED Diagnostic Path The LED Diagnostic Path feature provides LEDs to assist in isolating problems with the server. A light on the Operator Information Panel is lit if an unusual condition or a problem occurs. If this happens, you can look at the LEDs inside the Operator Information Panel drawer and those visible through the cover of the server to isolate the cause.
  • Page 13 Introduction Features Accessible IDE Drive The system features one accessible 0,5-inch IDE drive. In the basic configu- ration, the server is equipped with a CD/DVD-ROM drive connected via a fast IDE controller. The drive can not be replaced during operation. Hot-plug PCI-X The server is equipped with six PCI-X 2.0 slots, all offering 64-bit support, operating at 266 MHz, and supporting hot-plug functionality.
  • Page 14 (see “Related Publications” on page 133). Service and Support The PRIMERGY RX800 S2 is service-friendly and modular (compute node housing), thus enabling quick and simple maintenance. Blue or green on a component indicates "touch points", where you can grip the component to remove it from or install it in the server, open or close a latch, and so on.
  • Page 15 Introduction Features Feature List The following is an abbreviated list of the features that the server supports: Active memory Advanced configuration and power interface (ACPI) Advanced Desktop Management Interface (DMI) features Advanced memory ECC, including Redundant Bit Steering Auto-restart initial program load (IPL) power supply Automatic BIOS recovery (ABR) Automatic error retry and recovery Automatic server restart (ASR&R)
  • Page 16 Features Introduction Memory Scrubbing Monitoring support for temperature, voltage, and fan speed Parity checking on the small computer system interface (SCSI) bus and PCI buses Power-managed and Advanced Configuration and Power Interface (ACPI) compliant Power-on self-test (POST) Predictive Failure Analysis (PFA) alerts Redundant Bit Steering Redundant Ethernet capabilities (requires optional Ethernet adapter) with failover support...
  • Page 17 Introduction Features Processors Up to 4 processors (depending on configuration): ® – Intel Xeon™ MP dual-core – MP 7020: 2x1 MB Level-2 cache, ECC, 2.67 GHz – MP 7040: 2x2 MB Level-2 cache, ECC, 3.0 GHz – 667 MHz Front Side Bus –...
  • Page 18 Features Introduction Integrated functions – Broadcom Dual Gigabit Ethernet controller 10/100/1000 MBit (two RJ45 ports) – 6-Port SAS controller – ServeRAID-8i RoMB controller featuring RAID levels 0, 1, 10, 5, 50. 256 MB RAID Cache and BBU included. – LED Diagnostic Path feature –...

  • Page 19: Notational Conventions

    Introduction Notational Conventions Notational Conventions Identifies commands, menu items, names of buttons, italic type options, variables, file names, path names and input within the body of the text. Used for messages and prompts on the screen. fixed-width type [Key symbols] Keys are shown as they appear on the keyboard.

  • Page 20: Technical Data

    Technical Data Introduction Technical Data Electrical Data Rated voltage range 100 V to 127 V AC 200 V to 240 V AC (auto sense) Frequency 50 Hz / 60 Hz Max. mains current 8,5 A / 8,5 A Apparent power (max.) 1600 VA Effective power (max.) 1300 W...
  • Page 21 Introduction Technical Data Environmental Conditions (according to EN 60721-3-3) Operating climate (Class 3K2): Temperature (°C) 10 to 35 Relative humidity(%) 8 to 80 Environmental conditions/transport (Class 2K2): Temperature (°C) -40 to 60 Relative humidity (%) 5 to 100 (* including condensation but excluding rain) Mechanical environmental conditions Operation...
  • Page 22 Technical Data Introduction Certification Global/Europe CB/CE (product safety) Germany USA/Canada C/US Certification Australia C-Tick Mark (electromagnetic Japan VCCI compatibility) Taiwan BSMI Mexico NOM-018 Russia Gost Table 6: Standards Noise level (ISO 9296) Sound power level (L max. 6.6 B Operating sound pressure level <= 60 dB (A) in standard configuration Table 7: Noise level Maintenance surfaces and ventilation clearances...

  • Page 23: Important Notes

    Important Notes In this chapter you will find essential information regarding safety when working with your server. Notes on Safety You will also find the following safety instructions in the manual entitled “Safety“. This device complies with the relevant safety regulations for data processing equipment.
  • Page 24 Notes on Safety Important Notes Before Setting up CAUTION! During installation and before operating the device, observe the instructions on environmental conditions for your device (see section “Technical Data” on page 14). If the device is brought in from a cold environment, condensation may form both inside and on the outside of the machine.
  • Page 25 Important Notes Notes on Safety CAUTION! Always connect the device and the attached peripherals to the same power circuit. Otherwise you run the risk of losing data if, for example, the central processing unit is still running, but the peripheral device (e.g.
  • Page 26 Notes on Safety Important Notes CAUTION! Install only system expansions that satisfy the requirements and rules governing safety and electromagnetic compatibility and relating to telecommunications terminal equipment. If you install other expan- sions, you may damage the system or violate the safety regulations and regulations governing RFI suppression.
  • Page 27 Important Notes Notes on Safety Notes on Handling CDs/DVDs and CD/DVD Drives CAUTION! Use only CDs/DVDs in proper condition in the CD/DVD drive of your server to prevent data loss, damage to the device and injuries. Therefore, check each CD/DVD for damage, cracks, breakage etc. before inserting it in the drive.
  • Page 28 Notes on Safety Important Notes Modules with Electrostatic-Sensitive Devices: Electrostatic-sensitive components may be identified by the following sticker: Figure 1: ESD label When you handle components fitted with ESDs, you must observe the following points under all circumstances: Remove the power plugs from the power sockets before inserting or removing components containing ESDs.

  • Page 29: Ce Certificate

    Important Notes CE Certificate Other Important Notes: When cleaning the device, please observe the relevant notes in the section “Cleaning the Server” on page 87. Keep this operating manual and all additional documentation together with the device. All documentation should be included if the device is passed on to a third party.

  • Page 30: Transporting The Server

    Consult the dealer or an experienced radio/T.V. technician for help. Fujitsu Siemens Computers is not responsible for any radio or television inter- ference caused by unauthorized modifications of this equipment or the substi- tution or attachment of connecting cables and equipment other than those specified by Fujitsu Siemens Computers.

  • Page 31: Notes On Installing Into The Rack

    Important Notes Notes on Installing into the Rack Notes on Installing into the Rack CAUTION! For safety reasons, at least two people are required to install the rack model because of its weight and size. Never lift the server into the rack using the handles on the front panel. When connecting and disconnecting cables, observe the relevant notes in the chapter ”Important notes“...

  • Page 32: Environmental Protection

    Important Notes Environmental Protection Environmentally Friendly Product Design and Development This product has been designed in accordance with the Fujitsu Siemens Computers standards for ”environmentally friendly product design and devel- opment“. This means that the designers have taken into account important...
  • Page 33 Important Notes Environmental Protection Returning Used Electrical and Electronic Devices in EU Countries – Separate collection Users of electrical and electronic devices are obligated to collect used devices separately. Electrical (electronic) used devices may not be disposed of together with unsorted household refuse. The separate collection is a condition for reuse, recycling and utilisation of used electrical (electronic) devices, which ensures the protection of resources.
  • Page 34 Local Contacts For details on take-back and reuse of devices and consumables within Europe, contact your Fujitsu Siemens Computers branch office/subsidiary or our recycling centre in Paderborn: Fujitsu Siemens Computers...

  • Page 35: Installing The Server

    Installing the Server Installation Steps Installing the Server Installation Steps CAUTION! Please take note of the safety information in the chapter “Important Notes” on page 17. Do not expose the server to extreme environmental conditions (see section “Technical Data” on page 14). Protect it from dust, humidity and heat.

  • Page 36: Unpacking The Server

    Unpacking the Server Installing the Server Unpacking the Server CAUTION! Please take note of the safety information in the chapter “Important Notes” on page 17. Ask somebody for help with carrying the server. Do not unpack the server until it is at its installation location. It is recommended not to throw away the original packaging material! It may be required for transport at some later date.

  • Page 37: Mounting The Server In The Rack

    Installing the Server Mounting the Server in the Rack Mounting the Server in the Rack CAUTION! Please take note of the safety information and the notes on mounting the server in the rack in the chapter “Important Notes” on page 17. At least two people are needed to position the server in the rack.
  • Page 38 Mounting the Server in the Rack Installing the Server Ê Mount the support bracket on the corresponding height of the rear left support upright, using the two screws delivered. Ê Fasten the two telescopic rails to the support uprights/the support bracket in the rack, using the 8 screws delivered with the system.
  • Page 39 Installing the Server Mounting the Server in the Rack Ê Pull the telescope bars completely out toward the front. They must click into place so that you can no longer push them back. Ê Lift the server onto the two projecting telescope bars (see figure 6), carrying it by the handles.
  • Page 40 Mounting the Server in the Rack Installing the Server Ê Release the safety catch (see magnifying view in figure 7) on both telescope bars by pushing it upwards in the direction of the arrow, and slide the server into the rack. Figure 7: Mounting the server into the rack U41621-J-Z156-1-76...
  • Page 41 Installing the Server Mounting the Server in the Rack Ê Fasten the system unit to the rack using the two knurled screws (1) on the front side. Figure 8: Fastening the server to the rack Removing the server is performed in reverse order. U41621-J-Z156-1-76...

  • Page 42: Connecting And Disconnecting Cables

    Connecting and Disconnecting Cables Installing the Server Connecting and Disconnecting Cables CAUTION! Observe the safety information in the chapter “Important Notes” on page 17. Never connect or disconnect cables during thunderstorms. When disconnecting a cable, always grasp the plug. Never pull on the cable! Read the documentation for an external device before you connect it.

  • Page 43: Connecting Devices To The Server

    Ê If necessary, update the BIOS code and the service processor firmware. To download the most current level of BIOS code and service processor firmware, go to www.fujitsu-siemens.com/support. Ê Make sure that the service processor on each node is configured and connected to the network.
  • Page 44 Connecting and Disconnecting Cables Installing the Server Two-node Configuration A two-node configuration requires two 2.3-m (7.6-foot) scalability cable kits. To cable a two-node configuration for up to 8-way operation, complete the following steps: Ê Remove the protective covers from the connectors on the ends of the cables (figure 9).
  • Page 45 Installing the Server Connecting and Disconnecting Cables Figure 11: Cabling two nodes Ê Connect the SMP Expansion cables to node 1: Ê Connect one end of an SMP Expansion cable to port 1 on node 1; then, route the cable through the node 1 cable-management arm. Use a 2.3- m (7.6-foot) SMP Expansion cable for this connection.
  • Page 46 Connecting and Disconnecting Cables Installing the Server Four-node configuration A four-node configuration requires three 2.3-m (7.6-foot) scalability cable kits and three 2.9-m (9.5-foot) scalability cable kits. To cable a four-node configu- ration for up to 16-way operation, complete the following steps: Ê...
  • Page 47 Installing the Server Connecting and Disconnecting Cables Connect the SMP Expansion cables to node 1: Ê Connect one end of an SMP Expansion cable to port 1 on node 1; then, route the cable through the node 1 cable-management arm. Use a 2.9- m (9.5-foot) SMP Expansion cable for this connection.

  • Page 48: Power Cabling

    Connecting and Disconnecting Cables Installing the Server Ê Locate the SMP Expansion cable that is connected to port 2 on node 2; then, connect the opposite end of the cable to port 2 of node 4. Next, route the cable through the node 4 cable-management arm. Ê...
  • Page 49 Installing the Server Connecting and Disconnecting Cables Ê Connect a power supply cord to one of the system power connectors on the rear of the server. Ê Plug the other end of the power supply cord into a properly grounded electrical outlet or a primary power unit inside the rack.

  • Page 51: Preparation For Operation

    Preparation for Operation CAUTION! Observe the safety information in the chapter “Important Notes” on page 17. Controls and Indicators 4.1.1 Front View Figure 14: Front view U41621-J-Z156-1-76...
  • Page 52 Controls and Indicators Preparation for Operation HDD Status LED – When this LED is lit, it indicates that the associated hard disk drive has failed (HDD FAULT). – If the LED flashes slowly (one flash per second), the drive is being rebuilt. –...

  • Page 53: Rear View

    Preparation for Operation Controls and Indicators 12 Power-on LED – When this LED is lit and not flashing, it indicates that the server is turned on. – When this LED is flashing, it indicates that the server is turned off and still connected to an AC power source.
  • Page 54 Controls and Indicators Preparation for Operation USB Port 1 and 2 This is an automatically configured port that you can use to connect one or more USB devices to the server, using Plug and Play technology. System Serial Port (RS232) Connect an optional 9-pin serial device to this connector.
  • Page 55 Preparation for Operation Controls and Indicators LEDs and indicators Figure 16: Rear view of server (LEDs and indicators) AC LED for PS1 When these LEDs are lit, the server is con- nected to the mains. AC LED for PS2 Service Processor Ethernet When this LED is lit, it indicates that there 10/100 link indicator is an active connection on the Ethernet...
  • Page 56 Controls and Indicators Preparation for Operation I/O board error LED When this LED is lit, it indicates that there is a problem with the I/O board. Gigabit Ethernet 2 activity When this LED is lit, it indicates that there is activity between the server and the net- work.

  • Page 57: Switching The Server On And Off

    Preparation for Operation Switching the Server On and Off Switching the Server On and Off CAUTION! If after switching on the server there is nothing but flickering stripes on the screen, switch the server off immediately (see the chapter “Trouble- shooting and Tips”...

  • Page 58: Switching Off The Server

    Switching the Server On and Off Preparation for Operation When the server is powered on, the Power-on LED switches from blinking mode (standby) to a solid light. If the server is switched on and a power failure occurs, it restarts automatically when power is restored.
  • Page 59 Preparation for Operation Switching the Server On and Off If the server is installed in a multi-node configuration, pressing the power button on the primary node in the partition will start an orderly shutdown of the operating system and turn off the server. The server can be turned off from the RSA-II user interface (see the RSA-II user manual for more details).

  • Page 60: Configuring The Server

    Configuring the Server Preparation for Operation Configuring the Server 4.3.1 BIOS Setup Using the Configuration/Setup Utility program Configuration/Setup is a menu-driven utility that is part of the basic input/output system (BIOS) code that comes with your server. You can use it to: View configuration information View and change assignments for devices and I/O ports Set the date and time...
  • Page 61 Preparation for Operation Configuring the Server Choices Available from the Configuration/Setup Main Menu From the Configuration/Setup Utility main menu, you can select settings that you want to change. The Configuration/Setup Utility main menu is similar to figure 17. Depending on the administrator password entered, you will either see a full or a limited menu.
  • Page 62 Configuring the Server Preparation for Operation System Summary Select this choice to view configuration information, including the type, speed, and cache sizes of the microprocessors, type and speed of installed USB devices, and the amount of installed memory. When you make configuration changes through other options in the Configu- ration/Setup Utility program, the changes are reflected in the system summary;...
  • Page 63 Preparation for Operation Configuring the Server If you disable the integrated USB controller, the server will have no USB capability; to maintain USB capability, make sure that Enable is selected for the USB Host Controller and USB BIOS Legacy Support options. If the USB host controller is disabled, the RSA-II remote keyboard, remote mouse, remote disk, OS watchdog, and in-band management functions are also disabled.
  • Page 64 Select this choice to identify if the System Partition is visible. To make the System Partition visible, set this value to Visible. To make the System Partition invisible, set this value to Hidden. Default value is Hidden. This function is not operable for PRIMERGY RX800 S2. U41621-J-Z156-1-76...
  • Page 65 Preparation for Operation Configuring the Server Memory Settings Select this choice to manually enable bank of memory and to enable or disable Memory Mirroring. If a memory error is detected during POST or memory configuration, the server can automatically disable the failing memory bank and continue operating with reduced memory capacity.
  • Page 66 Configuring the Server Preparation for Operation Baseboard management controller (BMC) settings Select this choice to view information and to change baseboard management controller (BMC) settings. – BMC firmware Version This is a nonselectable menu item that displays the BMC firmware version.
  • Page 67 Preparation for Operation Configuring the Server Event/Error Logs Select this choice to view or clear error logs. – POST Error Log Select this choice to view the three most recent error codes and messages that the system generated during POST. Select Clear error logs from the POST Error Log menu to clear the error log.

  • Page 68: Using The Boot Menu Program

    Configuring the Server Preparation for Operation 4.3.2 Using the Boot Menu Program The Boot Menu program is a built-in configuration program that you can use to temporarily redefine the first startup device without changing settings in the Configuration/Setup Utility program. To use the Boot Menu program, complete the following steps: Ê...
  • Page 69 Preparation for Operation Configuring the Server A user who types the power-on password has access to only the limited Config- uration/Setup Utility menu; the user can set, change, and delete the power-on password, if the system administrator has given the user that authority. Preventing unauthorized BIOS Setup calls (admin password) You can activate this protection by setting an administrator password in the System Security menu.

  • Page 70: Configuring The Gigabit Ethernet Controller

    Configuring the Server Preparation for Operation 4.3.4 Configuring the Gigabit Ethernet Controller The Ethernet controller is integrated on the I/O board. It provides an interface for connecting to a 10-Mbps, 100-Mbps, or 1-Gbps network and provides full- duplex (FDX) capability, which enables simultaneous transmission and reception of data on the network.
  • Page 71 Preparation for Operation Configuring the Server PXE boot agent utility menu choices The following choices are on the PXE boot agent utility menu: Boot Protocol PXE is the default setting. Do not change this setting; the server does not support any other network boot protocols. Boot Strap Type Select this choice to specify the type of boot strap.

  • Page 72: Using The Sas Configuration Utility Program

    Configuring the Server Preparation for Operation 4.3.6 Using the SAS Configuration Utility program Use the SAS Configuration Utility program to configure SAS devices. This program is described in more detail in the ServeRAID-8i user manual. Starting the SAS Configuration Utility program To start the SAS Configuration Utility program, complete the following steps: Ê...

  • Page 73: Scalable-Partition Configuration

    Preparation for Operation Configuring the Server 4.3.8 Scalable-partition configuration The Scalable Partition Web Interface is an extension of the RSA-II Web Interface and is used to create, delete, control, and view scalable partitions. The Scalable Partition Web Interface is in the RSA-II integrated service processor. The scalable partition defines a multi-node configuration, which interconnects two or four servers.The multi-node configuration provides the function to individ- ually power-on and power-off each node.
  • Page 74 Configuring the Server Preparation for Operation Ê Access the network used by the multi-node configuration and connect and log in to the RSA-II Web Interface on the primary node. See the RSA-II user manual for more information; then, continue with the procedure to create a scalable partition.
  • Page 75 Preparation for Operation Configuring the Server Ê In the navigation pane, click Create Partition. Only perform this step if you are cabling the configuration or changing the host name. Use the Create Scalable Partitions Settings page to create new scalable partitions. A page similar to the one in the following illustration is displayed.
  • Page 76 Configuring the Server Preparation for Operation Ê Use the Create Scalable Partition Settings page to define the scalable partition. Perform this step to create a new partition. A page similar to the one in the following illustration is displayed. Ê In the Partition merge timeout minutes field, select the number of minutes POST waits for the scalable nodes to merge resources.

  • Page 77: Installing The Operating System

    Preparation for Operation Configuring the Server Ê In the Scalable Partition Members field, select the nodes that will be assigned to the scalable partition. You can select all nodes or select individual nodes. Ê Click Create. Ê In the navigation pane, click Control Partition and follow the instructions on the Control Scalable Partition page to manage the scalable partition.

  • Page 78: 4.3.10 Installing And Using The Bmc Utility Programs

    Configuring the Server Preparation for Operation If your server is equipped with an optional disk array controller (RAID adapter), please read in the appropriate manual how to configure the disk array before you install the desired system. To install the operating system: Ê...
  • Page 79 Updating and configuring the BIOS Ê Update the BIOS code: Ê Download the latest version of the BIOS code from http://www.fujitsu-siemens.com/support/. Ê Update the BIOS code, following the instructions that come with the update file that you downloaded. Ê Configure the BIOS settings: Ê...
  • Page 80 Configuring the Server Preparation for Operation Remote Console Stop Bits: 1 Remote Console Text Emulation: ANSI Remote Console Keyboard Emulation: ANSI Remote Console Active After Boot: Enabled Remote Console Flow Control: Hardware Ê Press [ESC] twice to exit the Remote Console Redirection and Devices and I/O Ports sections of the Configuration/Setup Utility program.
  • Page 81 Preparation for Operation Configuring the Server This procedure is based on a default installation of Red Hat Enterprise Linux ES 2.1. The file names, structures, and commands might be different for other versions of Red Hat Linux. To configure the general Linux parameters for SOL operation when using the Red Hat Enterprise Linux ES 2.1 operating system, complete the following steps.

  • Page 82: U41621-J-Z156

    Configuring the Server Preparation for Operation initrd=/boot/initrd-2.4.9-e.12smp.img read-only root=/dev/hda6 append="console=tty1 console=ttyS1,19200n8 " The following examples show the original content of the /etc/lilo.conf file and the content of this file after modification. Original /etc/lilo.conf contents prompt timeout=50 default=linux boot=/dev/hda map=/boot/map install=/boot/boot.b message=/boot/message linear image=/boot/vmlinuz-2.4.9-e.12smp...
  • Page 83 Preparation for Operation Configuring the Server Modified /etc/lilo.conf contents prompt timeout=50 default=linux-Monitor boot=/dev/hda #map=/boot/map install=/boot/boot.b #message=/boot/message linear # This will allow you to only Monitor the OS boot via SOL image=/boot/vmlinuz-2.4.9-e.12smp label=linux-Monitor initrd=/boot/initrd-2.4.9-e.12smp.img read-only root=/dev/hda6 append="console=ttyS1,19200n8 console=tty1" # This will allow you to Interact with the OS boot via SOL image=/boot/vmlinuz-2.4.9-e.12smp label=linux-Interact initrd=/boot/initrd-2.4.9-e.12smp.img...
  • Page 84 Configuring the Server Preparation for Operation Ê Append the following text to the kernel/ line of the first title= section: console=ttyS1,19200 console=tty1 Ê Add the following five lines between the two title= sections: # This will allow you to Interact with the OS boot via SOL title Red Hat Linux (2.4.9-e.12smp) SOL Interactive root (hd0,0) kernel /vmlinuz-2.4.9-e.12smp ro root=/dev/hda6...
  • Page 85 Preparation for Operation Configuring the Server Modified /boot/grub/grub.conf contents #grub.conf generated by anaconda # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that all kernel and initrd paths are relative to /boot/, eg. root (hd0,0) kernel /vmlinuz-version ro root=/dev/hda6 initrd /initrd-version.img...
  • Page 86 Configuring the Server Preparation for Operation Ê Add the following line after the tty6 line at the bottom of the /etc/securetty file to enable a user to log in as the root user through the SOL console: ttyS1 Ê Complete the following steps to modify the /boot/grub/menu.lst file: Ê...
  • Page 87 Preparation for Operation Configuring the Server Original /boot/grub/meu.lst contents disableapic maxcpus=0 3 initrd (hd0,1)/boot/initrd.shipped Modified /boot/grub/menu.lst contents #gfxmanu (hd0,1)/boot/message color white/blue black/light-gray default 0 timeout 8 # This will allow you to only Monitor the OS boot via SOL title linux SOL Monitor kernel (hd0,1)/boot/vmlinuz root=/dev/hda2 acpi=oldboot vga=791 console=ttyS1,19200 console=tty1 initrd (hd0,1)/boot/initrd...
  • Page 88 Configuring the Server Preparation for Operation Complete the following steps to configure the Windows 2003 operating system for SOL operation. You must be logged in as a user with administrator access to perform this procedure. Ê Determine which boot entry ID to modify: Ê...
  • Page 89 Complete the following steps to install the OSA SMBridge management utility program on a server running a Windows operating system: Ê Go to http://www.fujitsu-siemens.com/support/, download the utility program, and create the OSA BMC Management Utility CD. Ê Insert the OSA BMC Management Utility CD into the drive.

  • Page 90: 4.3.11 Using The Bmc Utility Programs

    Configuring the Server Preparation for Operation Alternatively, you can use the ServerStart CD. Ê Type mount /mnt/cdrom. Ê Locate the directory where the installation RPM package is located and type cd /mnt/cdrom. Ê Type the following command to run the RPM package and start the instal- lation: rpm -i osabmcutil-1.0-i386.rpm Ê...
  • Page 91 Preparation for Operation Configuring the Server Copy the bmc_cfg.exe file from the ServerStart CD to a configuration utility diskette on a USB connected diskette drive. To start the baseboard management controller configuration utility program, complete the following steps: Ê Insert the configuration utility diskette into the USB diskette drive and restart the server.
  • Page 92 Configuring the Server Preparation for Operation – power Turn the server on and off remotely. – sel Perform operations with the BMC system event log. – sysinfo Display general system information that is related to the server and the baseboard management controller. Serial over LAN Use the Serial over LAN capability to remotely perform control and management functions over a Serial over LAN (SOL) network.

  • Page 93: Cleaning The Server

    Cleaning the Server Cleaning the Server CAUTION! Switch the server off, and pull the power plugs out of the grounded- contact power sockets. Do not clean any interior parts yourself; leave this job to a service technician. Do not use any cleaning agents that contain abrasives or may corrode plastic.

  • Page 95: Troubleshooting And Tips

    Troubleshooting and Tips This chapter provides basic troubleshooting information to help you resolve some common problems that might occur with your PRIMERGY RX800 S2. CAUTION! Take note of the safety notes in the “Safety” manual and in the chapter “Important Notes” on page 17 and chapter “Installing the Server” on page 29, when you connect or disconnect cables.

  • Page 96: Error Controls And Indicators

    Error Controls and Indicators Troubleshooting and Tips Error Controls and Indicators 5.1.1 Light Path Diagnostics Light path diagnostics is a system of LEDs on various external and internal components of the server. When an error occurs, LEDs are lit throughout the server.

  • Page 97: Operator Information Panel

    Troubleshooting and Tips Error Controls and Indicators 5.1.2 Operator Information Panel Figure 19: Operator Information Panel USB 1.1 connector The connectors, buttons and LEDs labelled 1 through 5 are are not pertinent in this context Power-on LED and are only listed for the sake of completeness. Power Button In general, their designations speak for them- selves.

  • Page 98: Led Card

    Error Controls and Indicators Troubleshooting and Tips 5.1.3 LED Card The LED Card is located inside the Operator Information Panel. Proceed as follows: Ê Press the release latch on the front of the Operator Information Panel to the left (see pos. 8 in figure 19). Ê...
  • Page 99 Troubleshooting and Tips Error Controls and Indicators Light Path Diagnostic LEDs The following table describes the LEDs on the LED card and suggested actions to correct the detected problems. Lit LED on Cause Action LED Card All LEDs No action necessary. are off (the power LED is lit).
  • Page 100 Error Controls and Indicators Troubleshooting and Tips Lit LED on Cause Action LED Card LINK There is a fault in an SMP Ê Check the SMP Expansion Port Expansion Port or SMP link LEDs to find the failing port Expansion cable. or cable.
  • Page 101 Troubleshooting and Tips Error Controls and Indicators Lit LED on Cause Action LED Card Information is present in the Ê Save the log if necessary and BMC log and system-error clear it (see “Event/Error Logs” log. One or both logs might on page 61).
  • Page 102 Error Controls and Indicators Troubleshooting and Tips Lit LED on Cause Action LED Card DASD A hard disk drive has failed Ê Reinstall the removed drive. or has been removed. Ê If an individual HDD LED is lit, The error LED on the replace the HDD (see failing hard disk drive page 106).
  • Page 103 Troubleshooting and Tips Error Controls and Indicators Lit LED on Cause Action LED Card A fan has failed or has been Ê Reinstall the removed fan. removed. Ê If an individual fan LED is lit, A failing fan can also replace the fan (see page 112).

  • Page 104: Miscellaneous Problems

    Miscellaneous Problems Troubleshooting and Tips Miscellaneous Problems 5.2.1 Power-on Indicator Remains Dark The power-on indicator remains dark after switching ON: Power cable not connected correctly Ê Make sure that the power cables are correctly connected to the server and to the grounded power sockets. Power supply overloaded Ê...

  • Page 105: Flickering Stripes Across The Monitor

    Troubleshooting and Tips Miscellaneous Problems Brightness control is set too dark Ê Adjust the brightness control to increase the brightness. For detailed infor- mation, please refer to the operating manual supplied with your monitor. Power cable or monitor cable not connected Ê...

  • Page 106: No Monitor Display Or Display Drifts

    Miscellaneous Problems Troubleshooting and Tips 5.2.5 No Monitor Display or Display Drifts The wrong horizontal frequency and/or resolution has been selected for the monitor or for the application program. Ê Find out which horizontal frequency your monitor supports. You will find the horizontal frequency (also known as line frequency or horizontal deflection frequency) in the documentation for your monitor.

  • Page 107: Added Drive Defective

    Troubleshooting and Tips Miscellaneous Problems 5.2.9 Added Drive Defective RAID controller is not configured for this hard disk drive The drive was installed with the system switched OFF. Ê Reconfigure the RAID controller for the drive with the corresponding utility. Information is contained in the documentation on the RAID controller.

  • Page 109: Hot-Plug Components

    Hot-plug Components This chapter describes how to handle hot-plug components and/or how to modify your server hardware. The hot-plug procedure (replacing and adding components while the system is operating) enhances the availability of system operation, ensuring a high degree of data security and system stability. First, hot-plug components are described which are directly accessible from the outside: HDD modules.

  • Page 110: Hot-Plug Hard Disk Drives

    HDD modules Hot-plug Components Hot-plug Hard Disk Drives Up to six SAS hard disk drives can be installed into the PRIMERGY RX800 S2 server. The hard disk drives are built on a carrier which allows defective drives to be replaced or new drives to be added during operation. The hard disk drive and the carrier constitute the hard disk drive module (called "HDD module"...

  • Page 111: Handling Hdd Modules

    Hot-plug Components HDD modules 6.1.1 Handling HDD Modules Hard disk drives incorporated in the HDD modules are highly sensitive electro- magnetic devices and must be handled with great care. It is extremely likely that an incorrect handling will lead to a partially and/or total failure of the hard disk drives.

  • Page 112: Installing A Hot-Plug Hdd Module

    HDD modules Hot-plug Components 6.1.2 Installing a hot-plug HDD module To install a hot-plug HDD module, complete the following steps: Ê Remove the dummy module from one of the empty hot-plug bays (see figure 21). Ê Alternatively, if a defective HDD module is to be hot-swapped, remove it from its bay.
  • Page 113 Hot-plug Components HDD modules Ê Touch the static-protective package that contains the HDD module to any unpainted surface on the outside of the serve; then, remove the HDD module from the package. Ê Make sure that the module handle is open; then, install the HDD module into the hot-plug bay in the direction of the arrow (see figure 22).

  • Page 114: Removing The Cover

    Removing the Cover Hot-plug Components Removing the Cover CAUTION! The actions described in these instructions should only be performed by technical specialists. Equipment repairs should only be performed by authorized, qualified staff. Any unauthorized openings and improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) and could also damage the equipment.
  • Page 115 Hot-plug Components Removing the Cover CAUTION! While the system is running, the cover must be reinstalled as soon as possible (max. 2 minutes) due to cooling, to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and to protect against fire. Ê...

  • Page 116: Replacing A Hot-Plug Power Supply

    Hot-plug power supplies Hot-plug Components Replacing a hot-plug power supply The server has two hot-plug power supply units installed, ensuring a redundant power supply. If one unit fails, the other unit ensures unimpaired further operation. The defective power supply unit can be replaced during operation. CAUTION! Before replacing a non-defective hot-plug power supply unit in a non- redundant configuration (only one power supply unit present), the server...
  • Page 117 Hot-plug Components Hot-plug power supplies Ê Connect one end of the power cord for the new power supply into the connector on the back of the power supply; route the power cord through the cable-management arm and connect the other end of the power cord into a properly grounded electrical outlet.

  • Page 118: Replacing A Hot-Plug System Fan Unit

    Hot-plug Components Replacing a Hot-plug System Fan Unit The PRIMERGY RX800 S2 server comes with four 80-mm hot-plug fans in front of the PCI-X slots and four 92-mm hot-plug fans in front of the memory cards (overview: see figure 24 on page 109). The following removal and installation procedures apply to either size fan.
  • Page 119 Hot-plug Components System Fans Hot-plug fan 5 Hot-plug fan 6 Fan Error Hot-plug fan 7 Hot-plug fan 8 Hot-plug fan 1 Hot-plug fan 2 Hot-plug fan 3 Hot-plug fan 4 Figure 26: Replacing hot-plug fans (server front shown without bezel) U41621-J-Z156-1-76...

  • Page 120: Hot-Plug Memory Cards

    – Hot-add: Inserting new memory cards into empty slots (see page 117). – Hot-replace: Replacing memory cards (see page 118). In order to get a better understanding of the PRIMERGY RX800 S2 memory concept, you should first read the following sections “Active Memory” on page 114 and “Memory Card Introduction”...
  • Page 121 Hot-plug Components Memory Cards Ê Enable the memory mirroring setting from within this window. Ê Save and exit the Configuration/Setup Utility program. When memory mirroring is enabled, the data that is written to memory is stored in two locations. One copy is kept in the memory port 1 DIMMs, while a second copy is kept in the memory port 2 DIMMs.

  • Page 122: Memory Card Introduction

    Memory Cards Hot-plug Components 6.5.2 Memory Card Introduction The server supports up to four memory cards. Each memory card holds up to four DIMMs. There must be at least one memory card with one pair of DIMMs installed for the server to operate. There are two memory power buses split between the four memory cards.

  • Page 123: Adding And Replacing A Memory Card

    Hot-plug Components Memory Cards 6.5.3 Adding and replacing a memory card CAUTION! Both hot-add and hot-replace must be activated in BIOS setup and supported by the operation system. Otherwise, no hot-plug operations are possible. The server must then be shut down before the operation can be started.
  • Page 124 Memory Cards Hot-plug Components Ê Grasp the memory card by the retention levers and turn the memory card so that the connector aligns with the connector on the microprocessor board. Ê Insert the memory card into the memory card connector. Ê...
  • Page 125 Hot-plug Components Memory Cards Figure 28: Removing a memory card Ê Replace the memory card: Ê Grasp the memory card by the retention levers and turn the memory card so that the connector aligns with the connector on the microprocessor board.

  • Page 126: Hot-Plug Pci/Pci-X Adapters

    Hot-plug Components Hot-plug PCI/PCI-X Adapters CAUTION! Each PCI-X slot of the PRIMERGY RX800 S2 server must be occupied by either a PCI/PCI-X adapter or an extension-slot cover. The following operations are possible while the system is running: – Adding PCI/PCI-X adapters (see “Installing a hot-plug PCI/PCI-X adapter”...

  • Page 127: Installing A Hot-Plug Pci/Pci-X Adapter

    Hot-plug Components PCI/PCI-X Adapters 6.6.2 Installing a hot-plug PCI/PCI-X adapter To change the order in which the server scans devices and PCI-X slots, start the Configuration/Setup Utility program and select Start Options from the main menu. See “Using the Configuration/Setup Utility program” on page 54.
  • Page 128 PCI/PCI-X Adapters Hot-plug Components Adapter Attention retention latch (yellow) PCI-X retaining Power PCI-X divider (green) Figure 29: Installing a hot-plug PCI/PCI-X adapter (server front shown without bezel) Ê Install the adapter: Ê Open the blue PCI-X retaining bar by lifting the front edge. Ê...
  • Page 129 Hot-plug Components PCI/PCI-X Adapters Ê Grasp the adapter by the top edge or upper corners of the adapter and remove it from the package. Ê Carefully grasp the adapter by its top edge or upper corners, and align it with the connector on the PCI-X board. Ê...

  • Page 130: Replacing A Hot-Plug Pci/Pci-X Adapter

    PCI/PCI-X Adapters Hot-plug Components Ê Press the adapter firmly into the adapter connector. Ê Push down on the blue PCI-X retaining bar to stabilize the adapter. Ê Close the tab; then, push down on the orange adapter retention latch until it clicks into place, securing the adapter. Ê...

  • Page 131: Abbreviations

    Abbreviations Automatic BIOS recovery Alternating Current ACPI Advanced Configuration and Power Interface ANSI American National Standards Institute ASR&R Automatic Server Reconfiguration and Restart Battery Backup Unit BIOS Basic Input-Output System BIST Built-in Self Test Baseboard Management Controller British Thermal Unit Cache Coherency Compact Disk CD-ROM...
  • Page 132 Abbreviations Cylinder Head Sector CMOS Complementary Metal Oxide Semiconductor Communications CPLD Complex Programmable Logic Device Central Processing Unit DASD Direct Access Storage Device Direct Current DIMM Dual Inline Memory Module Dual Inline Package Direct Memory Access Desktop Management Interface Digital Versatile Disk Errror Checking and Correcting Extended Capabilities Port U41621-J-Z156-1-76...
  • Page 133 Abbreviations EEPROM Electrically Erasable Programmable Read-Only Memory Extensible Firmware Interface Electronic Industries Alliance Electromagnetic Compatibility Emergency Management Port Enhanced Parallel Port EPROM Erasable Programmable Read-Only Memory ElectroStatic Discharge File Allocation Table Front Panel Controller Field Replaceable Unit Front Side Bus Global Array Manager Graphical User Interface U41621-J-Z156-1-76...
  • Page 134 Abbreviations Hard Disk Drive Hot-Swap Controller Height Unit I²C Inter-Integrated Circuit Input/Output Intelligent Chassis Management Identification Integrated Drive Electronics International Electrotechnical Commission Integrated Mirroring Enhanced IPMI Intelligent Platform Management Interface Interrupt Request Line Internet Exchange Architecture Local Area Network U41621-J-Z156-1-76...
  • Page 135 Abbreviations Logical Block Address Liquid Crystal Display Light Emitting Diode Low Profile Logical Unit Number Low-Voltage Differential SCSI Manual Retention Latch Multi Mode Faser Non Maskable Interrupt NTFS New Technology File System NVRAM Non Volatile Random Access Memory Operating System Promise Array Management Peripheral Component Interconnect U41621-J-Z156-1-76...
  • Page 136 Abbreviations Prefailure Detection and Analysing Portable Data Format Predictive Failure Analysis Physical Layer Protocol, Physical Layer Device POST Power ON Self Test PS/2 Personal System/2 Power Supply Unit Preboot Execution Environment RAID Redundant Arrays of Independent Disks Random Access Memory RoHS Restriction of the Use of Certain Hazardous Substances (Waste from Electric and Electronic Equipment, EU Directive)
  • Page 137 Abbreviations Real Time Clock RTDS Remote Test- und Diagnose-System SAF-TE SCSI Accessed Fault-Tolerance Enclosures Serial Attached SCSI SATA Serial Advanced Technology Attachment Single Bit Error Single Connector Attachment SCSI Small Computer System Interface System Configuration Utility Sensor Data Record SDRAM Synchronous Dynamic Random Access Memory System Event Log S.M.A.R.T...
  • Page 138 Abbreviations Symmetrical Multiprocessor Service Processor Serial Presence Detect System Setup Utility SVGA Super Video Graphics Adapter Uninterruptible Power Supply Universal Serial Bus Video Graphics Adapter Vital product data WEEE Waste from Electric and Electronic Equipment (EU Directive) Wakeup on LAN Zero Channel RAID U41621-J-Z156-1-76...

  • Page 139: Related Publications

    Safety Technical Manual Ergonomics Technical Manual Warranty Technical Manual PRIMERGY RX800 S2 Options Guide Quickstart Hardware - PRIMERGY RX800 S2 Poster Quickstart Software - PRIMERGY ServerView Suite Poster PRIMERGY RX800 S2 RemoteView Management Board RSA-II User Manual PRIMERGY RX800 S2...
  • Page 140 Related publications [10] PRIMERGY ServerView Suite RemoteView User Manual [11] PRIMERGY ServerView Suite ServerView S2 Server Management User Manual [12] PRIMERGY ServerView Suite ServerView Server Management User Manual [13] 19-Zoll-Rack/19 inch rack Technical Manual [14] DataCenter Rack Technical Manual U41621-J-Z156-1-76...

  • Page 141: Index

    Index acclimatization time 105 date and time, setting 57 administrator password 63 dimensions 14 advanced setup 58 documents related to this manual 3 drive defective 101 BIOS setup 54 drive features 11 preventing calls 63 security functions 62 boot precedence 58 electrical data 14 buttons electromagnetic compatibility 15, 23...
  • Page 142 Index gigabit ethernet port 48 keyboard port 48 hard disk drive LED card 92 carrier 104 LED diagnostic path 6 handling 105 light-emitting diode (LED) 21 HDD module 104 lithium battery 20 hot-plug 104 locator light 91 hard disk subsystem 6 logs HDD Activity Light 91 error logs 61...
  • Page 143 Index mounting 31 PCI configuration 58 on/off 51 PCI-X adapter slots 11 ports 37 PCI-X slot information 59 switches itself off (error) 98 PCI-X slots 7 transport 24 performance 4 unpacking 30 ports ServerStart 7 gigabit ethernet port 48 ServerView 7 keyboard port 48 supported functions 8 USB port 46, 48...
  • Page 145 Comments Fujitsu Siemens Computers GmbH User Documentation 33094 Paderborn Suggestions Germany Corrections Fax: (++49) 700 / 372 00001 email: manuals@fujitsu-siemens.com http://manuals.fujitsu-siemens.com Submitted by Comments on PRIMERGY RX800 S2 Operating Manual U41621-J-Z156-1-76...
  • Page 147 Comments Fujitsu Siemens Computers GmbH User Documentation 33094 Paderborn Suggestions Germany Corrections Fax: (++49) 700 / 372 00001 email: manuals@fujitsu-siemens.com http://manuals.fujitsu-siemens.com Submitted by Comments on PRIMERGY RX800 S2 Operating Manual U41621-J-Z156-1-76...
  • Page 149 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu- ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So- lutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed.

Table of Contents