H3C S3600 Series Command Manual
  1. Manuals
  2. Brands
  3. H3C Manuals
  4. Network Router
  5. H3C S3600 Series
  6. Command manual
H3C S3600 Series Command Manual

H3C S3600 Series Command Manual

Multicast
Hide thumbs Also See for S3600 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Command Manual, Operating Manual
Command Manual - Multicast
H3C S3600 Series Ethernet Switches-Release 1510
Chapter 1 IGMP Snooping Configuration Commands............................................................... 1-1
1.1 IGMP Snooping Configuration Commands ....................................................................... 1-1
1.1.1 display igmp-snooping configuration....................................................................... 1-1
1.1.2 display igmp-snooping group .................................................................................. 1-2
1.1.3 display igmp-snooping statistics.............................................................................. 1-3
1.1.4 igmp-snooping......................................................................................................... 1-4
1.1.5 igmp-snooping fast-leave ........................................................................................ 1-5
1.1.6 igmp-snooping general-query source-ip ................................................................. 1-6
1.1.7 igmp-snooping group-limit....................................................................................... 1-7
1.1.8 igmp-snooping group-policy .................................................................................... 1-8
1.1.9 igmp-snooping host-aging-time............................................................................. 1-10
1.1.10 igmp-snooping max-response-time..................................................................... 1-11
1.1.11 igmp-snooping querier ........................................................................................ 1-12
1.1.12 igmp-snooping query-interval.............................................................................. 1-12
1.1.13 igmp-snooping router-aging-time ........................................................................ 1-13
1.1.14 reset igmp-snooping statistics............................................................................. 1-14
1.1.15 service-type multicast.......................................................................................... 1-14
Chapter 2 Common IP Multicast Configuration Commands..................................................... 2-1
2.1 Common IP Multicast Configuration Commands............................................................... 2-1
2.1.1 display mpm forwarding-table ................................................................................. 2-1
2.1.2 display mpm group.................................................................................................. 2-2
2.1.3 display multicast forwarding-table ........................................................................... 2-3
2.1.4 display multicast routing-table................................................................................. 2-5
2.1.5 display multicast-source-deny................................................................................. 2-6
2.1.6 multicast route-limit ................................................................................................. 2-7
2.1.7 multicast routing-enable .......................................................................................... 2-8
2.1.8 multicast-source-deny ............................................................................................. 2-9
2.1.9 reset multicast forwarding-table ............................................................................ 2-10
2.1.10 reset multicast routing-table ................................................................................ 2-11
Chapter 3 Multicast MAC Address Entry Configuration Commands....................................... 3-1
3.1 Multicast MAC Address Entry Configuration Commands .................................................. 3-1
3.1.1 mac-address multicast interface ............................................................................. 3-1
3.1.2 mac-address multicast vlan..................................................................................... 3-2
3.1.3 display mac-address multicast static....................................................................... 3-2
Chapter 4 Unknown Multicast Drop Configuration Command ................................................. 4-1
4.1 Unknown Multicast Drop Configuration Command............................................................ 4-1
4.1.1 unknown-multicast drop enable .............................................................................. 4-1

Table of Contents

i
Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S3600 Series and is the answer not in the manual?

Questions and answers

Related Manuals for H3C S3600 Series

Summary of Contents for H3C S3600 Series

  • Page 1: Table Of Contents

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Table of Contents Table of Contents Chapter 1 IGMP Snooping Configuration Commands............... 1-1 1.1 IGMP Snooping Configuration Commands ............... 1-1 1.1.1 display igmp-snooping configuration............... 1-1 1.1.2 display igmp-snooping group .................. 1-2 1.1.3 display igmp-snooping statistics................
  • Page 2 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Table of Contents Chapter 5 IGMP Configuration Commands ................5-1 5.1 IGMP Configuration Commands..................5-1 5.1.1 display igmp group ....................5-1 5.1.2 display igmp interface ..................... 5-2 5.1.3 igmp enable......................5-3 5.1.4 igmp group-limit.......................
  • Page 3 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Table of Contents Chapter 7 MSDP Configuration Commands ................7-1 7.1 MSDP Configuration Commands..................7-1 7.1.1 cache-sa-enable...................... 7-1 7.1.2 display msdp brief ....................7-1 7.1.3 display msdp peer-status ..................7-2 7.1.4 display msdp sa-cache....................

  • Page 4: Chapter 1 Igmp Snooping Configuration Commands

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Chapter 1 IGMP Snooping Configuration Commands Note: AmongS3600 series Ethernet switches,S3600-EI series support all the multicast protocols listed in this manual, whileS3600-SI series only support IGMP Snooping An Ethernet switch serves as a router when an IP multicast protocol is running on it.

  • Page 5: Display Igmp-Snooping Group

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Enable IGMP-Snooping. The router port timeout is 105 second(s). The max response timeout is 10 second(s). The host port timeout is 260 second(s). The above-mentioned information shows: IGMP Snooping is enabled, the aging time of the router port is 105 seconds, the query response timeout time is 10 seconds, and the aging time of multicast member ports is 260 seconds.

  • Page 6: Display Igmp-Snooping Statistics

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands IP group(s):the following ip group(s) match to one mac group. IP group address:228.0.0.0 Static host port(s): Ethernet1/0/23 Dynamic host port(s): Ethernet1/0/10 MAC group(s): MAC group address:0100-5e00-0000...

  • Page 7: Igmp-Snooping

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands report packets, IGMP leave packets and error IGMP packets received, and the number of the IGMP group-specific query packets sent. Related command: igmp-snooping. Example # Display IGMP Snooping statistics.

  • Page 8: Igmp-Snooping Fast-Leave

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands By default, the IGMP Snooping feature is disabled. Caution: To configure IGMP Snooping in VLAN view, you should first enable IGMP Snooping globally in system view, and then enable IGMP Snooping in VLAN view. Otherwise, the IGMP Snooping function does not take effect.

  • Page 9: Igmp-Snooping General-Query Source-Ip

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands no response is received in a given period, it then removes the port from the multicast group. After this command is executed, upon receipt of an IGMP Leave packet, Switch removes the port from the multicast group directly.

  • Page 10: Igmp-Snooping Group-Limit

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands multicast switch sends. If no IP address is configured on the current VLAN interface, the default IP address 0.0.0.0. is used as the default source IP address.

  • Page 11: Igmp-Snooping Group-Policy

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands can provide up to 10 VLANs/VLAN ranges for this argument. VLAN ID ranges from 1 to 4094. Description Use the igmp-snooping group-limit command to define the maximum number of multicast groups the port can join.
  • Page 12 Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands that the users can access. With this function, you can treat different VoD users in different ways by allowing them to access the multicast streams in different multicast groups.

  • Page 13: Igmp-Snooping Host-Aging-Time

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands [H3C-vlan2] quit Configure ACL 2000 on Ethernet1/0/1 to allow this VLAN 2 port to join only the IGMP multicast groups defined in the rule of ACL 2000.

  • Page 14: Igmp-Snooping Max-Response-Time

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands The aging time of multicast member ports determines the refresh frequency of multicast group members. In an environment where multicast group members change frequently, a relatively shorter aging time is required.

  • Page 15: Igmp-Snooping Querier

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands 1.1.11 igmp-snooping querier Syntax igmp-snooping querier undo igmp-snooping querier View VLAN view Parameter None Description Use the igmp-snooping querier command to enable the IGMP Snooping querier feature on the current VLAN of the Layer 2 multicast switch.

  • Page 16: Igmp-Snooping Router-Aging-Time

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Description Use the igmp-snooping query-interval command to configure the interval for the Layer 2 multicast switch to send general query packets. Use the undo igmp-snooping query-interval command to restore the interval to the default value.

  • Page 17: Reset Igmp-Snooping Statistics

    Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands The router port here refers to the port connecting the Layer 2 switch to the router. The Layer 2 switch receives IGMP general query messages from the router through this port.
  • Page 18 Command Manual – Multicast Chapter 1 IGMP Snooping Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Parameter None Description Use the service-type multicast command to set the current VLAN as a multicast VLAN. Use the undo service-type multicast command to cancel the multicast VLAN setting.

  • Page 19: Chapter 2 Common Ip Multicast Configuration Commands

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Chapter 2 Common IP Multicast Configuration Commands 2.1 Common IP Multicast Configuration Commands 2.1.1 display mpm forwarding-table Syntax display mpm forwarding-table [ group-address ]...

  • Page 20: Display Mpm Group

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Table 2-1 Description on the fields of the display mpm forwarding-table command Field Description Total 1 entry(entries) Total number of the entries 00001 Entry number (120.0.0.2, 225.0.0.2)

  • Page 21: Display Multicast Forwarding-Table

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Example # Display the information about the multicast groups of VLAN2. <H3C> display mpm group vlan 1200 Total 1 IP Group(s). Total 1 MAC Group(s).
  • Page 22 Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Parameter group-address: Multicast group address used to specify a multicast group, in the range of 224.0.0.0 to 239.255.255.255. source-address: Unicast IP address of the multicast source.

  • Page 23: Display Multicast Routing-Table

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Field Description 122 packets that are 183,000 bytes in all Matched 122 pkts(183000 bytes), match the (s,g) entry, and 0 wrong packet Wrong If 0 pkts matches the (s,g) entry.

  • Page 24: Display Multicast-Source-Deny

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Uptime: 00:15:16, Timeout in 272 sec Upstream interface: Vlan-interface1(4.4.4.6) Downstream interface list: Vlan-interface2(2.2.2.4), Protocol 0x1: IGMP (4.4.4.4, 224.2.254.84) Uptime: 00:15:16, Timeout in 272 sec Upstream interface: Vlan-interface1(4.4.4.6)

  • Page 25: Multicast Route-Limit

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands View Any view Parameter interface-type: Port type. interface-number: Port number. Description Use the display multicast-source-deny command to display the configuration information about the multicast source port check.

  • Page 26: Multicast Routing-Enable

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Use the undo multicast route-limit command to restore the default limit on the capacity of the multicast routing table. The limit on the capacity of the multicast routing table is 256 by default.

  • Page 27: Multicast-Source-Deny

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands 2.1.8 multicast-source-deny Syntax multicast-source-deny [ interface interface-list ] undo multicast-source-deny [ interface interface-list ] View System view, Ethernet port view Parameter interface-list: List of Ethernet ports, expressed in the form of interface-list = { interface-number [ to interface-number ] } &...

  • Page 28: Reset Multicast Forwarding-Table

    H3C S3600 Series Ethernet Switches-Release 1510 Commands # Enable the multicast source port suppression feature on Ethernet1/0/1 through Ethernet1/0/10 and on Ethernet1/0/12. [H3C] multicast-source-deny interface Ethernet 1/0/1 to Ethernet 1/0/10 Ethernet 1/0/12 2.1.9 reset multicast forwarding-table Syntax reset multicast forwarding-table [ statistics ] { all | { group-address [ mask...

  • Page 29: Reset Multicast Routing-Table

    Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Example # Clear the forwarding entries whose group address is 225.5.4.3 in the MFC forwarding table. <H3C> reset multicast forwarding-table 225.5.4.3 # Clear the statistics about the forwarding entries whose group address is 225.5.4.3 in the MFC forwarding table.
  • Page 30 Command Manual – Multicast Chapter 2 Common IP Multicast Configuration H3C S3600 Series Ethernet Switches-Release 1510 Commands Example # Clear the routing entries whose group address is 225.5.4.3 from the multicast core routing table. <H3C> reset multicast routing-table 225.5.4.3 2-12...

  • Page 31: Chapter 3 Multicast Mac Address Entry Configuration Commands

    Command Manual – Multicast Chapter 3 Multicast MAC Address Entry H3C S3600 Series Ethernet Switches-Release 1510 Configuration Commands Chapter 3 Multicast MAC Address Entry Configuration Commands 3.1 Multicast MAC Address Entry Configuration Commands 3.1.1 mac-address multicast interface Syntax mac-address multicast mac-address interface interface-list vlan vlan-id...

  • Page 32: Mac-Address Multicast Vlan

    Command Manual – Multicast Chapter 3 Multicast MAC Address Entry H3C S3600 Series Ethernet Switches-Release 1510 Configuration Commands [H3C] mac-address multicast 0100-5e0a-0805 interface Ethernet 1/0/1 vlan 1 3.1.2 mac-address multicast vlan Syntax mac-address multicast mac-address vlan vlan-id undo mac-address multicast [ [ mac-address ] vlan vlan-id ]...
  • Page 33 Command Manual – Multicast Chapter 3 Multicast MAC Address Entry H3C S3600 Series Ethernet Switches-Release 1510 Configuration Commands Parameter mac-address vlan vlan-id: Displays multicast MAC address entry/entries in the specified VLAN. count: Displays the number of MAC entries. vlan-id: ID of the specific VLAN.

  • Page 34: Chapter 4 Unknown Multicast Drop Configuration Command

    Command Manual – Multicast Chapter 4 Unknown Multicast Drop H3C S3600 Series Ethernet Switches-Release 1510 Configuration Command Chapter 4 Unknown Multicast Drop Configuration Command 4.1 Unknown Multicast Drop Configuration Command 4.1.1 unknown-multicast drop enable Syntax unknown-multicast drop enable undo unknown-multicast drop enable...

  • Page 35: Chapter 5 Igmp Configuration Commands

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Chapter 5 IGMP Configuration Commands 5.1 IGMP Configuration Commands 5.1.1 display igmp group Syntax display igmp group [ group-address | interface interface-type interface-number ] View...

  • Page 36: Display Igmp Interface

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Field Description Time elapsed since multicast group was discovered Uptime (hh: mm: ss). Specifies when the member will be removed from Expires the multicast group (hh: mm: ss).

  • Page 37: Igmp Enable

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Table 5-2 Description on the fields of the display igmp interface command Field Description IGMP version IGMP version query interval Interval of general query querier timeout...

  • Page 38: Igmp Group-Limit

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands By default, IGMP is disabled on a VALN interface. . These commands do not take effect until the multicast routing feature is enabled. You need to use this command before you can configure other IGMP features.

  • Page 39: Igmp Group-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Caution: No new group can be added if the number of IGMP multicast groups has exceeded the configured limit. If the limit on the number of IGMP packets is 1, a new group takes precedence; that is, the system automatically replaces an existing multicast group with the new multicast group, and the former multicast group leaves the interface automatically.

  • Page 40: Igmp Group-Policy Vlan

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands For the meanings and value ranges of the interface-type argument and the interface-number argument, refer to the parameter descriptions in the “Port Basic Configuration” module in this manual.

  • Page 41: Igmp Host-Join Port

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands View Port view Parameter acl-number: Number of the basic IP ACL number, defining a multicast group range. The value ranges from 2,000 to 2,999. vlan-id: ID of the VLAN to which the port belongs.

  • Page 42: Igmp Host-Join Vlan

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Parameter group-address: Multicast address of the multicast group that an interface will join. port: Specifies the port in the VLAN interface. interface-list: Forward port list. You can specify multiple ports by providing this argument in the form of interface-list = { interface-type interface-number [ to { interface-type interface-number } ] }&<1-10>...

  • Page 43: Igmp Lastmember-Queryinterval

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Description Use the igmp host-join vlan command to enable an Ethernet port to join a multicast group. Use the undo igmp host-join vlan command to disable the configuration.

  • Page 44: Igmp Max-Response-Time

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands In a shared network, that is, the same network segment including multiple hosts and multicast routers, the query router (also known as querier) is responsible for maintaining the IGMP group membership on the interface.

  • Page 45: Igmp Proxy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Description Use the igmp max-response-time command to configure the maximum response time contained in the IGMP query messages. Use the undo igmp max-response-time command to restore the default value.

  • Page 46: Igmp Robust-Count

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Related command: pim neighbor-policy. Caution: The multicast route feature and the IGMP protocol must be enabled on the proxy interface. You must enable the PIM protocol on the interface before configuring the igmp proxy command on the interface.

  • Page 47: Igmp Timer Other-Querier-Present

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Use the undo igmp robust-count command to restore the default value. By default, an IGMP querier sends IGMP group-specific query packets twice. In a shared network, that is, the same network segment including multiple hosts and multicast routers, the query router is responsible for maintaining the IGMP group membership on the interface.

  • Page 48: Igmp Timer Query

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Parameter seconds: Time (in seconds) during which the IGMP querier is present, in the range of 1 to 131,070. Description Use the igmp timer other-querier-present command to configure the presence time of the IGMP querier.

  • Page 49: Igmp Version

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 5 IGMP Configuration Commands Description Use the igmp timer query command to configure the interval at which a router interface sends IGMP query messages. Use the undo igmp timer query command to restore the default value.

  • Page 50: Reset Igmp Group

    <H3C> reset igmp group interface Vlan-interface10 all # Delete the group 225.0.0.1 from Vlan-interface10. <H3C> reset igmp group interface Vlan-interface10 225.0.0.1 # Delete the IGMP groups ranging from 225.1.1.0 to 225.1.1.255 on Vlan-interface10. <H3C> reset igmp group interface Vlan-interface10 225.1.1.0 255.255.255.0 5-16...

  • Page 51: Chapter 6 Pim Configuration Commands

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Chapter 6 PIM Configuration Commands 6.1 PIM Configuration Commands 6.1.1 bsr-policy Syntax bsr-policy acl-number undo bsr-policy View PIM view Parameter acl-number: ACL number imported in BSR filtering policy, in the range of 2000 to 2999.

  • Page 52: C-Bsr

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Problems may still exist if a legal BSR is attacked, though these two measures can effectively guarantee high BSR security. The source keyword in the rule command is translated into BSR address in the bsr-policy command.

  • Page 53: C-Rp

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Related command: pim sm. Example # Configure the switch as a BSR with a priority of 2 (and the C-BSR address is designated as the IP address of VLAN-interface10).

  • Page 54: Crp-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Example # Configure the switch to advertise the BSR that the switch itself acts as the C-RP in the PIM. Basic ACL 2000 defines the groups related to the RP. The address of C-RP is designated as the IP address of VLAN-interface10.

  • Page 55: Display Pim Bsr-Info

    System View: return to User View with Ctrl+Z. [H3C] multicast routing-enable [H3C] pim [H3C-pim] crp-policy 3000 [H3C-pim] quit [H3C] acl number 3000 [H3C-acl-adv-3000] rule 0 permit source 1.1.1.1 0 destination 225.1.0.0 0.0.255.255 6.1.5 display pim bsr-info Syntax display pim bsr-info View...

  • Page 56: Display Pim Interface

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Table 6-1 Description on the fields of the display pim bsr-info command Field Description BootStrap router Priority Priority of BSR Mask Length: 30 Length of mask...

  • Page 57: Display Pim Neighbor

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands PIM DR(designated router) is 10.10.1.20 Table 6-2 Description on the fields of the display pim interface command Field Description PIM version Version of PIM PIM mode...

  • Page 58: Display Pim Routing-Table

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Table 6-3 Description on the fields of the display pim neighbor command Field Description Neighbor Address Neighbor address Interface VLAN interface on which the neighbor has been discovered...

  • Page 59: Display Pim Rp-Info

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands The displayed information about the PIM multicast routing table includes the SPT information and RPF information. Example # Display the information about the PIM multicast routing table.
  • Page 60 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands View Any view Parameter group-address: Group address to be displayed. If no multicast group is specified, the RP information about all multicast groups will be displayed.

  • Page 61: Pim

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands 6.1.10 pim Syntax undo pim View System view Parameter None Description Use the pim command to enter PIM view and configure the global PIM parameters. You cannot use the pim command to enable the PIM protocol.

  • Page 62: Pim Dm

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Use the undo pim bsr-boundary command to remove the configured PIM domain boundary. By default, no PIM domain boundary is configured on the switch. After you use this command to set a PIM domain boundary on a VLAN interface, no Bootstrap message can cross this domain boundary.

  • Page 63: Pim Neighbor-Limit

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Example # Enable the PIM-DM protocol on VLAN-interface10 of the switch. <H3C>system-view System View: return to User View with Ctrl+Z. [H3C] multicast routing-enable [H3C] interface Vlan-interface 10 [H3C-Vlan-interface10] pim dm 6.1.13 pim neighbor-limit...

  • Page 64: Pim Neighbor-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands 6.1.14 pim neighbor-policy Syntax pim neighbor-policy acl-number undo pim neighbor-policy View VLAN interface view Parameter acl-number: Basic ACL number, in the range of 2,000 to 2,999.

  • Page 65: Pim Timer Hello

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands View VLAN interface view Parameter None Description Use the pim sm command to enable the PIM-SM protocol. Use the undo pim sm command to disable the PIM-SM protocol.

  • Page 66: Register-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands When the PIM-SM protocol is enabled on a VLAN interface, the switch periodically sends Hello packets to the network devices supporting PIM to discover neighbors. If the...

  • Page 67: Reset Pim Neighbor

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands [H3C] acl number 3010 [H3C-acl-adv-3010] rule permit ip source 10.10.0.0 0.0.255.255 destination 225.1.0.0 0.0.255.255 [H3C-acl-adv-3010] quit [H3C] pim [H3C-pim] register-policy 3010 6.1.18 reset pim neighbor...
  • Page 68 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands Parameter all: Specifies all PIM neighbors. group-address: Group address. mask group-mask: Specifies a group address mask. mask-length group-mask-length: Specifies the length of group address mask.

  • Page 69: Spt-Switch-Threshold

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands 6.1.20 spt-switch-threshold Syntax spt-switch-threshold { traffic-rate | infinity } [ group-policy acl-number [ order order-value ] ] undo spt-switch-threshold [ group-policy acl-number ] View PIM view Parameter traffic-rate: Multicast traffic rate in kbps, ranging from 0 to 65,535.

  • Page 70: Source-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands <H3C>system-view System View: return to User View with Ctrl+Z. [H3C]pim [H3C-pim] spt-switch-threshold 0 6.1.21 source-policy Syntax source-policy acl-number undo source-policy View PIM view Parameter acl-number: Basic or advanced ACL, in the range of 2000 to 3999.

  • Page 71: Static-Rp

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 6 PIM Configuration Commands [H3C-acl-basic-2000] rule permit source 10.10.1.2 0 [H3C-acl-basic-2000] rule deny source 10.10.1.1 0 6.1.22 static-rp Syntax static-rp rp-address [ acl-number ] undo static-rp View PIM view Parameter rp-address: Static RP address.

  • Page 72: Chapter 7 Msdp Configuration Commands

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Chapter 7 MSDP Configuration Commands 7.1 MSDP Configuration Commands 7.1.1 cache-sa-enable Syntax cache-sa-enable undo cache-sa-enable View MSDP view Parameter None Description Use the cache-sa-enable command to enable the SA message cache mechanism.

  • Page 73: Display Msdp Peer-Status

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Parameter None Description Use the display msdp brief command to display the brief information of the MSDP peer state. Example # Display the brief information of the MSDP peer state.

  • Page 74: Display Msdp Sa-Cache

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Example # Display the detailed information of MSDP peer 10.110.11.11. <H3C> display msdp peer-status 10.110.11.11 MSDP Peer 20.20.20.20, AS 100 Description: Information about connection status:...
  • Page 75 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands source-address: Source address of the (S, G) entry. If you do not specify a source address, the system displays all source information of the specified group. If you specify neither a group address nor a source address, the system displays all SA caches.

  • Page 76: Display Msdp Sa-Count

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands 7.1.5 display msdp sa-count Syntax display msdp sa-count [ autonomous-system-number ] View Any view Parameter autonomous-system-number: AS from which a source and group come The value ranges from 1 to 65535.

  • Page 77: Import-Source

    # Configure the (S, G) entries in the multicast routing table to be advertised when an MSDP peer creates an SA message. <H3C> system-view System View: return to User View with Ctrl+Z. [H3C] acl number 3101 [H3C-acl-adv-3101] rule permit ip source 10.10.0.0 0.0.255.255 destination 225.1.0.0 0.0.255.255 [H3C-acl-adv-3101] quit [H3C] msdp [H3C-msdp] import-source acl 3101 7.1.7 msdp...

  • Page 78: Msdp-Tracert

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands View System view Parameter None Description Use the msdp command to enable MSDP and enter MSDP view. Use the undo msdp command to clear all configurations in MSDP view, release resources occupied by MSDP, and restore the initial state.
  • Page 79 <H3C> msdp-tracert 10.10.1.1 225.2.2.2 20.20.20.20 # Specify the maximum number of hops to be traced and collect the detailed SA and MSDP peer information. <H3C> msdp-tracert 10.10.1.1 225.2.2.2 20.20.20.20 max-hops 10 sa-info peer-info MSDP tracert: press CTRL_C to break D-bit:...

  • Page 80: Mtracert

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Field Description Up time of the (S, G, RP) entry in SA cache of Cache Entry Uptime the local router, in minutes. The maximum value is 255.

  • Page 81: Originating-Rp

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands last-hop-router-address: IP address of the last-hop router. Description Use the mtracert command to trace the transmission path of the packet sent by the multicast source over the network.

  • Page 82: Peer Description

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands 7.1.11 peer description Syntax peer peer-address description text undo peer peer-address description View MSDP view Parameter peer-address: IP address of the MSDP peer. text: Description text, case-sensitive. The maximum length is 80 characters.

  • Page 83: Peer Minimum-Ttl

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Description Use the peer mesh-group command to add an MSDP peer to a mesh group. Use the undo peer mesh-group command to cancel the configuration.

  • Page 84: Peer Request-Sa-Enable

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands [H3C-msdp] peer 110.10.10.1 minimum-ttl 10 7.1.14 peer request-sa-enable Syntax peer peer-address request-sa-enable undo peer peer-address request-sa-enable View MSDP view Parameter peer-address: IP address of the MSDP peer.

  • Page 85: Peer Connect-Interface

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands sa-limit: Maximum number of SA messages cached, ranging from 1 to 2,048. Description Use the peer sa-cache-maximum command to set the maximum number of SA messages cached on the router.

  • Page 86: Peer Sa-Policy

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands If the MSDP peer of the local router is also a BGP peer, the MSDP peer and the BGP peer must use the same IP addresses.

  • Page 87: Peer Sa-Request-Policy

    H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands System View: return to User View with Ctrl+Z. [H3C] acl number 3100 [H3C-acl-adv-3100] rule permit ip source 170.15.0.0 0.0.255.255 destination 225.1.0.0 0.0.255.255 [H3C-acl-adv-3100] quit [H3C] msdp [H3C-msdp] peer 125.10.7.6 connect-interface Vlan-interface 100 [H3C-msdp] peer 125.10.7.6 sa-policy export acl 3100...

  • Page 88: Reset Msdp Peer

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands [H3C-acl-basic-2001] rule permit source 225.1.1.0 0.0.0.255 [H3C-acl-basic-2001] quit [H3C] msdp [H3C-msdp] peer 175.58.6.5 sa-request-policy acl 2001 7.1.19 reset msdp peer Syntax reset msdp peer peer-address...

  • Page 89: Reset Msdp Statistics

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Related command: cache-sa-enable, display msdp sa-cache. Example # Clear the cached entries whose group address is 225.5.4.3 from the SA cache. <H3C> reset msdp sa-cache 225.5.4.3 7.1.21 reset msdp statistics...

  • Page 90: Static-Rpf-Peer

    Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands Use the undo shutdown command to remove the configuration. By default, no MSDP peer is shut down. Related command: peer. Example # Shut down the MSDP peer 125.10.7.6.

  • Page 91: Timer Retry

    # Configure a static RPF peer. <H3C> system-view System View: return to User View with Ctrl+Z. [H3C] ip ip-prefix list1 permit 130.10.0.0 16 greater-equal 16 less-equal 32 [H3C] msdp [H3C-msdp] peer 130.10.7.6 connect-interface Vlan-interface 100 [H3C-msdp] static-rpf-peer 130.10.7.6 rp-policy list1 7.1.24 timer retry...
  • Page 92 Command Manual – Multicast H3C S3600 Series Ethernet Switches-Release 1510 Chapter 7 MSDP Configuration Commands [H3C-msdp] timer retry 60 7-21...

Table of Contents