H3C S3600 Series Operation Manual

H3C S3600 Series Operation Manual

System maintenance and debugging
Hide thumbs Also See for S3600 Series:

Advertisement

Operation Manual - System Maintenance and Debugging
H3C S3600 Series Ethernet Switches-Release 1510
Chapter 1 BootROM and Host Software Loading ...................................................................... 1-1
1.1 Introduction to Loading Approaches .................................................................................. 1-1
1.2 Local BootROM and Software Loading ............................................................................. 1-1
1.2.1 BOOT Menu ............................................................................................................ 1-2
1.2.2 Loading by XModem through Console Port ............................................................ 1-3
1.2.3 Loading by TFTP through Ethernet Port ................................................................. 1-8
1.2.4 Loading by FTP through Ethernet Port ................................................................. 1-10
1.3 Remote BootROM and Software Loading ....................................................................... 1-12
1.3.1 Remote Loading Using FTP.................................................................................. 1-12
1.3.2 Remote Loading Using TFTP................................................................................ 1-18
Chapter 2 Basic System Configuration & Debugging ............................................................... 2-1
2.1 Basic System Configuration............................................................................................... 2-1
2.1.1 Basic System Configuration Tasks ......................................................................... 2-1
2.1.2 Entering System View from User View ................................................................... 2-1
2.1.3 Setting the System Name of the Switch.................................................................. 2-2
2.1.4 Setting the Date and Time of the System ............................................................... 2-2
2.1.5 Setting the Local Time Zone ................................................................................... 2-2
2.1.6 Setting the Summer Time ....................................................................................... 2-2
2.1.7 Setting the CLI Language Mode ............................................................................. 2-3
2.1.8 Returning from Current View to Lower Level View ................................................. 2-3
2.1.9 Returning from Current View to User View ............................................................. 2-3
2.2 Displaying the System Status ............................................................................................ 2-3
2.3 Debugging the System ...................................................................................................... 2-4
2.3.1 Enabling/Disabling System Debugging................................................................... 2-4
2.3.2 Displaying Debugging Status .................................................................................. 2-6
Chapter 3 Network Connectivity Test.......................................................................................... 3-1
3.1 Network Connectivity Test ................................................................................................. 3-1
3.1.1 ping.......................................................................................................................... 3-1
3.1.2 tracert ...................................................................................................................... 3-1
Chapter 4 Device Management .................................................................................................... 4-1
4.1 Introduction to Device Management .................................................................................. 4-1
4.2 Device Management Configuration ................................................................................... 4-1
4.2.1 Device Management Configuration Tasks .............................................................. 4-1
4.2.2 Rebooting the Ethernet Switch................................................................................ 4-1
4.2.3 Scheduling a Reboot on the Switch ........................................................................ 4-2
4.2.4 Specifying the APP to be Adopted at Reboot ......................................................... 4-2

Table of Contents

i
Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S3600 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for H3C S3600 Series

  • Page 1: Table Of Contents

    Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Table of Contents Table of Contents Chapter 1 BootROM and Host Software Loading ..............1-1 1.1 Introduction to Loading Approaches .................. 1-1 1.2 Local BootROM and Software Loading ................1-1 1.2.1 BOOT Menu ......................
  • Page 2 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Table of Contents 4.2.5 Upgrading the BootROM..................4-3 4.2.6 Upgrading the Host Software in the Fabric ............. 4-3 4.3 Displaying the Device Management Configuration............4-3 4.4 Remote Switch Upgrade Configuration Example .............. 4-4...
  • Page 3: Chapter 1 Bootrom And Host Software Loading

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Chapter 1 BootROM and Host Software Loading Traditionally, switch software is loaded through a serial port. This approach is slow, time-consuming and cannot be used for remote loading.
  • Page 4: Boot Menu

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Note: The loading process of the BootROM software is the same as that of the host software, except that during the former process, you should press <Ctrl+U> and <Enter> after entering the BOOT menu and the system gives different prompts.
  • Page 5: Loading By Xmodem Through Console Port

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Enter the correct BootROM password (no password is need by default). The system enters the BOOT Menu: BOOT MENU 1. Download application file to flash 2.
  • Page 6 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading 3. Set XMODEM protocol parameter 0. Return to boot menu Enter your choice(0-3): Step 2: Press 3 in the above menu to download the BootROM using XModem. The...
  • Page 7 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Figure 1-1 Properties dialog box Figure 1-2 Console port configuration dialog box Step 5: Click the <Disconnect> button to disconnect the HyperTerminal from the switch and then click the <Connect>...
  • Page 8 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Figure 1-3 Connect and disconnect buttons Note: The new baudrate takes effect after you disconnect and reconnect the HyperTerminal program.
  • Page 9 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Figure 1-5 Sending file page Step 9: After the sending process completes, the system displays the following information: Loading ...CCCCCCCCCC done! Step 10: Reset HyperTerminal’s baudrate to 9600 bps (refer to Step 4 and 5).
  • Page 10: Loading By Tftp Through Ethernet Port

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading 3. Set XMODEM protocol parameter 0. Return to boot menu Enter your choice(0-3): Step 2: Enter 3 in the above menu to load the host software by using XModem.
  • Page 11 Step2: Run the TFTP server program on the TFTP server, and specify the path of the program to be downloaded. Caution: TFTP server program is not provided with the H3C Series Ethernet Switches. Step 3: Run the HyperTerminal program on the configuration PC. Start the switch. Then enter the BOOT Menu.
  • Page 12: Loading By Ftp Through Ethernet Port

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Step 1: Select <1> in BOOT Menu and press <Enter>. The system displays the following information: 1. Set TFTP protocol parameter 2.
  • Page 13 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Note: You can use one computer as both configuration device and FTP server. Step 2: Run the FTP server program on the FTP server, configure an FTP user name and password, and copy the program file to the specified FTP directory.
  • Page 14: Remote Bootrom And Software Loading

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Enter your choice(0-3): Enter 2 in the above menu to download the host software using FTP. The subsequent steps are the same as those for loading the BootROM, except for that the system gives the prompt for host software loading instead of BootROM loading.
  • Page 15 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading <H3C> ftp 10.1.1.1 Trying ... Press CTRL+K to abort Connected. 220 WFTPD 2.0 service (by Texas Imperial Software) ready for new user...
  • Page 16 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading If the space of the Flash memory is not enough, you can delete the unused files in the Flash memory before software downloading.
  • Page 17 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading [H3C] local-user test New local user added. [H3C-luser-test] password simple pass [H3C-luser-test] service-type ftp Step 4: Enable FTP client software on the PC. Refer to Figure 1-10 for the command line interface in Windows operating system.
  • Page 18 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Figure 1-11 Enter BootROM directory Step 6: Enter ftp 192.168.0.39 and enter the user name test, password pass, as shown in Figure 1-12, to log on to the FTP server.
  • Page 19 Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading Figure 1-13 Upload file S3600.btm to the switch Step 8: Configure S3600.btm to be the BootROM at next startup, and then restart the switch.
  • Page 20: Remote Loading Using Tftp

    Operation Manual – System Maintenance and Debugging Chapter 1 BootROM and Host Software H3C S3600 Series Ethernet Switches-Release 1510 Loading 1.3.2 Remote Loading Using TFTP The remote loading using TFTP is similar to that using FTP. The only difference is that TFTP is used to load software to the switch, and the switch can only act as a TFTP client.
  • Page 21: Basic System Configuration

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging Chapter 2 Basic System Configuration & Debugging 2.1 Basic System Configuration 2.1.1 Basic System Configuration Tasks Table 2-1 Basic system configuration tasks...
  • Page 22: Setting The System Name Of The Switch

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging 2.1.3 Setting the System Name of the Switch Table 2-3 Set the system name of the switch Operation Command Description...
  • Page 23: Setting The Cli Language Mode

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging Table 2-6 Set the summer time Operation Command Description Set the name and time clock summer-time zone_name range of the summer...
  • Page 24: Debugging The System

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging Table 2-10 System information display commands Operation Command Description Display the current date display clock and time of the system...
  • Page 25 Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging Debugging information Debugging information Debugging information Debugging information Protocol debugging setting Protocol debugging setting Terminal display setting Terminal display setting Figure 2-1 Debugging information outpu You can use the following commands to perform the settings.
  • Page 26: Displaying Debugging Status

    Operation Manual – System Maintenance and Debugging Chapter 2 Basic System Configuration H3C S3600 Series Ethernet Switches-Release 1510 & Debugging 2.3.2 Displaying Debugging Status Table 2-12 Display the current debugging status in the system Operation Command Description display debugging { fabric |...
  • Page 27: Chapter 3 Network Connectivity Test

    Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 3 Network Connectivity Test Chapter 3 Network Connectivity Test 3.1 Network Connectivity Test 3.1.1 ping You can use the ping command to check the network connectivity and the reachability of a host.
  • Page 28 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 3 Network Connectivity Test Table 3-2 The tracert command Operation Command Description Trace the gateways that a tracert [ -a source-ip ] [ -f execute packet passes from the...
  • Page 29: Chapter 4 Device Management

    Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management Chapter 4 Device Management 4.1 Introduction to Device Management The device management function of the Ethernet switch enables the display of current status and event-debugging information of the system. Through this function, you can maintain and manage the status and communication of the physical devices, and restart the system when some functions of the system are exceptional.
  • Page 30: Scheduling A Reboot On The Switch

    Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management Table 4-2 Reboot the Ethernet switch Operation Command Description Reboot the Ethernet switch reboot [ unit unit-id ] — 4.2.3 Scheduling a Reboot on the Switch After you schedule a reboot on the switch, the switch will reboot at the specified time.
  • Page 31 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management 4.2.5 Upgrading the BootROM You can use the BootROM program saved in the Flash memory of the switch to upgrade the running BootROM. With this command, a remote user can conveniently upgrade the BootRom by uploading the BootROM to the switch through FTP and running this command.
  • Page 32 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management Table 4-7 Display the operating status of the device management Operation Command Description Display the APP to be display boot-loader unit adopted at next startup...
  • Page 33 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management Make configuration so that the IP address of a VLAN interface on the switch is 1.1.1.1, the IP address of the PC is 2.2.2.2, and the switch and the PC is reachable to each other.
  • Page 34 Operation Manual – System Maintenance and Debugging H3C S3600 Series Ethernet Switches-Release 1510 Chapter 4 Device Management <H3C> ftp 2.2.2.2 Trying ... Press CTRL+K to abort Connected. 220 WFTPD 2.0 service (by Texas Imperial Software) ready for new user User(none):switch...

Table of Contents