NEC MultiSync UN462A User Manual page 125

CONTROL MENU
CEC
CEC
AUTO TURN OFF
AUDIO RECEIVER
SEARCH DEVICE
RESET
OPTION
OPTION MENU
OPTION POWER
AUDIO
*1
INTERNAL PC
*1
OFF WARNING
AUTO OFF
START UP PC
FORCE QUIT
SLOT2 CH SETTING
AUTO
1CH
2CH
* 1 : This function depends on which Option Board installed in the monitor. When changing the setting, turn the monitor's main power switch off and on again.
This function enables you to control the HDMI CEC compliant device connected via HDMI connector. Please
connect a device to the HDMI2 (CEC) port.
(CEC is an abbreviation of Consumer Electronics Control).
When [ON] is set, the connected HDMI CEC devices are controlled by the wireless remote control (option).
Please set items below.
NOTE: If [ON] is selected, the below functions are activated.
When the connected HDMI CEC device plays, the monitor synchronously turns on then changes the input
signal to HDMI. If the monitor has been turned on, when a connected HDMI CEC device plays, input signal
switches to HDMI.
Depending on the connected device, the device may not work properly.
When the monitor goes to standby via remote control or the
device goes to standby synchronously.
NOTE: If the connected HDMI CEC device is recording, the device does not go into standby.
Activates HDMI CEC audio amplifier. If YES is set, outputs the sounds of the connected HDMI CEC device
from the connected HDMI CEC audio amplifier. If [NO] is set, the HDMI CEC audio amplifier connected to the
monitor is set to mute.
NOTE: When an HDMI CEC audio amplifier is connected, set to [YES].
Please set to [NO] if there is no connected HDMI CEC audio device to the monitor.
Searches the HDMI CEC device connected to the monitor. When search is successful, the connected HDMI
CEC device's type and registered device name are shown. When search has been completed or failed, the
[SEARCH DEVICE] is set to [NO] automatically. To retry the [SEARCH DEVICE], set it to [YES] again. After
detecting HDMI CEC devices, you can switch the device input by selecting the device.
Resets all the settings within the CONTROL menu back to factory setting except for [LAN],
[CHANGE PASSWORD], [SECURITY] and [PING].
Allows the monitor to supply power to an Option Board slot during power save mode or standby mode.
[AUTO]: Power supply depends on an Option Board is connected or not.
[ON]: Supply power to the connected option continues during power save mode or standby mode.
[OFF]: Supply power to the connected option stops during power save mode or standby mode.
NOTE: To activate Power management function with no signal input from the inserted slot 2 type option, please
set [OPTION POWER] to [AUTO] or [ON].
Selects the sound input signal according to the slot2 type option specifications. To activate [DIGITAL], select
[OPTION] for input signal and [OPTION] for [AUDIO INPUT].
NOTE: [DIGITAL] is activated only when [OPTION] is selected for input signal and [OPTION] for [AUDIO
INPUT].
The function is available for a slot 2 type PC.
(Not adjustable)
Monitor power is automatically [OFF] when the internal PC is [OFF] or the monitor is in power save mode.
NOTE: If you select [OFF], the monitor power is not automatically [ON] when the internal PC is [ON].
When [ON] is selected, the internal PC will start.
When [ON] is selected, a forced shutdown of the internal PC will be carried out.
Please use this function only when the operating system cannot be shut down manually.
Selects signal type according to the slot 2 type option specifications.
Sets the signal type automatically.
Fills the screen entirely with the signal which is selected in [SLOT2 CH SELECT].
The DisplayPort signal is displayed on the left half of the screen, the TMDS signal is displayed on the right
half. If the internal PC does not support either one of the signal types, the existing signal will automatically be
displayed on the full screen.
button on the monitor, a connected HDMI CEC
English−121