Advertisement
Quick Links
QIG-TMX4P-492SVS
UN492S-TMX4P, UN492VS-TMX4P
Parts List
o (4) UN492S , UN492VS Displays
o (4) Onsite Service Warranties (ONSITEMN-3Y-17)
o (4) Peerless Pullout Wall Mounts (DS-VW775)
o (1) Peerless Wall Mount Spacer (DS-VWRS091)
o (1) 25ft Cat5e Patch Cable
o (1) IR/Remote Control Kit (KT-RC3)
o (2) Overframe Bezel Kits (KT-49UN-OF)
o (1) SurgeX 4-Port Power Conditioner
o (1) Display Wall Calibrator Kit (KT-LFD-CC2)
NOTES:
o
Any walls that this video wall solution is anchored to must be strong enough to support the displays and the
installation must be in accordance with any local building codes. All mounting apparatuses must make secure
contact to wooden studs.
o
Please read entire document before starting installation
NEC Display Solutions of America, Inc.
Rev 1.1
Advertisement
Related Manuals for NEC UN492S-TMX4P
Summary of Contents for NEC UN492S-TMX4P
- Page 1 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 Parts List o (4) UN492S , UN492VS Displays o (4) Onsite Service Warranties (ONSITEMN-3Y-17) o (4) Peerless Pullout Wall Mounts (DS-VW775) o (1) Peerless Wall Mount Spacer (DS-VWRS091) o (1) 25ft Cat5e Patch Cable...
- Page 2 Connect the NEC display using the provided HDMI cables. Please note that in the picture below, the IN connection is on the right side of the display and circled in red while the OUT connection is located on the bottom of the display and circled in blue.
- Page 3 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 Apply the OverFrame bezel kit to the video wall. Please follow instructions provided with kit. KT-49UN-OF is utilized with the UN492S/VS displays and KT-46UN-OF3 Overframe Kit Screw the IR Receiver (KT-RC3) directly to the outside of the video wall and plug it directly into the IR In terminal of Display 1 as shown below.
- Page 4 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 Note that LAN power is OFF out of the box so this will need to be changed for each display within the wall. Go into the Multi-DSP menu of the display 1 which will be where you first started the LAN daisy chain and enable the AUTO ID within the ID Control setting.
- Page 5 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 addresses if no DNS is detected and the IP Setting within the IP Address Setting in the External Control menu is set to AUTO. Note that this is the setting out of the box.
- Page 6 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 Ensure that video source is connected to the DisplayPort1 (Daisy Chain In) or the HDMI1 (Daisy Chain In) interface of display 1. Note that the DisplayPort (Daisy Chain Out) on each...
- Page 7 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 fills the entirety of the wall. Activating Auto Tile Matrix changes the Tile Matrix, Tile Matrix Mem, Input Signal, Video Out Setting and DisplayPort in the Terminal Settings menu.
- Page 8 NEC Display Solutions of America, Inc. QIG-TMX4P-492SVS UN492S-TMX4P, UN492VS-TMX4P Rev 1.1 If you are experiencing issues with this setup, please call our Technical Support number at (800) 632-4662...