Parameter List (By Function Group); Operation Command And Frequency Command; Protective Function Parameter; Monitor Display And Monitor Output Signal - Mitsubishi Electric A800-E Instruction Manual

Parameter list (by function group)

2.2
Parameter list (by function group)
D: Operation command and
frequency command
Parameters that specify the inverter's command source, and
parameters that set the motor driving frequency and torque.
Pr.
Pr.
group
NET mode operation command
D012 550
source selection
PU mode operation command
D013 551
source selection
D400 804 Torque command source selection
 

The setting is available for the FR-A800-E only.
H: Protective function parameter
Parameters to protect the motor and the inverter.
Pr.
Pr.
group
H700 810 Torque limit input method selection
 

The setting is available for the FR-A800-E only.
M: Monitor display and monitor
output signal
Parameters regarding the inverter's operating status. These
parameters are used to set the monitors and output signals.
Pr.
Pr.
group
M400 190 RUN terminal function selection
M401 191 SU terminal function selection
M402 192 IPF terminal function selection
M403 193 OL terminal function selection
M404 194 FU terminal function selection
M405 195 ABC1 terminal function selection
M406 196 ABC2 terminal function selection
M410 313 DO0 output selection
M411 314 DO1 output selection
M412 315 DO2 output selection
N: Operation via communication
and its settings
Parameters for communication operation. These parameters
set the communication specifications and operation.
Pr.
Pr.
group
Communication EEPROM write
N001 342
selection
N010 349 Communication reset selection
Stop mode selection at
N013 502
communication error
Operation frequency during
N014 779
communication error
N100 541 Frequency command sign selection
8
PARAMETER
Refer
Name to
page
9
9
51
Refer
Name to
page
51
Refer
Name to
page
13
13
13
13
13
13
13
13
13
13
Refer
Name to
page
14
14
14
14
51
Pr.
Pr.
group
N103 544 CC-Link extended setting
N600 1434 Ethernet IP address 1
N601 1435 Ethernet IP address 2
N602 1436 Ethernet IP address 3
N603 1437 Ethernet IP address 4
N610 1438 Subnet mask 1
N611 1439 Subnet mask 2
N612 1440 Subnet mask 3
N613 1441 Subnet mask 4
N630 1427 Ethernet function selection 1
N631 1428 Ethernet function selection 2
N632 1429 Ethernet function selection 3
Link speed and duplex mode
N641 1426
selection
N642 1455 Keepalive time
Ethernet signal loss detection
N643 1431
function selection
Ethernet communication check time
N644 1432
interval
Ethernet communication network
N650 1424
number
Ethernet communication station
N651 1425
number
N660 1442 Ethernet IP filter address 1
N661 1443 Ethernet IP filter address 2
N662 1444 Ethernet IP filter address 3
N663 1445 Ethernet IP filter address 4
Ethernet IP filter address 2 range
N664 1446
specification
Ethernet IP filter address 3 range
N665 1447
specification
Ethernet IP filter address 4 range
N666 1448
specification
Ethernet command source selection
N670 1449
IP address 1
Ethernet command source selection
N671 1450
IP address 2
Ethernet command source selection
N672 1451
IP address 3
Ethernet command source selection
N673 1452
IP address 4
Ethernet command source selection
N674 1453
IP address 3 range specification
Ethernet command source selection
N675 1454
IP address 4 range specification
Station number in inverter-to-
N681 1124
inverter link
Number of inverters in inverter-to-
N682 1125
inverter link system
Refer
Name to
page
51
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
72
72