Specifications (82410) - Kubota B2410 Workshop Manual

SPECIFICATIONS
B2410· B2710· B2910 WSM, 12271
SPECIFICATIONS (82410)
Note: Manufacture s estimate the company reserves the right to change the specifications Without notice.
Model
B2410HSDB
T
B2410HSD
I
B2410HSE
PTa power
13.4 kW (18.0 HP)
Maker
KUBOTA
Model D1105-E-D16
Type
Indirect Injection. Vertical, water-cooled, 4-cycle diesel
Number of cylinders 3
Bore and stroke 78 x 78.4 mm(3.07 x 3.09 in.)
Total displacement
1123 cm
3
(68.5 cu.in.)
Engine
Engine net power (DIN)
17.9 kW (24.0 HP)
Rated revolution (min-
1 )
43.3 r/s (2600 rpm)
Maximum torque
67 N·m (50 ft-Ibs)
Battery
12 V, RC: 79 min, CCA: 433 A
Starting system
Electric starting with cell starter 12 V, 1.0 kW
Lubricating system Forced lubrication by trochoidal pump
Cooling system Pressurized radiator, .forced circulation with water pump
Fuel
Diesel fuel No. 2-D [above
~1
0 'C (14'F)], Diesel fuel NO.1 [below -1 O'C (14 'F)]
Fuel tank 24 L. (6.3 U.S.gals, 5.3
Imp~gal)
Engine crankcase (with filter) 3.0 L (3.2 U.S.qts, 2.6 Imp.qts)
Capacities
Engine coolant
3.8 L(4.0 U.S.qts, 3.3 Imp.qts)
Transmission case 12.5L (3.30 U.S.gals, 2.75 Imp.gals)
4.5 L < I >
> •.
\3.1 L I
Front axle case
(4.8 U.S.qts, 4.0 Imp.qts) .....(3.9U.S.qts, 3.3 Imp.qts)
Overall length (without 3P) 2330 rnm (91.7 in.)
Overall width 1175 mm (46.3 in.)
Overall height (with RaPS)
1965 mm (77.4 in.)
Dimensions
Overall height (top of steering wheel) 1372 mm (54.0 in.)
Wheel base 1500 mm (59.0 in.)
Minimum ground clearance 285 mm (11.2 in.)
I
325 mm (12.8 in.)
Front
835 mm (32.9 in.)
I
900 mm (35.4 in.)
Tread
Rear 890 to 1064 mm (35.0 to 41.9 in.)
Weight (with RaPS) 680 kg (1500 Ibs)
T
670 kg (1477Ibs)
I
620 kg (1367Ibs)
Clutch
Dry single plate
Front 7-12
I
6.5-10
Tires
Rear 11.2-16
Steering
Integral type power steering
Travelling
Transmission
Main-hydrostatic transmission, High-Low gear shift (2 forward and 2reverse)
system
Brake
Wet disk type
Min. turning radius (with brake)
2.1 m (6.9 feet)
I
2.0 m (6.6 feet)
Differential Bevel gear
Hydraulic control system Position Control
Pump capacity 3P: 16.6 L (4.4 U.S.GPM, 3.7 Imp.GPM), PS: 9.8 L (2.6 U.S.GPM, 2.2 Imp.GPM)
Hydraulic Three point hitch
SAE Category
I
system
At lift points 750 kg (1655 Ibs)
Max. lift force
(24 in, behind lift
points)
590 kg (1300 Ibs)
PTa shaft SAE 1-3/8, 6 splines
Rear
Revolution 1 speed (540 min-
1
(rpm) at 2584 engine min-
1
(rpm))
PTa system
PTa shaft USA No.5 (KUBOTA 10-tooth) involute spline
Mid.
Revolution
1 speed (2537 min-
1
(rpm) at 2600 engine min-
1
(rpm))
*
,
..
12271200050
7