Communication Commands - YOKOGAWA DL7480 User Manual

3.8

Communication Commands

Command
SPI Analyzer Group
:SEARch:SPI?
:SEARch:SPI:ANALyze?
:SEARch:SPI:ANALyze:ABORt
:SEARch:SPI:ANALyze:EXECute
:SEARch:SPI:ANALyze:SETup?
:SEARch:SPI:ANALyze:SETup:BITorder Sets the bit order of analysis* data or queries the current setting.
:SEARch:SPI:ANALyze:SETup:CLOCk?
:SEARch:SPI:ANALyze:SETup:CLOCk:HYSTeresis
:SEARch:SPI:ANALyze:SETup:CLOCk:LEVel
:SEARch:SPI:ANALyze:SETup:CLOCk:POLarity
:SEARch:SPI:ANALyze:SETup:CS?
:SEARch:SPI:ANALyze:SETup:CS:CHANnel<x>?
:SEARch:SPI:ANALyze:SETup:CS:CHANnel<x>:LEVel
:SEARch:SPI:ANALyze:SETup:CS:CHANnel<x>:MODE
:SEARch:SPI:ANALyze:SETup:CS:LOGic? Queries all settings related to the logic input of the chip select signal (CS)
:SEARch:SPI:ANALyze:SETup:CS:LOGic:{A0|A1|A2|A3|A4|A5|A6|A7}
:SEARch:SPI:ANALyze:SETup:CS:ESTate Sets the enable status of the chip select signal (CS) in the analysis* or
:SEARch:SPI:ANALyze:SETup:DATA<x>? Queries all settings related to the data input/output signal (Data1/Data2)
:SEARch:SPI:ANALyze:SETup:DATA<x>:LEVel
:SEARch:SPI:ANALyze:SETup:DATA<x>:MODE
:SEARch:SPI:ANALyze:SETup:MPOSition Sets the reference point when the reference point of the analysis* is set to 3-47
:SEARch:SPI:ANALyze:SETup:RPOint
:SEARch:SPI:LIST?
:SEARch:SPI:SEARch?
3-40
This section contains only the communication commands related to the SPI Bus signal
analysis function. For a description of other DL7440/DL7480 communication commands,
see the DL7440/DL7480 Communication Interface User's Manual (IM701450-17E) .
Function
Queries all settings related to the analysis* function.
Queries all settings related to the execution of the analysis.*
Aborts the execution of the Analysis.*
Executes the analysis.*
Queries all settings related to the analysis* conditions.
Queries all settings related the clock signal in the analysis.*
Sets the hysteresis for the detection level of the clock signal in the analysis* 3-45
or queries the current setting.
Sets the detection level of the clock signal in the analysis* or queries the
current setting.
Sets the slope of the clock signal in the analysis* or queries the current
setting.
Queries all settings related the chip select signal (CS) in the analysis.*
Queries all settings related to each channel of the chip select signal (CS)
in the analysis.*
Sets the level of each channel of the chip select signal (CS) in the analysis* 3-46
or queries the current setting.
Sets whether to handle the channel as a chip select signal (ON/OFF) in the 3-46
analysis* or queries the current setting.
in the analysis.*
Sets whether to handle each bit of the logic input as a chip select signal
(ON/OFF) in the analysis* or queries the current setting.
queries the current setting.
in the analysis.*
Sets the threshold level of the data input/output signal (Data1/Data2) in the 3-47
analysis* or queries the current setting.
Enables/Disables the data input/output signal (Data1/Data2) in the analysis*3-47
or queries the current setting.
manual or queries the current setting.
Sets whether to set the reference point of the analysis* to the trigger
position or set it manually or queries the current setting.
Outputs one byte of analysis* result as a character string.
Queries all settings related to the analysis* result search.
Page
3-44
3-44
3-45
3-45
3-45
3-45
3-45
3-45
3-45
3-46
3-46
3-46
3-46
3-47
3-47
3-47
3-47
3-48
IM 701450-51E