Yes, the YOKOGAWA DLM2000 Series can automatically save waveforms to a USB flash drive with updated file names. It supports auto-naming features, including numbering (adding a three-digit number from 000 to 999) and date-based naming, ensuring unique file names.

This answer is automatically generated

Summary of Contents for YOKOGAWA DLM2000 Series

Page 1: Communication Interface
DLM2000 Series Digital Oscilloscope Mixed Signal Oscilloscope Communication Interface IM 710105-17E 10th Edition...
Page 2: List Of Manuals
YOKOGAWA is strictly prohibited. • The TCP/IP software of this product and the documents concerning it have been developed/ created by YOKOGAWA based on the BSD Networking Software, Release 1 that has been licensed from the Regents of the University of California.
Page 3 • To use the USB communication features, your PC must have the following: • DLM Series Library (TMCTL) • USB device driver for connecting the DLM2000 series to the PC • To use the Ethernet communication features, your PC must have the following: •...
Page 4: How To Use This Manual
How to Use This Manual Structure of the Manual This manual contains six chapters and an appendix. Chapter 1 USB Interface Describes the features and specifications of the USB interface. Chapter 2 Ethernet Interface (Optional) Describes the features and specifications of the Ethernet interface. Chapter 3 GP-IB Interface (Optional) Describes the features and specifications of the GP-IB interface.
Page 5: Conventions Used In This Manual
How to Use This Manual Conventions Used in This Manual Notes and Cautions The notes and cautions in this manual are categorized using the following symbols. WARNING Calls attention to actions or conditions that could cause serious or fatal injury to the user, and precautions that can be taken to prevent such occurrences.
Page 6: Table Of Contents
Contents List of Manuals ...........................i How to Use This Manual ........................iii Chapter 1 USB Interface Component Names and Functions ................... 1-1 1.2 USB Interface Features and Specifications ..............1-2 USB Interface Connection ....................1-4 1.4 Configuring the DLM2000 USB Settings ................1-5 Chapter 2 Ethernet Interface (Optional) Component Names and Functions ...................
Page 7 Contents 5.19 MATH Group......................... 5-123 5.20 MEASure Group ......................5-128 5.21 RECall Group ....................... 5-144 5.22 REFerence Group ......................5-145 5.23 SEARch Group ......................5-146 5.24 SERialbus Group ......................5-152 5.25 SNAP Group ......................... 5-223 5.26 SSTart Group ........................ 5-224 5.27 STARt Group ........................
Page 8: Chapter 1 Usb Interface
Chapter 1 USB Interface Component Names and Functions Front Panel UTILITY key Press this key to select the USB interface. DLM2054 2.5GS/s 500MHz MIXED SIGNAL OSCILLOSCOPE PRINT MENU FILE UTILITY CLEAR CLEAR TRACE key (SHIFT+CLEAR TRACE) TRACE Press this key to switch from Remote mode to SNAP SHOT Local mode, which allows you to control the...
Page 9: Usb Interface Features And Specifications
USB Interface Features and Specifications USB Interface Features Reception Features Allow you to specify the same settings that you can using the front panel keys. Receive output requests for measured and computed data, panel setting data, and error codes. Transmission Features The DLM2000 can (1) transmit measured and computed data, (2) transmit panel setting data and the status byte, and (3) error codes when errors occur.
Page 10 1.2 USB Interface Features and Specifications Switching between Remote and Local Modes Switching from Local to Remote Mode The DLM2000 switches to Remote mode when it is in Local mode and it receives a :COMMunicate:REMote ON command from the PC. •...
Page 11: Usb Interface Connection
USB Interface Connection Notes about Connections • Be sure to insert the USB cable connector firmly into the USB port. • If you are connecting multiple devices by using a USB hub, connect the DLM2000 to the USB hub port that is closest to the port that the controller is connected to. •...
Page 12: Configuring The Dlm2000 Usb Settings
• Install the YOKOGAWA USB TMC (Test and Measurement Class) driver on your PC. For information about how to obtain the YOKOGAWA USB TMC driver, contact your nearest YOKOGAWA dealer. You can Index also access the YOKOGAWA USB driver download webpage and download the driver.
Page 13: Chapter 2 Ethernet Interface (Optional)
Chapter 2 Ethernet Interface (Optional) Component Names and Functions Front Panel UTILITY key Press this key to select the Ethernet interface. DLM2054 2.5GS/s 500MHz MIXED SIGNAL OSCILLOSCOPE PRINT MENU FILE UTILITY CLEAR CLEAR TRACE key (SHIFT+CLEAR TRACE) TRACE Press this key to switch from Remote mode to SNAP SHOT Local mode, which allows you to control the...
Page 14: Ethernet Interface Features And Specifications
Ethernet Interface Features and Specifications Ethernet Interface Features Reception Features Allow you to specify the same settings that you can using the front panel keys. Receive output requests for measured and computed data, panel setting data, and error codes. Transmission Features The DLM2000 can transmit measured and computed data.
Page 15 2.2 Ethernet Interface Features and Specifications Switching between Remote and Local Modes Switching from Local to Remote Mode The DLM2000 switches to Remote mode when it is in Local mode and it receives a : COMMunicate:REMote ON command from the PC. •...
Page 16: Ethernet Interface Connection (Optional)
• Use a network cable that conforms to the transfer speed of your network. Note For details on how to connect the DLM2000 to a network, see section 18.1, “Connecting the DLM2000 to a Network” in the DLM2000 Series User’s Manual (IM710105-02E). IM 710105-17E...
Page 17: Configuring The Dlm2000 Network Settings
To use the Ethernet interface features, you must specify the following TCP/IP settings. • IP address • Subnet mask • Default gateway Index For instructions on how to specify these settings, see section 18.2, “Configuring TCP/IP Settings” in the DLM2000 Series User’s Manual (IM710105-02E). IM 710105-17E...
Page 18: Chapter 3 Gp-Ib Interface (Optional)
Chapter 3 GP-IB Interface (Optional) Component Names and Functions Front Panel UTILITY key Press this key to select the GP-IB interface. DLM2054 2.5GS/s 500MHz MIXED SIGNAL OSCILLOSCOPE PRINT MENU FILE UTILITY CLEAR CLEAR TRACE key (SHIFT+CLEAR TRACE) TRACE Press this key to switch from Remote mode to SNAP SHOT Local mode, which allows you to control the...
Page 19: Connecting Gp-Ib Cables (Optional)
• The DLM2000 may not operate properly if the DLM2000 is connected to the PC through converters (such as a GP-IB to USB converter). For more details, contact your nearest YOKOGAWA dealer. • Several cables can be used to connect multiple devices. However, no more than 15 devices, including the controller, can be connected on a single bus.
Page 20: Gp-Ib Interface Features
GP-IB Interface Features GP-IB Interface Features Listener Capabilities • Allows you to specify the same MLB2000 settings that you can using the front panel keys. You cannot turn the power on and off or change communication settings. • Receive output requests for measured and computed data, panel setting data, and error codes. •...
Page 21: Gp-Ib Interface Specifications
GP-IB Interface Specifications GP-IB Interface Specifications Electrical and mechanical specifications: IEEE St’d 488-1978 Functional specifications: See the table below. Protocol: IEEE St’d 488.2-1992 Code: ISO (ASCII) Mode: Addressable mode Address setup: You can set the address to a number from 0 to 30 on the GP-IB setup screen that you can access from the UTILITY menu.
Page 22: App
Configuring the DLM2000 GP-IB Settings This section explains the settings listed below. You must configure these settings when controlling the DLM2000 remotely through a GP-IB interface. • Communication interface • GP-IB address Opening the REMOTE CONTROL Menu Press UTILITY, and then press the REMOTE CONTROL soft key to open the following menu. Set the communication interface to GP-IB Set the address (0 to 30) Note...
Page 23: Responses To Interface Messages
Responses to Interface Messages Responses to Interface Messages Responses to Uni-Line Messages • IFC (Interface Clear) Clears the talker and listener functions. Stops data transmission if it is in progress. • REN (Remote Enable) Switches between Remote and Local modes. IDY (Identify) is not supported.
Page 24 3.6 Responses to Interface Messages Multi-line Messages Multi-line messages are sent over eight data lines. The messages are grouped as follows: • Address Commands Address commands are valid when the DLM2000 is designated as a listener or a talker. The following five commands are available.
Page 25: Chapter 4 Programming Overview Index
Chapter 4 Programming Overview Messages Messages Program Message Unit Syntax Messages are used to exchange information between The program message unit syntax is as follows: the controller and the DLM2000. Messages that are sent from the controller to the DLM2000 are called <Program header>...
Page 26 4.1 Messages Response Message Unit Syntax • If the controller sends a program message The response message unit syntax is as follows: containing multiple message units, but the message contains incomplete units, the DLM2000 will try to execute the ones that are believed to be complete. <Response header>...
Page 27: Commands
Commands Command When Concatenating Commands • Command Groups There are three types of commands (program headers) that a controller may send to the DLM2000. The A command group is a group of commands that commands differ in their program header formats. have common compound headers arranged in a hierarchy.
Page 28 4.2 Commands • When Separating Commands with <PMT> Header Interpretation Rules If you separate two commands with a terminator, The DLM2000 interprets the header that it receives two program messages will be sent. Therefore, according to the rules below. the common header must be specified for each command even if commands belonging to the same •...
Page 29: Responses
Responses Response When the controller sends a query with a question mark, the DLM2000 returns a response message to the query. The DLM2000 returns response messages in one of the following two forms. • Response Consisting of a Header and Data Responses that can be used as program messages without any changes are returned with command headers attached.
Page 30 Data Data • If a value has more significant digits than are Data contains conditions and values that are written available, the value will be rounded. after the header. A space separates the data from the <Voltage>, <Time>, <Frequency>, <Current> header.
Page 31: Data
4.4 Data <Register> • If a character string contains a double quotation mark ( " ), the double quotation mark is expressed as <Register> is an integer that can be expressed in two consecutive quotation marks ( "" ). This rule also decimal, hexadecimal, octal, or binary notation.
Page 32: Synchronization With The Controller
Synchronization with the Controller Overlap Commands and Sequential • Using the COMMunicate:OVERlap command The COMMunicate:OVERlap command enables (or Commands There are two types of commands: overlap and disables) overlapping. Example :COMMunicate:OVERlap #HFFBF;: sequential. The execution of one overlap command FILE:LOAD:SETup:EXECute can start before the execution of the previous overlap "CASE1";:CHANnel1:VDIV?<PMT>...
Page 33 4.5 Synchronization with the Controller Example TRIGger:MODE • Using the *OPC? Query The *OPC? query generates a response when an SINGle;:STARt<PMT> :STATus:CONDition?<PMT> overlapping operation is completed. Example :COMMunicate:OPSE #H0040;: (Read the response. If bit 0 is 1, return to FILE:LOAD:SETup:EXECute the previous command.) "CASE1";*OPC?<PMT>...
Page 34: Chapter 5 Commands
Chapter 5 Commands List of Commands Command Function Page ACQuire Group :ACQuire? Queries all waveform acquisition settings. 5-55 :ACQuire:AVERage? Queries all of the settings related to averaging and the number of waveform 5-55 acquisitions. :ACQuire:AVERage:COUNt Sets or queries the attenuation constant for exponential averaging or the 5-55 average count for linear averaging for Averaging mode.
Page 35 5.1 List of Commands Command Function Page :ANALysis:PANalyze<x>:I2T:MEASu Queries an automatically measured value of a Joule integral. 5-59 re:I2T:VALue? :ANALysis:PANalyze<x>:I2T:RANGe Sets or queries the measurement source window. 5-59 :ANALysis:PANalyze<x>:I2T:SCA Queries all scaling settings. 5-59 :ANALysis:PANalyze<x>:I2T:SCALe Sets or queries the center value for manual scaling. 5-60 :CENTer :ANALysis:PANalyze<x>:I2T:SCALe...
Page 36 5.1 List of Commands Command Function Page :ANALysis:PANalyze<x>:SETup:RTR Sets or queries the reference trace for power supply analysis deskewing. 5-64 :ANALysis:PANalyze<x>:SOA? Queries all XY display (safe operating area) settings. 5-64 :ANALysis:PANalyze<x>:SOA:CURS Queries all XY display (safe operating area) cursor measurement settings. 5-64 :ANALysis:PANalyze<x>:SOA:CURSo Queries all XY display (safe operating area) horizontal cursor settings.
Page 37 5.1 List of Commands Command Function Page :ANALysis:PANalyze<x>:SWLoss:SC Sets or queries the scaling mode. 5-68 ALe:MODE :ANALysis:PANalyze<x>:SWLoss:SC Sets or queries the span from the center value for manual scaling. 5-68 ALe:SENSitivity :ANALysis:PANalyze<x>:SWLoss:TR Sets or queries the measurement time period. 5-68 ANge (Time Range) :ANALysis:PANalyze<x>:SWLoss:UL Sets or queries the voltage level used to determine the loss calculation...
Page 38 5.1 List of Commands Command Function Page :ANALysis:PMEAsure<x>:UDPRoxima Sets or queries the distal, mesial, and proximal points as voltages. 5-73 l:UNIT :ANALysis:PMEAsure<x>:UMEThod Sets or queries the high and low points. 5-73 :ANALysis:PMEAsure<x>:UNIT Sets or queries the watthour unit. 5-73 :ANALysis:PMEAsure<x>:USER<y>? Queries all automatic measurement settings for a Calc item.
Page 39 5.1 List of Commands Command Function Page COMMunicate Group :COMMunicate? Queries all communication settings. 5-81 :COMMunicate:HEADer Sets or queries whether or not a header is added to the response to a query. 5-81 (Example with header: CHANNEL1:PROBE:MODE 10 . Example without header: 10 .) :COMMunicate:LOCKout Sets or clears local lockout.
Page 40 5.1 List of Commands Command Function Page :CURSor[:TY]:HORizontal:V<x>? Queries all vertical axis settings for a ΔV cursor. 5-85 :CURSor[:TY]:HORizontal:V<x>:ST Sets or queries the on/off status of the vertical value measured for a ΔV 5-85 cursor. :CURSor[:TY]:HORizontal:V<x>:VA Queries the vertical value of a ΔV cursor. 5-85 Lue? :CURSor[:TY]:MARKer? Queries all marker cursor settings. 5-85 :CURSor[:TY]:MARKer:FORM Sets or queries the marker cursor form. 5-85 :CURSor[:TY]:MARKer:M<x>? Queries all settings for the specified marker. 5-85 :CURSor[:TY]:MARKer:M<x>:ALL Collectively turns on or off the measured values of the marker cursor on the...
Page 41 5.1 List of Commands Command Function Page :CURSor[:TY]:VERTical:T<x>:VAL Queries the time value of a ΔT cursor. 5-88 :CURSor[:TY]:VERTical:TRACe Sets or queries the source waveform that you want to measure using the ΔT 5-88 cursors. :CURSor[:TY]:VERTical:V<x>? Queries all vertical axis settings for a ΔT cursor. 5-88 :CURSor[:TY]:VERTical:V<x>:STA Sets or queries the on/off status of the vertical value of a ΔT cursor. 5-88 :CURSor[:TY]:VERTical:V<x>:VAL Queries the vertical value of a ΔT cursor. 5-89 DISPlay Group :DISPlay? Queries all display settings. 5-90 :DISPlay:ACCumulate? Queries all accumulated waveform display settings. 5-90 :DISPlay:ACCumulate:MODE Sets or queries the accumulation mode.
Page 42 5.1 List of Commands Command Function Page :FFT<x>:MEASure? Queries all automatic measurement settings for FFT analysis. 5-94 :FFT<x>:MEASure:MARKer? Queries all marker cursor measurement settings for FFT analysis. 5-94 :FFT<x>:MEASure:MARKer[:BASic]? Queries all Basic marker cursor item settings for FFT analysis. 5-94 :FFT<x>:MEASure:MARKer[:BASic]: Collectively turns on or off all Basic marker cursor items for FFT analysis.
Page 43 5.1 List of Commands Command Function Page :FFT<x>:RPOSition Sets or queries the center point for magnifying the vertical axis for FFT 5-97 analysis. :FFT<x>:TRACe Sets or queries the source waveform for FFT analysis. 5-97 :FFT<x>:TYPE Sets or queries the spectrum for FFT analysis. 5-98 :FFT<x>:UNIT? Queries all FFT computation unit settings.
Page 44 5.1 List of Commands Command Function Page :FILE:SAVE:{ASCii|BINary}:LENG Sets or queries the number of data points to save when compressing or 5-102 sampling (decimating) various types of data. :FILE:SAVE:{ASCii|BINary}:RANGe Sets or queries the save range for a specific type of data. 5-102 :FILE:SAVE:{ASCii|BINary}:TRACe Sets or queries the waveforms to save for a specific type of data.
Page 45 5.1 List of Commands Command Function Page :GONogo[:ZPARameter]:NUMBer<x>: Queries all polygonal zone determination settings. 5-106 POLYgon? :GONogo[:ZPARameter]:NUMBer<x>: Sets or queries the horizontal position that will be used for polygonal zone 5-107 POLYgon:HPOSition determination. :GONogo[:ZPARameter]:NUMBer<x>: Sets or queries the source window that will be used for polygonal zone 5-107 POLYgon:RANGe determination.
Page 46 5.1 List of Commands Command Function Page :HCOPy:NETPrint:MODE Sets or queries whether the DLM2000 will print to the network printer in 5-111 normal copy or hard copy mode. :HCOPy:NETPrint:TONE Sets or queries the network printer output color setting. 5-111 :HCOPy:NETPrint:TYPE Sets or queries the network printer output command type.
Page 47 5.1 List of Commands Command Function Page :HISTory[:SEARch]:NUMBer<x>:REC Sets or queries the horizontal position of the rectangle that will be used for 5-115 Tangle:HORizontal rectangular zone searching. :HISTory[:SEARch]:NUMBer<x>:REC Sets or queries the source window of the rectangle that will be used for 5-115 Tangle:RANGe rectangular zone searching.
Page 48 5.1 List of Commands Command Function Page :LOGic[:PODA]:BIT<x>:LEVel Sets or queries the user-defined threshold level for a bit of a specified logic 5-120 input pod. :LOGic[:PODA]:BIT<x>:TYPE Selects the threshold level for a bit of a specified logic input pod. 5-120 :LOGic[:PODA]:DESKew Sets or queries the deskewing of a specified logic input pod.
Page 49 5.1 List of Commands Command Function Page :MATH<x>:USERdefine:DEFine Sets or queries the equation for user-defined computation. 5-126 :MATH<x>:USERdefine:FILTer<y>? Queries all filter settings for user-defined computation. 5-126 :MATH<x>:USERdefine:FILTer<y>:B Sets or queries the filter band (frequency band) for user-defined computation. 5-126 :MATH<x>:USERdefine:FILTer<y>:C Sets or queries the cutoff frequency for user-defined computation.
Page 50 5.1 List of Commands Command Function Page :MEASure:BIT<x>:<Parameter>? Queries the setting of a waveform parameter of a logic waveform. 5-130 :MEASure:BIT<x>:<Parameter>:COU Queries the statistical processing count of a logic waveform parameter. 5-130 :MEASure:BIT<x>:<Parameter>:{MA Queries a statistical value of a logic waveform parameter. 5-131 Ximum|MEAN|MINimum|SDEViation}? :MEASure:BIT<x>:<Parameter>:STA...
Page 51 5.1 List of Commands Command Function Page :MEASure:{CHANnel<x>|MATH<x>}:A Sets or queries the edge count of the reference waveform used to measure 5-136 REA2:DELay:REFerence:COUNt the delay between the specified waveform and the reference waveform in Area2. :MEASure:{CHANnel<x>|MATH<x>}:A Sets or queries the slope of the reference waveform used to measure the 5-136 REA2:DELay:REFerence:SLOPe delay between the specified waveform and the reference waveform in Area2.
Page 52 5.1 List of Commands Command Function Page :MEASure:CONTinuous:TLCHange Sets or queries whether normal statistical processing of automatically 5-141 (Trigger Level Change) measured waveform parameters is restarted when the trigger level is changed. :MEASure:CYCLe? Queries all cyclic statistical processing settings for automated measurement. 5-141 :MEASure:CYCLe:ABORt Aborts cyclic statistical processing for automated measurement.
Page 53 5.1 List of Commands Command Function Page :SEARch:PPATtern:BITS? Queries all bit settings for state or state edge searching. 5-147 :SEARch:PPATtern:BITS:HEXa Sets the bit search requirement in hexadecimal notation for state or state 5-147 width searching. :SEARch:PPATtern:BITS:PATTern Sets or queries the bit search requirement in binary notation for state or state 5-147 width searching.
Page 54 5.1 List of Commands Command Function Page :SERialbus<x>:CAN:DETail:DISPl Sets or queries the display mode for the CAN bus signal analysis result list. 5-153 :SERialbus<x>:CAN:DETail:LIST:I Queries all items that will be displayed in the CAN bus signal analysis result 5-153 TEM? list.
Page 55 5.1 List of Commands Command Function Page :SERialbus<x>:CAN:SEARch:SETup[ Sets or queries whether signed or unsigned data format will be used, which 5-157 :IDData]:DATA:SIGN is one of the ID and data conditions, for CAN bus signal searching. :SERialbus<x>:CAN:SEARch:SETup[ Queries all identifier settings for the ID and data conditions for CAN bus 5-157 :IDData]:IDENtifier? signal searching.
Page 56 5.1 List of Commands Command Function Page :SERialbus<x>:CANFD:SEARch:FJUM Jumps to the ACK Field in the CAN FD bus signal search result. 5-161 p:ACK :SERialbus<x>:CANFD:SEARch:FJUM Jumps to the Control Field in the CAN FD bus signal search result. 5-161 p:CONTrol :SERialbus<x>:CANFD:SEARch:FJUM Jumps to the CRC Field in the CAN FD bus signal search result.
Page 57 5.1 List of Commands Command Function Page :SERialbus<x>:CANFD:SEARch:SETu Sets or queries the data input format, which is one of the ID and data 5-165 p[:IDData]:DATA:PFORmat conditions, for CAN FD bus signal searching. :SERialbus<x>:CANFD:SEARch:SETu Sets or queries whether signed or unsigned data format will be used, which 5-165 p[:IDData]:DATA:SIGN is one of the ID and data conditions, for CAN FD bus signal searching.
Page 58 5.1 List of Commands Command Function Page :SERialbus<x>:FLEXray:SEARch:EX Executes a FLEXRAY bus signal search. 5-169 ECute :SERialbus<x>:FLEXray:SEARch:FJ Jumps to the cycle-count field in the FLEXRAY bus signal analysis results. 5-169 UMp:CCOunt :SERialbus<x>:FLEXray:SEARch:FJ Jumps to the CRC Field in the FLEXRAY bus signal analysis results. 5-169 UMp:CRC :SERialbus<x>:FLEXray:SEARch:FJ...
Page 59 5.1 List of Commands Command Function Page :SERialbus<x>:FLEXray:SEARch:SE Sets or queries the frame ID value, which is one of the ID and data 5-174 Tup[:IDData]:FID:ID<y> conditions, for FLEXRAY bus signal searching. :SERialbus<x>:FLEXray:SEARch:SE Sets or queries the frame ID enable/disable condition, which is one of the ID 5-174 Tup[:IDData]:FID:MODE and data conditions, for FLEXRAY bus signal searching.
Page 60 5.1 List of Commands Command Function Page :SERialbus<x>:I2C:SEARch[:SETu Queries all 7-bit address settings for I C bus signal searching. 5-177 p]:ADDRess:ADDRess[:BIT7ADdre ss]? :SERialbus<x>:I2C:SEARch[:SETup Sets the 7-bit address for I C bus signal searching in hexadecimal notation. 5-177 ]:ADDRess:ADDRess[:BIT7ADdress] :HEXa :SERialbus<x>:I2C:SEARch[:SETup Sets or queries the 7-bit address for I C bus signal searching in binary 5-177...
Page 61 5.1 List of Commands Command Function Page :SERialbus<x>:I2C:SEARch:SETup: Sets or queries the I C bus signal search type. 5-181 MODE :SERialbus<x>:I2C:SEARch:SETup: Queries all NON ACK ignore mode settings for I C bus signal searching. 5-181 NONack? :SERialbus<x>:I2C:SEARch:SETup: Sets or queries whether or not NON ACK will be ignored in high-speed mode 5-181 NONack:HSMode for I...
Page 62 5.1 List of Commands Command Function Page :SERialbus<x>:LIN:SEARch:SETup: Sets or queries the data conditions for LIN bus signal searching. 5-184 IDData:DATA:CONDition :SERialbus<x>:LIN:SEARch:SETup: Sets or queries the number of data bytes for LIN bus signal searching. 5-185 IDData:DATA:DBYTe :SERialbus<x>:LIN:SEARch:SETup: Sets or queries the data value for LIN bus signal searching in decimal 5-185 IDData:DATA:DECimal<y>...
Page 63 5.1 List of Commands Command Function Page :SERialbus<x>:PSI5:DETail:DISPl Sets or queries the display mode for the PSI5 signal analysis list. 5-189 :SERialbus<x>:PSI5:DETail:LIST: Queries all the data for all analysis numbers in the PSI5 signal analysis result 5-189 ALL? list. :SERialbus<x>:PSI5:DETail:LIST: Queries all items that will be displayed in the PSI5 signal analysis result list.
Page 64 5.1 List of Commands Command Function Page :SERialbus<x>:PSI5:TRENd<y>:CUR Queries the vertical value between cursors on the PSI5 signal analysis trend 5-193 Sor:DV:VALue? display. :SERialbus<x>:PSI5:TRENd<y>:CUR Sets or queries the cursor mode on the PSI5 signal analysis trend display. 5-193 Sor:MODE :SERialbus<x>:PSI5:TRENd<y>:CUR Sets or queries the position of the specified cursor on the PSI5 signal 5-193 Sor:POSition<z>...
Page 65 5.1 List of Commands Command Function Page :SERialbus<x>:SENT[:ANALyze]:SE Sets or queries the SENT signal analysis specification version. 5-197 Tup:FORMat:VERSion :SERialbus<x>:SENT[:ANALyze]:SE Sets or queries the SENT signal analysis slow channel format. 5-197 Tup:STYPe :SERialbus<x>:SENT[:ANALyze]:SE Sets or queries the SENT signal analysis source. 5-197 Tup:SOURce :SERialbus<x>:SENT:DETail?
Page 66 5.1 List of Commands Command Function Page :SERialbus<x>:SENT:SEARch:[SETu Sets or queries the SENT signal search fast channel status and 5-201 p]:FSAComm:PATTern communication nibble data in binary notation. :SERialbus<x>:SENT:SEARch:[SETu Sets or queries the data input format, which is one of the fast channel status 5-201 p]:FSAComm:PFORmat and communication nibble data conditions, for SENT signal searching.
Page 67 5.1 List of Commands Command Function Page :SERialbus<x>:SENT:SEARch[:SETu Sets or queries the data input format, which is one of the slow channel 5-205 p]:SDATa:ENHanced:D16Bit:DATA:P enhanced type 16-bit data and 4-bit ID data conditions, for SENT signal FORmat searching. :SERialbus<x>:SENT:SEARch[:SETu Queries all ID settings related to the slow channel enhanced type 16-bit data 5-205 p]:SDATa:ENHanced:D16Bit:ID? and 4-bit ID for SENT signal searching.
Page 68 5.1 List of Commands Command Function Page :SERialbus<x>:SENT:TRENd<y>:UDA Sets or queries the fast channel user-defined data of the SENT signal 5-208 analysis trend display. :SERialbus<x>:SENT:TRENd<y>:VER Sets or queries the vertical range of the SENT signal analysis trend display. 5-209 Tical :SERialbus<x>:SENT:TRENd<y>:VTD Sets or queries the on/off status of the VT waveform display on the SENT 5-209...
Page 69 5.1 List of Commands Command Function Page :SERialbus<x>:SPATtern:SEARch:S Sets or queries the data condition for user-defined bus signal searching in 5-213 ETup:PATTern binary notation. :SERialbus<x>:SPATtern:SEARch:S Sets or queries the input format, which is one of the data conditions, for user- 5-213 ETup:PFORmat defined bus signal searching.
Page 70 5.1 List of Commands Command Function Page :SERialbus<x>:SPI:SEARch[:SETup Sets or queries the data enable/disable condition for SPI bus signal 5-217 ]:DATA<y>:MODE searching. :SERialbus<x>:SPI:SEARch[:SETup Sets or queries the data value for SPI bus signal searching in binary notation. 5-217 ]:DATA<y>:PATTern<z> :SERialbus<x>:SPI:SEARch[:SETup Sets or queries the input format, which is one of the data conditions, for SPI 5-217 ]:DATA<y>:PFORmat...
Page 71 5.1 List of Commands Command Function Page :SERialbus<x>:UART:SEARch:SETup Sets or queries the UART signal search parity mode setting. 5-221 :ERRor:PMODe :SERialbus<x>:UART:SEARch:SETup Sets or queries the format setting for UART signal analysis. 5-222 :FORMat :SERialbus<x>:UART:SEARch:SETup Sets or queries the UART signal search mode. 5-222 :MODE :SERialbus<x>:ZLINkage...
Page 72 5.1 List of Commands Command Function Page :SYSTem:DCANcel (Delay Cancel) Sets or queries whether or not the specified delay value will be applied to 5-229 time measurement (on/off). :SYSTem:FSIZe? (Font Size) Queries all font size settings. 5-229 :SYSTem:FSIZe:MEASure Sets or queries the font size that is used to display the automatically 5-229 measured waveform parameters and the cursor measurement values.
Page 73 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the CAN bus signal trigger error frame setting. 5-234 :CAN:EFRame[:MODE] :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the CAN bus signal trigger stuff error setting. 5-234 :CAN:EFRame:STUFF :TRIGger{[:ATRigger]|:BTRigger} Queries all ID and data condition settings for CAN bus signal triggering. 5-234 :CAN[:IDData]? :TRIGger{[:ATRigger]|:BTRigger}...
Page 74 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets a signal reference value, which is one of the ID and data conditions, for 5-238 :CAN[:IDData]:MSIGnal:SIGNal:DE CAN bus signal triggering in decimal notation. Cimal<x> :TRIGger{[:ATRigger]|:BTRigger} Sets the signal item, which is one of the ID and data conditions, for CAN bus 5-238 :CAN[:IDData]:MSIGnal:SIGNal:IT signal triggering.
Page 75 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Queries all ID and data condition settings for FLEXRAY bus signal triggering. 5-241 :FLEXray:IDData? :TRIGger{[:ATRigger]|:BTRigger} Queries all cycle-count settings for the ID and data conditions for FLEXRAY 5-241 :FLEXray[:IDData]:CCOunt? bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the cycle-count data condition, which is one of the ID and 5-241...
Page 76 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the indicator start frame, which is one of the ID and data 5-245 :FLEXray[:IDData]:INDIcator:STF conditions, for FLEXRAY bus signal triggering. Rame :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the indicator sync frame, which is one of the ID and data 5-245 :FLEXray[:IDData]:INDIcator:SYF conditions, for FLEXRAY bus signal triggering.
Page 77 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the 7-bit address for the 7-bit + sub address for I C bus 5-248 :I2C:ADDRess:ADDRess:BIT7APsub: signal triggering in binary notation. ADDRess:PATTern :TRIGger{[:ATRigger]|:BTRigger} Queries all sub address settings for the 7-bit + sub address for I C bus signal 5-248 :I2C:ADDRess:ADDRess:BIT7APsub:...
Page 78 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Queries all LIN bus signal trigger settings. 5-252 :LIN? :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the LIN bus signal trigger break length. 5-252 :LIN:BLENgth :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the LIN bus signal trigger bit rate (data transfer rate). 5-252 :LIN:BRATe :TRIGger{[:ATRigger]|:BTRigger}...
Page 79 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the ID input format, which is one of the IDOR conditions, for 5-256 :LIN:IDOR:IDENtifier:PFORmat LIN bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the LIN bus signal trigger mode setting. 5-256 :LIN:MODE :TRIGger{[:ATRigger]|:BTRigger}...
Page 80 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Queries all clock signal settings for user-defined bus signal triggering. 5-259 :SPATtern:CLOCk? :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the clock signal enable or disable status for user-defined bus 5-260 :SPATtern:CLOCk:MODE signal triggering. :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the clock signal polarity for user-defined bus signal triggering. 5-260 :SPATtern:CLOCk:POLarity :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the clock signal for user-defined bus signal triggering.
Page 81 5.1 List of Commands Command Function Page :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the data signal for SPI bus signal triggering. 5-264 :SPI:DATA<x>:SOURce :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the wiring system (three-wire or four-wire) for SPI bus signal 5-264 :SPI:MODE triggering. :TRIGger{[:ATRigger]|:BTRigger} Sets or queries the trigger type. 5-264 :TYPE :TRIGger{[:ATRigger]|:BTRigger}...
Page 82 5.1 List of Commands Command Function Page :TRIGger[:ATRigger]:CANFD[:ID]: Sets or queries the ID condition, which is one of the ID conditions, for CAN 5-267 IDENtifier:ID:PATTern FD bus signal triggering in binary notation. :TRIGger[:ATRigger]:CANFD[:ID]: Sets or queries the ID frame format (standard or extended), which is one of 5-268 IDENtifier:MFORmat the ID conditions, for CAN FD bus signal triggering.
Page 83 5.1 List of Commands Command Function Page :TRIGger[:ATRigger]:PSI5:SETup: Sets or queries the error detection method for PSI5 signal triggering. 5-272 DATA:EDETection :TRIGger[:ATRigger]:PSI5:SETup: Sets or queries the data source for PSI5 signal triggering. 5-272 DATA:SOURce :TRIGger[:ATRigger]:PSI5:SETup: Sets or queries the sync signal for PSI5 signal triggering. 5-272 SYNC :TRIGger[:ATRigger]:PULSe?
Page 84 5.1 List of Commands Command Function Page :TRIGger[:ATRigger]:WIDTh:CLOCk Sets or queries the clock signal for state width triggering. 5-276 :SOURce :TRIGger[:ATRigger]:WIDTh:CONDi Sets or queries the trigger condition for state width triggering. 5-276 tion :TRIGger[:ATRigger]:WIDTh:LOGic Sets or queries the combination condition for state width triggering. 5-276 :TRIGger[:ATRigger]:WIDTh:TIME Sets or queries the pulse width setting for state width triggering.
Page 85 5.1 List of Commands Command Function Page :WAVeform:SRATe? (Sample RATE) Queries the sample rate of the record specified by the :WAVeform:RECord 5-281 command. :WAVeform:STARt Sets or queries which point will be used as the first data value for the 5-281 waveform specified by :WAVeform:TRACe .
Page 86 5.1 List of Commands Command Function Page XY Group :XY<x>? Queries all XY display settings. 5-286 :XY<x>:DISPlay Sets or queries the on/off status of the XY display. 5-286 :XY<x>:MEASure? Queries all automated measurement settings for the XY display. 5-286 :XY<x>:MEASure:CURSor? Queries all cursor measurement settings for the XY display.
Page 87 5.1 List of Commands Command Function Page Common Command Group *CAL? (CALibrate) Executed calibration and queries the result. 5-291 *CLS (CLear Status) Clears the standard event register, extended event register, and error queue. 5-291 *ESE (standard Event Status Sets or queries the standard event enable register. 5-291 Enable register) *ESR? (standard Event Status...
Page 88: Acquire Group
ACQuire Group :ACQuire? :ACQuire:RESolution Function Queries all waveform acquisition settings. Function Sets or queries the on/off status of High Resolution :ACQuire? Syntax mode. :ACQuire:RESolution {<Boolean>} Syntax :ACQuire:AVERage? :ACQUIRE:RESOLUTION ON Example :ACQUIRE:RESOLUTION? Function Queries all of the settings related to averaging and ->...
Page 89: Analysis Group
ANALysis Group :ANALysis:PANalyze and :ANALysis:PMEAsure commands) The power supply analysis feature ( is an option available only for 4-channel models. Power supply analysis commands cannot be used on 2-channel models or 4-channel models without the power supply analysis option. :ANALysis? :ANALysis:AHIStogram<x>:MEASure:MODE Function Queries all of the settings for the analysis feature.
Page 90 5.3 ANALysis Group :ANALysis:AHIStogram<x>:MEASure:PARa :ANALysis:AHIStogram<x>:MEASure:PARa meter:<Parameter>:STATe meter:HPOSition<y> Function Sets or queries the on/off status of the specified Function Sets or queries the horizontal position of Cursor1 measurement item of a waveform histogram. or Cursor 2 for a waveform histogram. :ANALysis:AHIStogram<x>:MEASure:PARam :ANALysis:AHIStogram<x>:MEASure:PARam Syntax Syntax...
Page 91 5.3 ANALysis Group :ANALysis:AHIStogram<x>:MODE :ANALysis:PANalyze<x>? Function Sets or queries the target axis of a waveform Function Queries all power supply analysis settings. :ANALysis:PANalyze<x>? histogram. Syntax :ANALysis:AHIStogram<x>:MODE {HORizon Syntax <x> = 1 or 2 tal|VERTical} :ANALysis:PANalyze<x>:I2T? :ANALysis:AHIStogram<x>:MODE? <x> = 1 or 2 (1 only for 2-channel models) Function Queries all Joule integral settings.
Page 92 5.3 ANALysis Group :ANALysis:PANalyze<x>:I2T:MEASure:I2 :ANALysis:PANalyze<x>:I2T:MEASure:I2 T:{MAXimum|MEAN|MINimum|SDEViation}? T:VALue? Function Queries a statistical value of a Joule integral. Function Queries an automatically measured value of a :ANALysis:PANalyze<x>:I2T:MEASure:I2T Syntax Joule integral. :{MAXimum|MEAN|MINimum| :ANALysis:PANalyze<x>:I2T:MEASure:I2T Syntax SDEViation}? :VALue? [{<NRf>}] <x> = 1 or 2 <x> = 1 or 2 :ANALYSIS:PANALYZE1:I2T:MEASURE:I2T:M Example <NRf>...
Page 93 5.3 ANALysis Group :ANALysis:PANalyze<x>:I2T:SCALe:CENT :ANALysis:PANalyze<x>:I2T:TRANge (Time Range) Function Sets or queries the center value for manual Function Sets or queries the measurement time period. :ANALysis:PANalyze<x>:I2T:TRAN scaling. Syntax :ANALysis:PANalyze<x>:I2T:SCALe:CENT ge {<NRf>,<NRf>} Syntax er {<NRf>} :ANALysis:PANalyze<x>:I2T:TRANge? :ANALysis:PANalyze<x>:I2T:SCALe:CENT <x> = 1 or 2 <NRf> = −5 to 5 divisions (in steps of 10 divisions/ <x>...
Page 94 5.3 ANALysis Group :ANALysis:PANalyze<x>:HARMonics:CCLa :ANALysis:PANalyze<x>:HARMonics:DCLa ss:MAXCurrent ss:POWer Function Sets or queries the fundamental current value for Function Sets or queries the power value for class D class C harmonic analysis. harmonic analysis. :ANALysis:PANalyze<x>:HARMonics:CCLas :ANALysis:PANalyze<x>:HARMonics:DCLas Syntax Syntax s:MAXCurrent {<NRf>|<Current>} s:POWer {<NRf>} :ANALysis:PANalyze<x>:HARMonics:CCLas :ANALysis:PANalyze<x>:HARMonics:DCLas s:MAXCurrent?
Page 95 5.3 ANALysis Group :ANALysis:PANalyze<x>:HARMonics:DETa :ANALysis:PANalyze<x>:HARMonics:SPOi il:LIST:ITEM? Function Queries the items displayed in the harmonic Function Sets or queries the harmonic analysis computation analysis result list. start point. :ANALysis:PANalyze<x>:HARMonics:DETai :ANALysis:PANalyze<x>:HARMonics:SPOi Syntax Syntax l:LIST:ITEM? nt {<NRf>} :ANALysis:PANalyze<x>:HARMonics:SPOi <x> = 1 or 2 :ANALYSIS:PANALYZE1:HARMONICS:DETAIL: Example LIST:ITEM?
Page 96 5.3 ANALysis Group :ANALysis:PANalyze<x>:SETup:I? :ANALysis:PANalyze<x>:SETup:U? Function Queries all current input channel settings for Function Queries all voltage input channel settings for power supply analysis. power supply analysis. :ANALysis:PANalyze<x>:SETup:I? :ANALysis:PANalyze<x>:SETup:U? Syntax Syntax <x> = 1 or 2 <x> = 1 or 2 :ANALysis:PANalyze<x>:SETup:I:DESKew :ANALysis:PANalyze<x>:SETup:U:DESKew Function...
Page 97 5.3 ANALysis Group :ANALysis:PANalyze<x>:SETup:RTRace :ANALysis:PANalyze<x>:SOA:CURSor:X<y >:VALue? Function Sets or queries the reference trace for power supply analysis deskewing. Function Sets or queries the voltage value of a horizontal :ANALysis:PANalyze<x>:SETup:RTRa Syntax cursor in the XY display (safe operating area). ce {I|U} :ANALysis:PANalyze<x>:SOA:CURSor:X<y>...
Page 98 5.3 ANALysis Group :ANALysis:PANalyze<x>:SOA:MODE :ANALysis:PANalyze<x>:SWLoss? Function Sets or queries the automated measurement Function Queries all switching loss settings. :ANALysis:PANalyze<x>:SWLoss? mode of the XY display (safe operating area). Syntax :ANALysis:PANalyze<x>:SOA:MODE {CURSo Syntax <x> = 1 or 2 r|OFF} Description Use the commands listed below to set the :ANALysis:PANalyze<x>:SOA:MODE? reference levels (distal, mesial, proximal, etc.) <x>...
Page 99 5.3 ANALysis Group :ANALysis:PANalyze<x>:SWLoss:DPROxim :ANALysis:PANalyze<x>:SWLoss:ILEVel al:PERCent Function Sets or queries the current level used to determine Function Sets or queries the distal, mesial, and proximal the zero loss period for total loss computation. :ANALysis:PANalyze<x>:SWLoss:ILEV points as percentages. Syntax :ANALysis:PANalyze<x>:SWLoss:DPROxima el {<NRf>|<Current>} Syntax l:PERCent {<NRf>,<NRf>,<NRf>} :ANALysis:PANalyze<x>:SWLoss:ILEVel?
Page 100 5.3 ANALysis Group :ANALysis:PANalyze<x>:SWLoss:MEASure :ANALysis:PANalyze<x>:SWLoss:MEASure :<Parameter>:COUNt? :<Parameter>:VALue? Function Queries the continuous statistical processing Function Queries an automatically measured value of a count of a power supply analysis parameter. power supply analysis parameter. :ANALysis:PANalyze<x>:SWLoss:MEASure: :ANALysis:PANalyze<x>:SWLoss:MEASure: Syntax Syntax P:COUNt? <Parameter>:VALue? [{<NRf>}] <x> = 1 or 2 <x>...
Page 101 5.3 ANALysis Group :ANALysis:PANalyze<x>:SWLoss:RANGe :ANALysis:PANalyze<x>:SWLoss:SCALe:M Function Sets or queries the measurement source window. :ANALysis:PANalyze<x>:SWLoss:RAN Syntax Function Sets or queries the scaling mode. Ge {MAIN|Z1|Z2} :ANALysis:PANalyze<x>:SWLoss:SCALe:MO Syntax :ANALysis:PANalyze<x>:SWLoss:RANGe? DE {AUTO|MANual} :ANALysis:PANalyze<x>:SWLoss:SCALe:MO <x> = 1 or 2 :ANALYSIS:PANALYZE1:SWLOSS:RANGE MAIN Example :ANALYSIS:PANALYZE1:SWLOSS:RANGE? <x> = 1 or 2 ->...
Page 102 5.3 ANALysis Group :ANALysis:PANalyze<x>:SWLoss:ULEVel :ANALysis:PMEAsure<x>? Function Sets or queries the voltage level used to Function Queries all power measurement settings. :ANALysis:PMEAsure<x>? determine the loss calculation period for total loss Syntax computation. <x> = 1 to 2 :ANALysis:PANalyze<x>:SWLoss:ULEV :ANALYSIS:PMEASURE1? Syntax Example el {<NRf>|<Voltage>} ->...
Page 103 5.3 ANALysis Group :ANALysis:PMEAsure<x>:IDPRoximal:UN :ANALysis:PMEAsure<x>:MEASure:<Param eter>? Function Sets or queries the distal, mesial, and proximal Function Queries the setting of a power measurement points as voltages. parameter. :ANALysis:PMEAsure<x>:IDPRoximal:UN :ANALysis:PMEAsure<x>:MEASure:<Parame Syntax Syntax IT {<NRf>,<NRf>,<NRf>} ter>? :ANALysis:PMEAsure<x>:IDPRoximal:UN <x> = 1 to 2 :ANALYSIS:PMEASURE1:MEASURE:AH? Example <x>...
Page 104 5.3 ANALysis Group :ANALysis:PMEAsure<x>:MEASure:<Param :ANALysis:PMEAsure<x>:RANGe eter>:STATe Function Sets or queries the measurement source window. :ANALysis:PMEAsure<x>:RANGe {MAIN| Function Queries the on/off status of the power Syntax Z1|Z2} measurement parameter. :ANALysis:PMEAsure<x>:MEASure:<Parame :ANALysis:PMEAsure<x>:RANGe? Syntax ter>:STATe {<Boolean>} <x> = 1 to 2 :ANALysis:PMEAsure<x>:MEASure:<Parame :ANALYSIS:PMEASURE1:RANGE MAIN Example ter>:STATe? :ANALYSIS:PMEASURE1:RANGE?
Page 105 5.3 ANALysis Group :ANALysis:PMEAsure<x>:SETup:I:PROBe :ANALysis:PMEAsure<x>:SETup:U:PROBe Function Queries all current-to-voltage conversion ratio Function Queries all voltage-to-voltage conversion ratio settings of the probe connected to the current settings of the probe connected to the voltage input channel for power measurement. input channel for power measurement. :ANALysis:PMEAsure<x>:SETup:I:PRO :ANALysis:PMEAsure<x>:SETup:U:PRO Syntax...
Page 106 5.3 ANALysis Group :ANALysis:PMEAsure<x>:UDPRoximal:PER :ANALysis:PMEAsure<x>:USER<y>? Cent Function Queries all automatic measurement settings for a Function Sets or queries the distal, mesial, and proximal Calc item. :ANALysis:PMEAsure<x>:USER<y>? points as percentages. Syntax :ANALysis:PMEAsure<x>:UDPRoximal:PERC Syntax <x> = 1 to 2 ent {<NRf>,<NRf>,<NRf>} <y> = 1 to 4 :ANALysis:PMEAsure<x>:UDPRoximal:PERC :ANALYSIS:PMEASURE:USER? Example...
Page 107 5.3 ANALysis Group :ANALysis:PMEAsure<x>:USER<y>:STATe :ANALysis:WAIT? Function Sets or queries the on/off status of automated Function Waits for the completion of automated measurement of a Calc item. measurement with a set timeout. :ANALysis:PMEAsure<x>:USER<y>:STA :ANALysis:WAIT? {<NRf>} Syntax Syntax Te {<Boolean>} <NRf> = 1 to 36000 (the timeout specified in 100 :ANALysis:PMEAsure<x>:USER<y>:STATe? ms intervals) :ANALYSIS:WAIT?
Page 108: Asetup Group
ASETup Group :ASETup:EXECute Function Executes auto setup. :ASETup:EXECute Syntax :ASETUP:EXECUTE Example :ASETup:UNDO Function Undoes auto setup. :ASETup:UNDO Syntax :ASETUP:UNDO Example Index 5-75 IM 710105-17E...
Page 109: Calibrate Group
CALibrate Group :CALibrate? Function Queries all calibration settings. :CALibrate? Syntax :CALibrate[:EXECute] Function Executes calibration. :CALibrate[:EXECute] Syntax :CALIBRATE:EXECUTE Example :CALibrate:MODE Function Sets or queries the on/off status of auto calibration. :CALibrate:MODE {AUTO|OFF} Syntax :CALIBRATE:MODE AUTO Example :CALIBRATE:MODE? -> :CALIBRATE:MODE AUTO 5-76 IM 710105-17E...
Page 110: Channel Group
CHANnel Group :CHANnel<x>? :CHANnel<x>:DESKew Function Queries all vertical axis settings of a channel. Function Sets or queries the deskew setting of a channel. :CHANnel<x>? :CHANnel<x>:DESKew {<Time>} Syntax Syntax :CHANnel<x>:DESKew? <x> = 1 to 4 (1 or 2 for 2-channel models) <x>...
Page 111 5.6 CHANnel Group :CHANnel<x>:LABel:DISPlay :CHANnel<x>:LSCale:UNIT Function Sets or queries the waveform label display on/off Function Sets or queries a unit that is attached to linear status of a channel. scaling results. :CHANnel<x>:LABel:DISPlay {<Boolean>} :CHANnel<x>:LSCale:UNIT {<String>} Syntax Syntax :CHANnel<x>:LABel:DISPlay? :CHANnel<x>:LSCale:UNIT? <x> = 1 to 4 (1 or 2 for 2-channel models) <x>...
Page 112 5.6 CHANnel Group :CHANnel<x>:PROBe[:MODE] Function Sets or queries the probe attenuation setting of a channel. :CHANnel<x>:PROBe[:MODE] {<NRf>| Syntax C0_001|C0_002|C0_005|C0_01|C0_02| C0_05|C0_1|C0_2|C0_5|C1|C2|C5|C10| C20|C50|C100|C200|C500|C1000|C2000} :CHANnel<x>:PROBe[:MODE]? <x> = 1 to 4 (1 or 2 for 2-channel models) :CHANNEL1:PROBE:MODE <NRF> Example :CHANNEL1:PROBE:MODE? -> :CHANNEL1:PROBE:MODE <NRF> :CHANnel<x>:PROBe:PZCalibrate Function Executes zero calibration of current probes for a...
Page 113: Clear Group
CLEar Group :CLEar Function Clears traces. :CLEar Syntax :CLEAR Example 5-80 IM 710105-17E...
Page 114: Communicate Group
COMMunicate Group The commands in this group deal with communication. There are no front panel keys that correspond to the commands in this group. :COMMunicate:OPSR? (Operation :COMMunicate? Pending Status Register) Function Queries all communication settings. :COMMunicate? Function Queries the operation pending status register. Syntax :COMMunicate:OPSR? Syntax...
Page 115 5.8 COMMunicate Group :COMMunicate:VERBose Function Sets or queries whether the response to a query is returned fully spelled out (example: CHANNEL1:PROBE:MODE 10 ) or using abbreviation (example: CHAN:PROB 10 ). :COMMunicate:VERBose {<Boolean>} Syntax :COMMunicate:VERBose? :COMMUNICATE:VERBOSE ON Example :COMMUNICATE:VERBOSE? -> :COMMUNICATE:VERBOSE 1 :COMMunicate:WAIT Function Waits for a specified extended event to occur.
Page 116: Cursor Group
CURSor Group :CURSor? :CURSor[:TY]:DEGRee:DD:STATe Function Queries all cursor measurement settings. Function Sets or queries the on/off status of the angle :CURSor? Syntax difference value ΔD, which is measured between the angle cursors. :CURSor[:TY]? :CURSor[:TY]:DEGRee:DD:STATe {<Boolea Syntax n>} Function Queries all cursor settings. :CURSor[:TY]? :CURSor[:TY]:DEGRee:DD:STATe? Syntax :CURSOR:TY:DEGREE:DD:STATE ON Example :CURSor[:TY]:DEGRee? :CURSOR:TY:DEGREE:DD:STATE?
Page 117 5.9 CURSor Group :CURSor[:TY]:DEGRee:POSition<x> :CURSor[:TY]:DEGRee:UNIT Function Sets or queries the position of an angle cursor. Function Sets or queries the unit of angle cursor :CURSor[:TY]:DEGRee:POSition<x> {<NRf Syntax measurement. >} :CURSor[:TY]:DEGRee:UNIT {<String>} Syntax :CURSor[:TY]:DEGRee:POSition<x>? :CURSor[:TY]:DEGRee:UNIT? <x> = 1 or 2 <String> = Up to four characters :CURSOR:TY:DEGREE:UNIT "DEG"...
Page 118 5.9 CURSor Group :CURSor[:TY]:HORizontal:DV:STATe :CURSor[:TY]:HORizontal:V<x>:STATe Function Sets or queries the on/off status of the vertical Function Sets or queries the on/off status of the vertical value measured between the ΔV cursors. value measured for a ΔV cursor. :CURSor[:TY]:HORizontal:DV:STA :CURSor[:TY]:HORizontal:V<x>:STA Syntax Syntax Te {<Boolean>} Te {<Boolean>} :CURSor[:TY]:HORizontal:DV:STATe? :CURSor[:TY]:HORizontal:V<x>:STATe? :CURSOR:TY:HORIZONTAL:DV:STATE ON Example <x>...
Page 119 5.9 CURSor Group :CURSor[:TY]:MARKer:M<x>:DT<x>:STATe :CURSor[:TY]:MARKer:M<x>:JUMP Function Sets or queries the on/off status of the time value Function Makes a marker cursor in the T-Y display jump to measured between marker cursors. the specified zoom waveform. :CURSor[:TY]:MARKer:M<x>:DT<x>:STA :CURSor[:TY]:MARKer:M<x>:JUMP {Z1|Z2} Syntax Syntax Te {<Boolean>} <x>...
Page 120 5.9 CURSor Group :CURSor[:TY]:MARKer:M<x>:TRACe :CURSor[:TY]:TYPE Function Sets or queries the source waveform that you Function Sets or queries the cursor type. :CURSor[:TY]:TYPE {OFF|HORizontal| want to measure using the marker cursors. Syntax :CURSor[:TY]:MARKer:M<x>:TRACe {<NRf> HAVertical|MARKer|VERTical|DEGRee} Syntax |MATH<y>|OFF} :CURSor[:TY]:TYPE? :CURSor[:TY]:MARKer:M<x>:TRACe? :CURSOR:TY:TYPE HORizontal Example :CURSOR:TY:TYPE? <x>...
Page 121 5.9 CURSor Group :CURSor[:TY]:VERTical:DV:VALue? :CURSor[:TY]:VERTical:T<x>? Function Queries the vertical value between the ΔT cursors. Function Queries all time axis settings for a ΔT cursor. :CURSor[:TY]:VERTical:DV:VALue? :CURSor[:TY]:VERTical:T<x>? Syntax Syntax :CURSOR:TY:VERTICAL:DV:VALUE? Example <x> = 1 or 2 -> :CURSOR:TY:VERTICAL:DV:VALUE 1.50E :CURSor[:TY]:VERTical:T<x>:STATe Description When linear scaling is on, the DLM2000 returns Function Sets or queries the on/off status of the time value the scaled value.
Page 122 5.9 CURSor Group :CURSor[:TY]:VERTical:V<x>:VALue? Function Queries the vertical value of a ΔT cursor. :CURSor[:TY]:VERTical:V<x>:VALue? Syntax <x> = 1 or 2 :CURSOR:TY:VERTICAL:V1:VALUE? Example -> :CURSOR:TY:VERTICAL:V1:VALUE 2.50E Index 5-89 IM 710105-17E...
Page 123: Display Group
5.10 DISPlay Group :DISPlay? :DISPlay:COLor:LSTate Function Queries all display settings. Function Sets or queries the color of the logic-waveform :DISPlay? Syntax state display. :DISPlay:COLor:LSTate {BLUE|BGReen| Syntax :DISPlay:ACCumulate? CYAN|DBLue|GRAY|GREen|LBLue|LGReen| MAGenta|MGReen|ORANge|PINK|PURPle| Function Queries all accumulated waveform display RED|SPINk|YELLow} settings. :DISPlay:ACCumulate? :DISPlay:COLor:LSTate? Syntax :DISPLAY:COLOR:LSTATE BLUE Example :DISPlay:ACCumulate:MODE...
Page 124 5.10 DISPlay Group :DISPlay:FGRid :DISPlay:MAPPing Function Sets or queries the on/off status of the fine grid Function Sets or queries the split screen waveform mapping display. mode. :DISPlay:FGRid {<Boolean>} :DISPlay:MAPPing {AUTO|MANual} Syntax Syntax :DISPlay:FGRid? :DISPlay:MAPPing? :DISPLAY:FGRID ON :DISPLAY:MAPPING AUTO Example Example :DISPLAY:FGRID? :DISPLAY:MAPPING?
Page 125: Fft Group
5.11 FFT Group :FFT<x>:DATA:END :FFT<x>? Function Sets or queries the end point of the FFT waveform Function Queries all of the settings for the FFT analysis data that will be sent. feature. :FFT<x>:DATA:END {<NRf>} Syntax :FFT<x>? Syntax :FFT<x>:DATA:END? <x> = 1 or 2 (1 only for 2-channel models) <x>...
Page 126 5.11 FFT Group :FFT<x>:HORizontal:CSPan:SPAN :FFT<x>:DATA:STARt Function Sets or queries the span value of the horizontal Function Sets or queries the start point of the FFT axis for FFT analysis. waveform data that will be sent. :FFT<x>:HORizontal:CSPan:SPAN {<Frequ Syntax :FFT<x>:DATA:STARt {<NRf>} Syntax ency>} :FFT<x>:DATA:STARt?
Page 127 5.11 FFT Group :FFT<x>:MEASure? :FFT<x>:MEASure:MARKer[:BASic]:DFReq uency:VALue? Function Queries all automatic measurement settings for FFT analysis. Function Queries the frequency between marker cursors for :FFT<x>:MEASure? Syntax FFT analysis. :FFT<x>:MEASure:MARKer[:BASic]:DFRequ <x> = 1 or 2 (1 only for 2-channel models) Syntax ency:VALue? :FFT<x>:MEASure:MARKer? <x>...
Page 128 5.11 FFT Group :FFT<x>:MEASure:MARKer[:BASic]:FREQu :FFT<x>:MEASure:MARKer[:BASic]:V<y>: ency<y>:STATe STATe Function Sets or queries the on/off status of the frequency Function Sets or queries the on/off status of the level of of marker cursor for FFT analysis. marker cursor for FFT analysis. :FFT<x>:MEASure:MARKer[:BASic]:FREQue :FFT<x>:MEASure:MARKer[:BASic]:V<y>:S Syntax Syntax...
Page 129 5.11 FFT Group :FFT<x>:MEASure:PEAK[:BASic]:ALL :FFT<x>:MEASure:PEAK[:BASic]:DV:STA Function Collectively turns on or off all Basic peak items for FFT analysis. Function Sets or queries the on/off status of the power :FFT<x>:MEASure:PEAK[:BASic]:A Syntax measured between peak values for FFT analysis. LL {<Boolean>} :FFT<x>:MEASure:PEAK[:BASic]:DV:STA Syntax Te {<Boolean>} <x>...
Page 130 5.11 FFT Group :FFT<x>:MEASure:PEAK[:BASic]:FREQuen :FFT<x>:MEASure:PEAK[:BASic]:V<y>:VA cy<y>:VALue? Lue? Function Queries a peak frequency value for FFT analysis. Function Queries a peak value for FFT analysis. :FFT<x>:MEASure:PEAK[:BASic]:FREQuenc :FFT<x>:MEASure:PEAK[:BASic]:V<y>:VAL Syntax Syntax y<y>:VALue? <x> = 1 or 2 (1 only for 2-channel models) <x> = 1 or 2 (1 only for 2-channel models) <y>...
Page 131 5.11 FFT Group :FFT<x>:TYPE :FFT<x>:VERTical? Function Sets or queries the spectrum for FFT analysis. Function Queries all vertical axis settings for FFT analysis. :FFT<x>:TYPE {CH_MAG|CS_IMAG| :FFT<x>:VERTical? Syntax Syntax CS_LOGMAG|CS_MAG|CS_PHASE|CS_REAL| <x> = 1 or 2 (1 only for 2-channel models) LS_IMAG|LS_LOGMAG|LS_MAG|LS_PHASE| :FFT<x>:VERTical:LEVel LS_REAL|PS_LOGMAG|PS_MAG|PSD_LOGMAG| PSD_MAG|RS_LOGMAG|RS_MAG|TF_IMAG|...
Page 132 5.11 FFT Group :FFT<x>:WINDow Function Sets or queries the window function for FFT analysis. :FFT<x>:WINDow {FLATtop|HANNing| Syntax RECTangle} :FFT<x>:WINDow? <x> = 1 or 2 (1 only for 2-channel models) :FFT1:WINDOW FLATTOP Example :FFT1:WINDOW? -> :FFT1:WINDOW FLATTOP Index 5-99 IM 710105-17E...
Page 133: File Group
5.12 FILE Group :FILE? :FILE:DELete:{AHIStogram|ASCii|BI Nary|BMP|FFT|HLISt|JPEG|MEASure|P Function Queries all settings for data storage. NG|SBUS|SETup|SNAP|ZPOLygon|ZWAVe} :FILE? Syntax [:EXECute] :FILE:COPY:ABORt Function Deletes a specific type of data file. This is an Function Aborts file copying. overlap command. :FILE:COPY:ABORt :FILE:DELete:{AHIStogram|ASCii| Syntax Syntax :FILE:COPY:ABORT BINary|BMP|FFT|HLISt|JPEG|MEASure| Example PNG|SBUS|SETup|SNAP|ZPOLygon|ZWAVe}...
Page 134 5.12 FILE Group :FILE[:DIRectory]:PATH? :FILE:MOVE:DRIVe Function Queries the current directory. Function Sets the file move destination medium. :FILE[:DIRectory]:PATH? :FILE:MOVE:DRIVe {FLAShmem|USB,<NRf>} Syntax Syntax :FILE:DIRECTORY:PATH? Example <NRf> = 0 to 3 -> :FILE:DIRECTORY:PATH "PATH = :FILE:MOVE:DRIVE FLASHMEM Example FLASHMEM/UTIL" Description You can omit the <NRf> for USB if the drive is not partitioned or is not divided into LUNs.
Page 135 5.12 FILE Group :FILE:SAVE:{AHIStogram|ASCii|BINary| :FILE:SAVE:{ASCii|BINary}:HISTory FFT|HLISt|HARMonics|MEASure|SBUS|SET Function Sets or queries how history waveforms will be up|SNAP|ZWAVe}:ABORt saved. :FILE:SAVE:{ASCii|BINary}:HISTory {AL Function Aborts the saving of a specific type of data. Syntax :FILE:SAVE:{AHIStogram|ASCii|BINary|F L|AVERage|ONE} Syntax FT|HLISt|HARMonics|MEASure|SBUS|SETup :FILE:SAVE:{ASCii|BINary}:HISTory? |SNAP|ZWAVe}:ABORt Example (Below is an example for waveform data.) :FILE:SAVE:BINARY:HISTORY ALL Example (Below is an example for waveform data.)
Page 136 5.12 FILE Group :FILE:SAVE:ASCii:TINFormation (Time :FILE:SAVE:SBUS:COMPression Information) Function Sets or queries the save compression method of Function Sets or queries whether waveform data is saved SENT data. :FILE:SAVE:SBUS:COMPression {DECimati with time information (ON) or without it (OFF). Syntax :FILE:SAVE:ASCii:TINFormation {<Boole on|OFF|PTOPeak} Syntax an>}...
Page 137: Gonogo Group
5.13 GONogo Group :GONogo? :GONogo:ACTion:MAIL:MODE Function Queries all GO/NO-GO determination settings. Function Sets or queries whether or not the DLM2000 will :GONogo? Syntax send email notification for NO-GO results. :GONogo:ACTion:MAIL:MODE {<Boolean>} Syntax :GONogo:ABORt :GONogo:ACTion:MAIL:MODE? :GONOGO:ACTION:MAIL:MODE ON Function Aborts GO/NO-GO determination. Example :GONogo:ABORt :GONOGO:ACTION:MAIL:MODE?
Page 138 5.13 GONogo Group :GONogo:NGStopcount :GONogo[:ZPARameter]:NUMBer<x>:CAU Function Sets or queries the number of NO-GO results at which the DLM2000 will stop performing Function Queries whether or not the specified waveform determinations. parameter is the cause of a NO-GO zone or :GONogo:NGStopcount {<NRf>|UNFinity} Syntax parameter determination.
Page 139 5.13 GONogo Group :GONogo[:ZPARameter]:NUMBer<x>:PARam :GONogo[:ZPARameter]:NUMBer<x>:PARam eter:ITEM eter:TRACe Function Sets or queries the specified waveform Function Sets or queries the specified waveform parameter’s item for parameter determination. parameter’s source waveform for parameter :GONogo[:ZPARameter]:NUMBer<x>:PARame Syntax determination. ter:ITEM {<Parameter>} :GONogo[:ZPARameter]:NUMBer<x>:PARame Syntax :GONogo[:ZPARameter]:NUMBer<x>:PARame ter:TRACe {<NRf>|BIT<x>|FFT<x>|MATH<x ter:ITEM? >|XY<x>} :GONogo[:ZPARameter]:NUMBer<x>:PARame...
Page 140 5.13 GONogo Group :GONogo[:ZPARameter]:NUMBer<x>:POLYg :GONogo[:ZPARameter]:NUMBer<x>:POLYg on:HPOSition on:VPOSition Function Sets or queries the horizontal position that will be Function Sets or queries the vertical position that will be used for polygonal zone determination. used for polygonal zone determination. :GONogo[:ZPARameter]:NUMBer<x>:POLYgo :GONogo[:ZPARameter]:NUMBer<x>:POLYgo Syntax Syntax n:HPOSition {<NRf>} n:VPOSition {<NRf>}...
Page 141 5.13 GONogo Group :GONogo[:ZPARameter]:NUMBer<x>:RECTa :GONogo[:ZPARameter]:NUMBer<x>:RECTa ngle:HORizontal ngle:VERTical Function Sets or queries the horizontal position of the Function Sets or queries the vertical position of the rectangle that will be used for rectangular zone rectangle that will be used for rectangular zone determination.
Page 142 5.13 GONogo Group :GONogo[:ZPARameter]:NUMBer<x>:WAVE: :GONogo[:ZPARameter]:NUMBer<x>:WAVE: EDIT:PART TRACe Function Executes partial editing in waveform zone editing. Function Sets or queries the source waveform that will be :GONogo[:ZPARameter]:NUMBer<x>:WAVE:E Syntax used for waveform zone determination. DIT:PART {<NRF>,<NRF>,<NRF>,<NRF>} :GONogo[:ZPARameter]:NUMBer<x>:WAVE:T Syntax RACe {<NRf>|MATH<x>} <x> = 1 to 4 :GONogo[:ZPARameter]:NUMBer<x>:WAVE:T <NRF> = −...
Page 143: Hcopy Group
5.14 HCOPy Group :HCOPy? :HCOPy:EXTPrinter:TONE Function Queries all screen capture data output settings. Function Sets or queries the external printer output color :HCOPy? Syntax setting. :HCOPy:EXTPrinter:TONE {<Boolean>} Syntax :HCOPy:ABORt :HCOPy:EXTPrinter:TONE? :HCOPY:EXTPRINTER:TONE ON Function Stops data output and paper feeding. Example :HCOPy:ABORt :HCOPY:EXTPRINTER:TONE? Syntax...
Page 144 5.14 HCOPy Group :HCOPy:MULTitarget:FILE :HCOPy:PRINter? Function Sets or queries whether the multi target feature Function Queries all built-in printer output settings. :HCOPy:PRINter? will send output to a file. Syntax :HCOPy:MULTitarget:FILE {<Boolean>}:H Syntax :HCOPy:PRINter:MAG COPy:MULTitarget:FILE? :HCOPY:MULTITARGET:FILE ON:HCOPY:MULT Example Function Sets or queries the magnification used when the ITARGET:FILE? DLM2000 prints to the built-in printer in long copy ->...
Page 145 5.15 HISTory Group :HISTory? :HISTory:RECord? MINimum Function Queries all of the settings for the history feature. Function Queries the minimum history waveform record :HISTory? Syntax number. :HISTory:RECord? {MINimum} Syntax :HISTory:AVERage :HISTORY:RECORD? MINIMUM Example -> :HISTORY:RECORD −1 Function Sets or queries the highlight display mode for history waveforms.
Page 146: History Group
5.15 HISTory Group :HISTory[:SEARch]? :HISTory[:SEARch]:NUMBer<x>:MODE Function Queries all history waveform search settings. Function Sets or queries the search mode of a search :HISTory[:SEARch]? Syntax condition. :HISTory[:SEARch]:NUMBer<x>:MO Syntax :HISTory[:SEARch]:ABORt DE {PARameter|POLYgon|RECTangle| WAVE} Function Aborts searching. :HISTory[:SEARch]:ABORt :HISTory[:SEARch]:NUMBer<x>:MODE? Syntax :HISTORY:SEARCH:ABORT Example <x> = 1 to 4 :HISTORY:SEARCH:NUMBER1:MODE PARAMETE Example :HISTory[:SEARch]:EXECute...
Page 147 5.15 HISTory Group :HISTory[:SEARch]:NUMBer<x>:PARamete :HISTory[:SEARch]:NUMBer<x>:PARamete r:LIMit r:VALue? Function Sets or queries the specified waveform Function Queries the specified waveform parameter’s parameter’s upper and lower limits for parameter measured value for parameter searching. searching. :HISTory[:SEARch]:NUMBer<x>: Syntax :HISTory[:SEARch]:NUMBer<x>: Syntax PARameter:VALue? PARameter:LIMit {<NRf>} <x>...
Page 148 5.15 HISTory Group :HISTory[:SEARch]:NUMBer<x>:POLYgon: :HISTory[:SEARch]:NUMBer<x>:RECTang TRACe Function Sets or queries the source waveform that will be Function Queries all rectangular zone search settings. :HISTory[:SEARch]:NUMBer<x>:RECTang used for polygonal zone searching. Syntax :HISTory[:SEARch]:NUMBer<x>:POLYgon:T Syntax RACe {<NRf>|MATH<x>|XY<x>} <x> = 1 to 4 :HISTory[:SEARch]:NUMBer<x>:POLYgon:T :HISTory[:SEARch]:NUMBer<x>:RECTangl RACe? e:HORizontal...
Page 149 5.15 HISTory Group :HISTory[:SEARch]:NUMBer<x>:RECTangl :HISTory[:SEARch]:NUMBer<x>:WAVE:RAN e:TRACe Function Sets or queries the source waveform of the Function Sets or queries the source window that will be rectangle that will be used for rectangular zone used for waveform zone searching. :HISTory[:SEARch]:NUMBer<x>:WAVE:RAN searching. Syntax :HISTory[:SEARch]:NUMBer<x>: Ge {MAIN|Z1|Z2}...
Page 150 5.15 HISTory Group :HISTory[:SEARch]:NUMBer<x>:WAVE:ZNU :HISTory[:SEARch]:SIMPle:VERTical Mber Function Sets or queries the vertical position of the Function Sets or queries the zone number that will be used rectangle to use in simple searching. :HISTory[:SEARch]:SIMPle:VERTical {<N for waveform zone searching. Syntax :HISTory[:SEARch]:NUMBer<x>:WAVE:ZNUM Rf>,<NRf>} Syntax ber {<NRf>}...
Page 151: Image Group
5.16 IMAGe Group :IMAGe? :IMAGe:SAVE? Function Queries all screen image data output settings. Function Queries all file output settings. :IMAGe? Syntax :IMAGe:SAVE? Syntax :IMAGe:ABORt :IMAGe:SAVE:ANAMing Function Aborts saving screen image data to the storage Function Sets or queries the on/off status of the auto medium.
Page 152: Initialize Group
5.17 INITialize Group :INITialize:EXECute Function Executes initialization. :INITialize:EXECute Syntax :INITIALIZE:EXECUTE Example :INITialize:UNDO Function Undoes initialization. :INITialize:UNDO Syntax :INITIALIZE:UNDO Example Index 5-119 IM 710105-17E...
Page 153: Logic Group
5.18 LOGic Group You cannot use commands that relate to logic group on models that are not equipped with logic inputs. :LOGic[:PODA]:BIT<x>? :LOGic? Function Queries all of the settings for a bit of a specified Function Queries all logic input waveform settings. logic input pod.
Page 154 5.18 LOGic Group :LOGic[:PODA]:DESKew :LOGic:GROup:STATe? Function Sets or queries the deskewing of a specified logic Function Queries all logic-input state display settings. :LOGic:GROup:STATe? input pod. Syntax :LOGic[:PODA]:DESKew {<Time>} Syntax :LOGic:GROup:STATe:CLOCk :LOGic[:PODA]:DESKew? <Time> = −100 to 100 ns (in 10-ps steps) Function Sets or queries the reference clock waveform of :LOGIC:PODA:DESKEW 1NS Example the logic-input state display.
Page 155 5.18 LOGic Group :LOGic:GROup:STATe:THReshold Function Sets or queries the detection level of the reference clock waveform of the logic-input state display. :LOGic:GROup:STATe:THReshold {<NRf>} Syntax :LOGic:GROup:STATe:THReshold? <NRf> = See the DLM2000 Features Guide for this information. :LOGIC:GROUP:STATE:THRESHOLD 1 Example :LOGIC:GROUP:STATE:THRESHOLD? -> :LOGIC:GROUP:STATE:THRESHOLD 1.000 E+00 :LOGic:POSition Function...
Page 156: Math Group
5.19 MATH Group User-defined computation is an option available only for 4-channel models. User-defined computation commands cannot be used on 2-channel models or 4-channel models without the user-defined computation option. :MATH<x>? :MATH<x>:ECOunt:THReshold Function Queries all computation settings. Function Sets or queries the edge detection level for edge- :MATH<x>? Syntax count computation.
Page 157 5.19 MATH Group :MATH<x>:FILTer:TIME :MATH<x>:LABel[:DEFine] Function Sets or queries a phase shift delay time. Function Sets or queries a computed waveform label. :MATH<x>:FILTer:TIME {<Time>} :MATH<x>:LABel[:DEFine] {<String>} Syntax Syntax :MATH<x>:FILTer:TIME? :MATH<x>:LABel[:DEFine]? <x> = 1 or 2 (1 only for 2-channel models) <x>...
Page 158 5.19 MATH Group :MATH<x>:RCOunt:THReshold<y> :MATH<x>:UNIT? Function Sets or queries the threshold level for rotary-count Function Queries all computation unit settings. :MATH<x>:UNIT? computation. Syntax :MATH<x>:RCOunt:THReshold<y> {<NRf>| Syntax <x> = 1 or 2 (1 only for 2-channel models) <Voltage>|<Current>} :MATH<x>:UNIT[:DEFine] :MATH<x>:RCOunt:THReshold<y>? <x> = 1 or 2 (1 only for 2-channel models) Function Sets or queries a unit of computation.
Page 159 5.19 MATH Group :MATH<x>:USERdefine:AVERage:EWEight :MATH<x>:USERdefine:DEFine Function Sets or queries the attenuation constant Function Sets or queries the equation for user-defined of exponential averaging in user-defined computation. :MATH<x>:USERdefine:DEFine {<String>} computation. Syntax :MATH<x>:USERdefine:AVERage:EWEig :MATH<x>:USERdefine:DEFine? Syntax ht {<NRf>} <x> = 1 or 2 (1 only for 2-channel models) :MATH<x>:USERdefine:AVERage:EWEight? <String>...
Page 160 5.19 MATH Group :MATH<x>:USERdefine:FILTer<y>:TYPE :MATH<x>:USERdefine:SCALe:CENTer Function Sets or queries the filter type for user-defined Function Sets or queries the center value for scaling in computation. user-defined computation. :MATH<x>:USERdefine:FILTer<y>:TY :MATH<x>:USERdefine:SCALe:CENT Syntax Syntax PE {IIR|FIR} er {<NRf>} :MATH<x>:USERdefine:FILTer<y>:TYPE? :MATH<x>:USERdefine:SCALe:CENTer? <x> = 1 or 2 (1 only for 2-channel models) <x>...
Page 161: Measure Group
5.20 MEASure Group You cannot use commands that relate to logic waveforms on models that are not equipped with logic inputs. :MEASure? :MEASure:BIT<x>:AREA2:<Parameter>:CO UNt? Function Queries all of the settings for automated Function Queries the statistical processing count of a logic measurement of waveform parameters.
Page 162 5.20 MEASure Group :MEASure:BIT<x>:AREA2:<Parameter>:VA :MEASure:BIT<x>:AREA2:DELay:MEASure: COUNt Lue? Function Sets or queries the count number of a source Function Queries an automatically measured value of a waveform for measuring the delay between logic waveform parameter in Area2. channels of a logic waveform in Area2. :MEASure:BIT<x>:AREA2:<Parameter>:VAL Syntax :MEASure:BIT<x>:AREA2:DELay:MEASure:C...
Page 163 5.20 MEASure Group :MEASure:BIT<x>:AREA2:DELay:REFerenc :MEASure:BIT<x>:AREA2:DELay:REFerenc e:COUNt e:TRACe Function Sets or queries the edge count of the reference Function Sets or queries the reference waveform edge used waveform used to measure the delay between to measure the delay between the specified logic the specified logic waveform and the reference waveform and the reference waveform in Area2.
Page 164 5.20 MEASure Group :MEASure:BIT<x>:<Parameter>:{MAXimum :MEASure:BIT<x>:<Parameter>:VALue? |MEAN|MINimum|SDEViation}? Function Queries an automatically measured value of a Function Queries a statistical value of a logic waveform logic waveform parameter. :MEASure:BIT<x>:<Parameter>:VALue? [{ parameter. Syntax :MEASure:BIT<x>:<Parameter>:{MAXimum| NRf}] Syntax MEAN|MINimum|SDEViation}? <x> = 1 to 8 <Parameter> = { AVGFreq|DELay|DUTYcycle| <x>...
Page 165 5.20 MEASure Group :MEASure:BIT<x>:DELay:MEASure:COUNt :MEASure:BIT<x>:DELay:REFerence:SLO Function Sets or queries the count number of a source waveform for measuring the delay between Function Sets or queries the slope of the reference waveform channels of a logic waveform. used to measure the delay between the specified :MEASure:BIT<x>:DELay:MEASure:COU Syntax logic waveform and the reference waveform.
Page 166 5.20 MEASure Group :MEASure:BIT<x>:DELay:STATe :MEASure:{CHANnel<x>|MATH<x>}:AREA2: <Parameter>? Function Sets or queries the on/off status and the display format of a delay parameter. Function Queries the setting of a waveform parameter of a :MEASure:BIT<x>:DELay:STATe {OFF|ON| Syntax waveform in Area2. DEGRee} :MEASure:{CHANnel<x>|MATH<x>}:AREA2:< Syntax :MEASure:BIT<x>:DELay:STATe? Parameter>? <x>...
Page 167 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:AREA2: :MEASure:{CHANnel<x>|MATH<x>}:AREA2: <Parameter>:{MAXimum|MEAN|MINimum|SD <Parameter>:VALue? EViation}? Function Queries an automatically measured value of a Function Queries a statistical value of a waveform waveform parameter in Area2. :MEASure:{CHANnel<x>|MATH<x>}:AREA2:< parameter in Area2. Syntax :MEASure:{CHANnel<x>|MATH<x>}:AREA2:< Parameter>:VALue? [<NRf>[,STATus]] Syntax Parameter>:{MAXimum|MEAN|MINimum|SDEV :MEASure:{CHANnel<x>|MATH<x>}:AREA2:< iation}? Parameter>:VALue? [STATus] <x>...
Page 168 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:AREA2: :MEASure:{CHANnel<x>|MATH<x>}:AREA2: COPY DELay:MEASure:COUNt Function Copies the on/off status of all measurement items Function Sets or queries the count number of a source of a waveform in Area2 to all other waveforms. waveform for measuring the delay between :MEASure:{CHANnel<x>|MATH<x>}:AREA2:C Syntax channels of a waveform in Area2.
Page 169 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:AREA2: :MEASure:{CHANnel<x>|MATH<x>}:AREA2: DELay:REFerence:COUNt DELay:REFerence:SOURce Function Sets or queries the edge count of the reference Function Sets or queries whether the reference point for waveform used to measure the delay between the measuring the delay between channels of a specified waveform and the reference waveform in waveform in Area2 will be set to the trigger point Area2.
Page 170 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:AREA2: :MEASure:{CHANnel<x>|MATH<x>}:<Param DELay:STATe eter>:COUNt? Function Sets or queries the on/off status and the display Function Queries the statistical processing count of a format of a delay parameter in Area2. waveform parameter. :MEASure:{CHANnel<x>|MATH<x>}:AREA2:D :MEASure:{CHANnel<x>|MATH<x>}:<Parame Syntax Syntax ELay:STATe {OFF|ON|DEGRee} ter>:COUNt? :MEASure:{CHANnel<x>|MATH<x>}:AREA2:D <x>...
Page 171 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:<Param Description• If the value is immeasurable, the DLM2000 eter>:STATe returns “NAN” (not a number). Function Sets or queries the on/off status of a waveform • The <NRf> is used to specify which iteration of parameter. automated measurement to query the measured :MEASure:{CHANnel<x>|MATH<x>}:<Parame Syntax value from.
Page 172 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:DELay? :MEASure:{CHANnel<x>|MATH<x>}:DELay: MEASure:SLOPe Function Queries all of the settings for measuring the delay between channels of a waveform. Function Sets or queries a source waveform slope that will :MEASure:{CHANnel<x>|MATH<x>}:DELay? Syntax be used to measure delay between channels. :MEASure:{CHANnel<x>|MATH<x>}:DELay:M <x>...
Page 173 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:DELay: :MEASure:{CHANnel<x>|MATH<x>}:DELay: STATe REFerence:SLOPe Function Sets or queries the on/off status and the display Function Sets or queries the slope of the reference format of a delay parameter. waveform used to measure the delay between the :MEASure:{CHANnel<x>|MATH<x>}:DELay:S Syntax specified waveform and the reference waveform.
Page 174 5.20 MEASure Group :MEASure:{CHANnel<x>|MATH<x>}:DPRoxi :MEASure:CONTinuous? mal:PERCent Function Queries all settings for the normal statistical Function Sets or queries the distal, mesial, and proximal processing of automatically measured waveform points as percentages. parameters. :MEASure:{CHANnel<x>|MATH<x>}:DPRoxim :MEASure:CONTinuous? Syntax Syntax al:PERCent {<NRf>,<NRf>,<NRf>} :MEASure:CONTinuous:RESTart :MEASure:{CHANnel<x>|MATH<x>}:DPRoxim al:PERCent? Function Restarts the normal statistical processing of the...
Page 175 5.20 MEASure Group :MEASure:HISTory:ABORt :MEASure:TRANge<x> (Time Range) Function Aborts statistical processing of automatically Function Sets or queries a time range. :MEASure:TRANge<x> {<NRf>,<NRf>} measured history waveforms. Syntax :MEASure:HISTory:ABORt :MEASure:TRANge<x>? Syntax :MEASURE:HISTORY:ABORT Example <x> = 1 or 2 <NRf> = −5 to 5 divisions (in steps of 10 divisions/ :MEASure:HISTory:EXECute display record length) :MEASURE:TRANGE1 −4,4 Function Executes statistical processing of automatically...
Page 176 5.20 MEASure Group :MEASure:USER<X>:NAME :MEASure:WAIT? Function Sets or queries the name of a Calc item. Function Waits for the completion of waveform parameter :MEASure:USER<X>:NAME {<String>}:MEAS Syntax automated measurement with a set timeout. ure:USER<X>:NAME? :MEASure:WAIT? {<NRf>} Syntax <x> = 1 to 4 <NRf>...
Page 177: Recall Group
5.21 RECall Group :RECall:SETup<x>:EXECute Function Recalls setup data from an internal memory area. :RECall:SETup<x>:EXECute Syntax <x> = 1 to 3 :RECALL:SETUP1:EXECUTE Example Description If you specify an area that does not contain setup data, an error occurs. 5-144 IM 710105-17E...
Page 178: Reference Group
5.22 REFerence Group :REFerence<x>? :REFerence<x>:POSition Function Queries all reference waveform settings. Function Sets or queries the vertical position of a reference :REFerence<x>? Syntax waveform. :REFerence<x>:POSition {<NRf>} <x> = 1 or 2 (1 only for 2-channel models) Syntax :REFerence<x>:POSition? :REFerence<x>:DISPlay <x> = 1 or 2 (1 only for 2-channel models) Function Sets or queries the display on/off status of a <NRf> = −4 to 4 (divisions)
Page 179: Search Group
5.23 SEARch Group The following table indicates how the communication commands for searching correspond to the menu items that appear on the screen. Search Type Communication Setup Menu Command Search Menu Search Type Edge search EDGE SEARCH Edge Edge qualified search QUALify Edge Qualified State search...
Page 180 5.23 SEARch Group :SEARch:EDGE:SOURce :SEARch:POSition<x> Function Sets or queries the edge search source waveform. Function Sets or queries the position of a zoom box. :SEARch:EDGE:SOURce {<NRf>|BIT<x>| :SEARch:POSition<x> {<NRf>} Syntax Syntax MATH<x>} :SEARch:POSition<x>? :SEARch:EDGE:SOURce? <x> = 1 or 2 <NRf> = 1 to 4 (1 or 2 for 2-channel models) <NRf> = −5 to 5 divisions (in steps of 10 divisions/ <x>...
Page 181 5.23 SEARch Group :SEARch:PPATtern:{CHANnel<x>|MATH<x> :SEARch:PPATtern:{CHANnel<x>|MATH<x> }:PATTern }:HYSTeresis Function Sets or queries a source waveform search pattern Function Sets or queries a source waveform hysteresis for for state or state width searching. state or state width searching. :SEARch:PPATtern:{CHANnel<x>|MATH<x> Syntax :SEARch:PPATtern:{CHANnel<x>| Syntax }:PATTern {DONTcare|HIGH|LOW} MATH<x>}:HYSTeresis {<NRf>} :SEARch:PPATtern:{CHANnel<x>|MATH<x>...
Page 182 5.23 SEARch Group :SEARch:PPATtern:CLOCk:SLOPe :SEARch:PPATtern:TIME<x> Function Sets or queries the clock channel slope for state Function Sets or queries the pulse width setting for state or or state width searching. state width searching. :SEARch:PPATtern:CLOCk:SLOPe {FALL|RI :SEARch:PPATtern:TIME<x> {<Time>} Syntax Syntax :SEARch:PPATtern:TIME<x>? :SEARch:PPATtern:CLOCk:SLOPe? <x>...
Page 183 5.23 SEARch Group :SEARch:SELect? MAXimum :SEARch:TWINdow Function Queries the number of detected points. Function Sets or queries which window will display the :SEARch:SELect? {MAXimum} Syntax detected points. :SEARCH:SELECT? MAXIMUM :SEARch:TWINdow {Z1|Z2} Example Syntax -> :SEARCH:SELECT 100 :SEARch:TWINdow? :SEARCH:TWINDOW Z1 Description If there are no detected points, the DLM2000 Example :SEARCH:TWINDOW? returns “NAN.”...
Page 184 5.23 SEARch Group :SEARch:WIDTh:SOURce Function Sets or queries the pulse width search source waveform. :SEARch:WIDTh:SOURce {<NRf>|BIT<x>| Syntax MATH<x>|NONE} :SEARch:WIDTh:SOURce? <NRf> = 1 to 4 (1 or 2 for 2-channel models) <x> of BIT<x> = 1 to 8 <x> of MATH<x> = 1 or 2 (1 only for 2-channel models) :SEARCH:WIDTH:SOURCE 1 Example...
Page 185: Serialbus Group
5.24 SERialbus Group The following table indicates how the communication commands for serial bus types correspond to the menu items that appear on the screen. Serial Bus Type Communication Setup Menu Command Serial Bus Menu Serial Bus Type CAN bus signal CAN* SERIAL BUS CAN FD bus signal...
Page 186 5.24 SERialbus Group :SERialbus<x>:CAN[:ANALyze]:SETup:SO :SERialbus<x>:CAN:DETail:LIST:ITEM? URce Function Queries all items that will be displayed in the CAN Function Sets or queries the CAN bus signal analysis bus signal analysis result list. :SERialbus<x>:CAN:DETail:LIST:ITEM? source. Syntax :SERialbus<x>:CAN[:ANALyze]:SETup:SOU Syntax <x> = 1 to 4 Rce {<NRf>|MATH<x>} :SERIALBUS1:CAN:DETAIL:LIST:ITEM? Example...
Page 187 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:FJUMp:CRC :SERialbus<x>:CAN:SEARch:SELect? MAXimum Function Jumps to the CRC Field in the CAN bus signal search result. Function Queries the number of detected points in the CAN :SERialbus<x>:CAN:SEARch:FJUMp:CRC Syntax bus signal search. :SERialbus<x>:CAN:SEARch:SELe <x> = 1 to 4 Syntax :SERIALBUS1:CAN:SEARCH:FJUMP:CRC ct? {MAXimum}...
Page 188 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:SETup:EFRam :SERialbus<x>:CAN:SEARch:SETup[:IDDa e:CRC ta]:ACK:MODE Function Sets or queries the CAN bus signal search CRC Function Sets or queries the ACK mode, which is one of error setting. the ID and data conditions, for CAN bus signal :SERialbus<x>:CAN:SEARch:SETup: Syntax searching.
Page 189 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:SETup[:IDDa :SERialbus<x>:CAN:SEARch:SETup[:IDDa ta]:DATA:DECimal<y> ta]:DATA:HEXa<y> Function Sets a reference value, which is one of the ID and Function Sets a reference value, which is one of the ID and data conditions, for CAN bus signal searching in data conditions, for CAN bus signal searching in decimal notation.
Page 190 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:SETup[:IDDa :SERialbus<x>:CAN:SEARch:SETup[:IDDa ta]:IDENtifier:HEXa ta]:DATA:PATTern<y> Function Sets the ID value, which is one of the ID and Function Sets or queries the data value, which is one of data conditions, for CAN bus signal searching in the ID and data conditions, for CAN bus signal hexadecimal notation.
Page 191 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:SETup[:IDDa :SERialbus<x>:CAN:SEARch:SETup[:IDDa ta]:IDENtifier:PATTern ta]:MSIGnal:SELect Function Sets or queries the ID pattern, which is one of Function Sets or queries the message and signal condition, the ID and data conditions, for CAN bus signal which is one of the ID and data conditions, for searching in binary notation.
Page 192 5.24 SERialbus Group :SERialbus<x>:CAN:SEARch:SETup[:IDDa :SERialbus<x>:CAN:SEARch:SETup:MODE ta]:MSIGnal:SIGNal:DECimal<y> Function Sets or queries the CAN bus signal search mode Function Sets a signal’s reference value, which is one of setting. :SERialbus<x>:CAN:SEARch:SETup:MO the ID and data conditions, for CAN bus signal Syntax DE {EFRame|IDData|SOF} searching in decimal notation.
Page 193 5.24 SERialbus Group :SERialbus<x>:CANFD[:ANALyze]:SETup: :SERialbus<x>:CANFD[:ANALyze]:SETup: DBRate RECessive Function Sets or queries the CAN FD bus signal analysis Function Sets or queries the CAN FD bus signal analysis data bit rate (data transfer rate of data phase). recessive level. :SERialbus<x>:CANFD[:ANALyze]:SETup:D :SERialbus<x>:CANFD[:ANALyze]:SETup:R Syntax Syntax BRate {<NRf>|USER,<NRf>}...
Page 194 5.24 SERialbus Group :SERialbus<x>:CANFD:DETail? :SERialbus<x>:CANFD:SEARch:EXECute Function Queries all CAN FD bus signal analysis result list Function Executes a CAN FD bus signal search. :SERialbus<x>:CANFD:SEARch:EXECute settings. Syntax :SERialbus<x>:CANFD:DETail? Syntax <x> = 1 to 4 :SERIALBUS1:CANFD:SEARCH:EXECUTE <x> = 1 to 4 Example :SERialbus<x>:CANFD:DETail:DISPlay :SERialbus<x>:CANFD:SEARch:FJUMp:ACK Function...
Page 195 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SELect :SERialbus<x>:CANFD:SEARch:SETup:EFR ame:CRCEFactor? Function Sets which detected point to display in the CAN FD bus signal search zoom window and queries Function Queries all CRC error factor settings for CAN FD the zoom position of the detected point. bus signal searching.
Page 196 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SETup:EFR :SERialbus<x>:CANFD:SEARch:SETup[:ID ame[:MODE] Data]:ACK? Function Sets or queries the CAN FD bus signal search Function Queries all ACK settings for the ID and data error frame setting. conditions for CAN FD bus signal searching. :SERialbus<x>:CANFD:SEARch:SETup:EFRa :SERialbus<x>:CANFD:SEARch:SETup[:IDD Syntax Syntax me[:MODE] {<Boolean>} ata]:ACK?
Page 197 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SETup[:ID :SERialbus<x>:CANFD:SEARch:SETup[:ID Data]:DATA:BCOunt Data]:DATA:DECimal<y> Function Sets or queries the pattern comparison position, Function Sets a reference value, which is one of the ID and which is one of the ID and data conditions, for data conditions, for CAN FD bus signal searching CAN FD bus signal searching.
Page 198 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SETup[:ID :SERialbus<x>:CANFD:SEARch:SETup[:ID Data]:DATA:MODE Data]:DATA:PFORmat Function Sets or queries the data enable/disable condition, Function Sets or queries the data input format, which is one which is one of the ID and data conditions, for of the ID and data conditions, for CAN FD bus CAN FD bus signal searching.
Page 199 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SETup[:ID :SERialbus<x>:CANFD:SEARch:SETup[:ID Data]:IDENtifier:MFORmat Data]:IDENtifier:PFORmat Function Sets or queries the ID frame format (standard Function Sets or queries the ID input format, which is one of or extended), which is one of the ID and data the ID and data conditions, for CAN FD bus signal conditions, for CAN FD bus signal searching.
Page 200 5.24 SERialbus Group :SERialbus<x>:CANFD:SEARch:SETup[:ID :SERialbus<x>:CANFD:SEARch:SETup[:ID Data]:MSIGnal:SIGNal? Data]:MSIGnal:SIGNal:ITEM Function Queries all signal settings for the ID and data Function Sets the signal item, which is one of the ID and conditions for CAN FD bus signal searching. data conditions, for CAN FD bus signal searching. :SERialbus<x>:CANFD:SEARch:SETup[:IDD :SERialbus<x>:CANFD:SEARch:SET Syntax...
Page 201 5.24 SERialbus Group :SERialbus<x>:DECode[:FORMat] :SERialbus<x>:FLEXray[:ANALyze]:SETu p:BCHannel Function Sets or queries the decode display format of serial bus signals. Function Sets or queries the channel bus type for FLEXRAY :SERialbus<x>:DECode[:FORMat] {BINary Syntax bus signal analysis. |HEXa|ASCii|SYMBol} :SERialbus<x>:FLEXray[:ANALyze]: Syntax :SERialbus<x>:DECode[:FORMat]? SETup:BCHannel {A|B} :SERialbus<x>:FLEXray[:ANALyze]: <x>...
Page 202 5.24 SERialbus Group :SERialbus<x>:FLEXray[:ANALyze]:SETu :SERialbus<x>:FLEXray:DETail:LIST:VA p:SPOint Lue? Function Sets or queries the FLEXRAY bus signal sample Function Queries all of the data for the specified analysis point. number in the FLEXRAY bus signal analysis result :SERialbus<x>:FLEXray[:ANALyze]: Syntax list. SETup:SPOint {<NRf>} :SERialbus<x>:FLEXray:DETail:LIST:VAL Syntax :SERialbus<x>:FLEXray[:ANALyze]:...
Page 203 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:FJUMp:F :SERialbus<x>:FLEXray:SEARch:SETup:E RAMeid RRor:BSS Function Jumps to the frame ID field in the FLEXRAY bus Function Sets or queries the FLEXRAY bus signal search signal analysis results. BSS error setting. :SERialbus<x>:FLEXray:SEARch:FJUMp:FR :SERialbus<x>:FLEXray:SEARch:SETup:ER Syntax Syntax AMeid Ror:BSS {<Boolean>} :SERialbus<x>:FLEXray:SEARch:SETup:ER <x>...
Page 204 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:SETup:E :SERialbus<x>:FLEXray:SEARch:SETup[: RRor:HCRC IDData]:CCOunt:COUNt<y> Function Sets or queries the FLEXRAY bus signal search Function Sets or queries a FLEXRAY bus signal-search Header CRC error setting. cycle-count setting. :SERialbus<x>:FLEXray:SEARch:SETup:ER :SERialbus<x>:FLEXray:SEARch:SETup[:I Syntax Syntax Ror:HCRC {<Boolean>} DData]:CCOunt:COUNt<y> {<NRf>} :SERialbus<x>:FLEXray:SEARch:SETup:ER :SERialbus<x>:FLEXray:SEARch:SETup[:I Ror:HCRC? DData]:CCOunt:COUNt<y>? <x>...
Page 205 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:SETup[: :SERialbus<x>:FLEXray:SEARch:SETup[: IDData]:DATA:BCOunt IDData]:DATA:DECimal<y> Function Sets or queries the position for comparing Function Sets or queries a reference value, which is one data patterns, which is one of the ID and data of the ID and data conditions, for FLEXRAY bus conditions, for FLEXRAY bus signal searching.
Page 206 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:SETup[: :SERialbus<x>:FLEXray:SEARch:SETup[: IDData]:DATA:MODE IDData]:DATA:PFORmat Function Sets or queries the data enable/disable condition, Function Sets or queries the data input format, which is one which is one of the ID and data conditions, for of the ID and data conditions, for FLEXRAY bus FLEXRAY bus signal searching.
Page 207 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:SETup[: :SERialbus<x>:FLEXray:SEARch:SETup[: IDData]:FID:CONDition IDData]:INDIcator? Function Sets or queries the frame ID data condition, which Function Queries all indicator settings for the ID and data is one of the ID and data conditions, for FLEXRAY conditions for FLEXRAY bus signal searching. :SERialbus<x>:FLEXray:SEARch:SETup[:I bus signal searching.
Page 208 5.24 SERialbus Group :SERialbus<x>:FLEXray:SEARch:SETup[: :SERialbus<x>:I2C[:ANALyze]? IDData]:INDIcator:STFRame Function Queries all I C bus signal analysis settings. :SERialbus<x>:I2C[:ANALyze]? Function Sets or queries whether or not the indicator start Syntax frame, which is one of the ID and data conditions, <x> = 1 to 4 for FLEXRAY bus signal searching.
Page 209 5.24 SERialbus Group :SERialbus<x>:I2C:DETail? :SERialbus<x>:I2C:SEARch? Function Queries all I C bus signal analysis result list Function Queries all I C bus signal search settings. :SERialbus<x>:I2C:SEARch? settings. Syntax :SERialbus<x>:I2C:DETail? Syntax <x> = 1 to 4 <x> = 1 to 4 :SERialbus<x>:I2C:SEARch:ABORt :SERialbus<x>:I2C:DETail:DISPlay Function Aborts the I...
Page 210 5.24 SERialbus Group :SERialbus<x>:I2C:SEARch[:SETup]:ADD :SERialbus<x>:I2C:SEARch[:SETup]:ADD Ress? Ress:ADDRess[:BIT7ADdress]? Function Queries all address pattern settings for I C bus Function Queries all 7-bit address settings for I C bus signal signal searching. searching. :SERialbus<x>:I2C:SEARch[:SETup]:ADDR :SERialbus<x>:I2C:SEARch[:SETup]:ADDR Syntax Syntax ess? ess:ADDRess[:BIT7ADdress]? <x> = 1 to 4 <x>...
Page 211 5.24 SERialbus Group :SERialbus<x>:I2C:SEARch[:SETup]:ADD :SERialbus<x>:I2C:SEARch[:SETup]:ADD Ress:ADDRess:BIT7APsub:ADDRess:HEXa Ress:ADDRess:BIT7APsub:SADDress:PATT Function Sets the 7-bit address for the 7-bit + sub address for I C bus signal searching in hexadecimal Function Sets or queries the sub address for the 7-bit + notation. sub address for I C bus signal searching in binary :SERialbus<x>:I2C:SEARch[:SETup]:AD Syntax...
Page 212 5.24 SERialbus Group :SERialbus<x>:I2C:SEARch[:SETup]:ADD :SERialbus<x>:I2C:SEARch[:SETup]:ADD Ress:DATA:CONDition Ress:ADDRess:TYPE Function Sets or queries the data comparison condition (true Function Sets or queries the address type, which is one or false) for I C bus signal searching. of the address conditions, for I C bus signal :SERialbus<x>:I2C:SEARch[:SETup]:ADDR Syntax...
Page 213 5.24 SERialbus Group :SERialbus<x>:I2C:SEARch[:SETup]:ADD :SERialbus<x>:I2C:SEARch:SETup:GENer alcall:BIT7Maddress? Ress:DATA:PATTern<y> Function Queries all general call’s 7-bit master address Function Sets or queries the data value, which is one of the settings for I C bus signal searching. data conditions, for I C bus signal searching in :SERialbus<x>:I2C:SEARch:SETup:GENera Syntax binary notation.
Page 214 5.24 SERialbus Group :SERialbus<x>:I2C:SEARch:SETup:MODE :SERialbus<x>:I2C:SEARch:SETup:NONac k:STARtbyte Function Sets or queries the I C bus signal search type. :SERialbus<x>:I2C:SEARch:SETup:MO Syntax Function Sets or queries whether or not NON ACK will be DE {ADRData|EVERystart|GENeralcall|HS ignored in start bytes for I C bus signal searching. Mode|NONack|STARtbyte} :SERialbus<x>:I2C:SEARch:SETup: Syntax...
Page 215 5.24 SERialbus Group :SERialbus<x>:LIN[:ANALyze]:SETup:RE :SERialbus<x>:LIN:DETail? Vision Function Queries all LIN bus signal analysis result list Function Sets or queries the LIN bus signal analysis settings. :SERialbus<x>:LIN:DETail? revision number. Syntax :SERialbus<x>:LIN[:ANALyze]:SETup:REV Syntax <x> = 1 to 4 ision {BOTH|LIN1_3|LIN2_0} :SERialbus<x>:LIN:DETail:DISPlay :SERialbus<x>:LIN[:ANALyze]:SETup:REV ision? Function Sets or queries the display mode for the LIN bus...
Page 216 5.24 SERialbus Group :SERialbus<x>:LIN:SEARch:EXECute :SERialbus<x>:LIN:SEARch:SELect Function Executes a LIN bus signal search. Function Sets which detected point to display in the LIN bus :SERialbus<x>:LIN:SEARch:EXECute Syntax signal search zoom window and queries the zoom <x> = 1 to 4 position of the detected point. :SERIALBUS1:LIN:SEARCH:EXECUTE :SERialbus<x>:LIN:SEARch:SELect {<NRf Example...
Page 217 5.24 SERialbus Group :SERialbus<x>:LIN:SEARch:SETup:ERRor :SERialbus<x>:LIN:SEARch:SETup:ERRor :FRAMing :TIMeout Function Sets or queries the LIN bus signal search framing Function Sets or queries the LIN bus signal search timeout error setting. error setting. :SERialbus<x>:LIN:SEARch:SETup:ERRor: :SERialbus<x>:LIN:SEARch:SETup:ERRor: Syntax Syntax FRAMing {<Boolean>} TIMeout {<Boolean>} :SERialbus<x>:LIN:SEARch:SETup:ERRor: :SERialbus<x>:LIN:SEARch:SETup:ERRor: FRAMing? TIMeout?
Page 218 5.24 SERialbus Group :SERialbus<x>:LIN:SEARch:SETup:IDDat :SERialbus<x>:LIN:SEARch:SETup:IDDat a:DATA:DBYTe a:DATA:HEXa<y> Function Sets or queries the number of data bytes for LIN Function Sets the data for LIN bus signal searching in bus signal searching. hexadecimal notation. :SERialbus<x>:LIN:SEARch:SETup: :SERialbus<x>:LIN:SEARch:SETup:IDData Syntax Syntax IDData:DATA:DBYTe {<NRf>} :DATA:HEXa<y> {<String>} :SERialbus<x>:LIN:SEARch:SETup: <x>...
Page 219 5.24 SERialbus Group :SERialbus<x>:LIN:SEARch:SETup:IDDat :SERialbus<x>:LIN:SEARch:SETup:IDDat a:DATA:PATTern<y> a:IDENtifier:ID? Function Sets or queries the data value for LIN bus signal Function Queries all LIN bus signal search ID settings. :SERialbus<x>:LIN:SEARch:SETup:IDData searching in binary notation. Syntax :SERialbus<x>:LIN:SEARch:SETup:IDData :IDENtifier:ID? Syntax :DATA:PATTern<y> {<String>} <x> = 1 to 4 :SERialbus<x>:LIN:SEARch:SETup:IDData :SERialbus<x>:LIN:SEARch:SETup:IDDat :DATA:PATTern<y>?
Page 220 5.24 SERialbus Group :SERialbus<x>:LIN:SEARch:SETup:IDDat :SERialbus<x>:PSI5[:ANALyze]:SETup:D a:IDENtifier:PFORmat ATA:BRATe Function Sets or queries the ID input format for LIN bus Function Sets or queries the PSI5 signal analysis bit rate signal searching. (data transfer rate). :SERialbus<x>:LIN:SEARch:SETup: :SERialbus<x>:PSI5[:ANALyze]:SETup:DA Syntax Syntax IDData:IDENtifier:PFORmat {BINary|HEX TA:BRATe {<NRf>|USER,<NRf>} :SERialbus<x>:PSI5[:ANALyze]:SETup:DA :SERialbus<x>:LIN:SEARch:SETup: TA:BRATe?
Page 221 5.24 SERialbus Group :SERialbus<x>:PSI5[:ANALyze]:SETup:D :SERialbus<x>:PSI5[:ANALyze]:SETup:D ATA:EDETection ATA:SOURce Function Sets or queries the error detection method for Function Sets or queries the data source for PSI5 signal PSI5 signal analysis. analysis. :SERialbus<x>:PSI5[:ANALyze]:SETup:DA :SERialbus<x>:PSI5[:ANALyze]:SETup:DA Syntax Syntax TA:EDETection {CRC|PARity} TA:SOURce {<NRf>|MATH<y>} :SERialbus<x>:PSI5[:ANALyze]:SETup:DA :SERialbus<x>:PSI5[:ANALyze]:SETup:DA TA:EDETection? TA:SOURce? <x>...
Page 222 5.24 SERialbus Group :SERialbus<x>:PSI5[:ANALyze]:SETup:S :SERialbus<x>:PSI5:DETail:LIST:ALL? LOT<y> Function Queries all the data for all analysis numbers in the Function Sets or queries the slot’s start and end times for PSI5 signal analysis result list. :SERialbus<x>:PSI5:DETail:LIST:ALL? PSI5 signal analysis. Syntax :SERialbus<x>:PSI5[:ANALyze]:SETup:SL Syntax <x>...
Page 223 5.24 SERialbus Group :SERialbus<x>:PSI5:SEARch:SELect :SERialbus<x>:PSI5:SEARch:SETup:DATA :DATA:DECimal<y> Function Sets which detected point to display in the PSI5 signal search zoom window and queries the zoom Function Sets or queries the data of the PSI5 signal data position of the detected point. search in decimal notation.
Page 224 5.24 SERialbus Group :SERialbus<x>:PSI5:SEARch:SETup:DATA :SERialbus<x>:PSI5:SEARch:SETup:ERR :DATA:PFORmat Function Sets or queries the data input format of the PSI5 Function Queries all PSI5 signal error search settings. :SERialbus<x>:PSI5:SEARch:SETup:ERR signal data search in binary notation. Syntax :SERialbus<x>:PSI5:SEARch:SETup: Syntax DATA:DATA:PFORmat {BINary|HEXa} <x> = 1 to 4 :SERialbus<x>:PSI5:SEARch:SETup: :SERialbus<x>:PSI5:SEARch:SETup:ERRo DATA:DATA:PFORmat?
Page 225 5.24 SERialbus Group :SERialbus<x>:PSI5:SEARch:SETup:ERRo :SERialbus<x>:PSI5:SEARch:SETup:FRAM r:PCRC einslot:SNUMber Function Sets or queries the PSI5 signal parity/CRC error Function Sets or queries the slot number of the PSI5 signal search. slot specification search. :SERialbus<x>:PSI5:SEARch:SETup:ERRor :SERialbus<x>:PSI5:SEARch:SETup:FRAMe Syntax Syntax :PCRC {<Boolean>} inslot:SNUMber {<NRf>} :SERialbus<x>:PSI5:SEARch:SETup:ERRor :SERialbus<x>:PSI5:SEARch:SETup:FRAMe :PCRC? inslot:SNUMber?
Page 226 5.24 SERialbus Group :SERialbus<x>:PSI5:TRENd<y>:CURSor:D :SERialbus<x>:PSI5:TRENd<y>:CURSor:T T:VALue? <z>:VALue? Function Queries the time value between cursors on the Function Queries the time value at the specified cursor on PSI5 signal analysis trend display. the PSI5 signal analysis trend display. :SERialbus<x>:PSI5:TRENd<y>:CURSor:DT :SERialbus<x>:PSI5:TRENd<y>:CURSor:T< Syntax Syntax :VALue? z>:VALue?
Page 227 5.24 SERialbus Group :SERialbus<x>:PSI5:TRENd<y>:VERTical :SERialbus<x>:SENT[:ANALyze]:SETup? Function Sets or queries the vertical range of the PSI5 Function Queries all bus setup settings for SENT signal signal analysis trend display. analysis. :SERialbus<x>:PSI5:TRENd<y>:VERTic :SERialbus<x>:SENT[:ANALyze]:SETup? Syntax Syntax al {<NRf>,<NRf>} <x> = 1 to 4 :SERialbus<x>:PSI5:TRENd<y>:VERTical? :SERialbus<x>:SENT[:ANALyze]:SETup:D <NRf>...
Page 228 5.24 SERialbus Group :SERialbus<x>:SENT[:ANALyze]:SETup:F :SERialbus<x>:SENT[:ANALyze]:SETup:F AST:USETup:DATA<y>? AST:USETup:DATA<y>:SIZE Function Queries all settings related to the specified user- Function Sets or queries the data size of the specified user- defined data of the SENT signal analysis fast defined data of the SENT signal analysis fast channel.
Page 229 5.24 SERialbus Group :SERialbus<x>:SENT[:ANALyze]:SETup:F :SERialbus<x>:SENT[:ANALyze]:SETup:F ORMat:CEFactor:SCPulses ORMat:CTOLerance Function Sets or queries the consecutive calibration pulse Function Sets or queries the SENT signal analysis clock error factor of SENT signal analysis. tolerance. :SERialbus<x>:SENT[:ANALyze]:SETup: :SERialbus<x>:SENT[:ANALyze]:SETup:FO Syntax Syntax FORMat:CEFactor:SCPulses {OFF|OPT2|PO RMat:CTOLerance {<NRf>} PTion} :SERialbus<x>:SENT[:ANALyze]:SETup:FO :SERialbus<x>:SENT[:ANALyze]:SETup: RMat:CTOLerance?
Page 230 5.24 SERialbus Group :SERialbus<x>:SENT[:ANALyze]:SETup:F :SERialbus<x>:SENT:DETail? ORMat:VERSion Function Queries all SENT signal analysis list settings. :SERialbus<x>:SENT:DETail? Function Sets or queries the SENT signal analysis Syntax specification version. <x> = 1 to 4 :SERialbus<x>:SENT[:ANALyze]:SETup:FO Syntax :SERialbus<x>:SENT:DETail:DISPlay RMat:VERSion {FEB2008|JAN2010} :SERialbus<x>:SENT[:ANALyze]:SETup:FO Function Sets or queries the display mode for the SENT RMat:VERESion? signal analysis list.
Page 231 5.24 SERialbus Group :SERialbus<x>:SENT:DETail:LIST:VAL :SERialbus<x>:SENT:SEARch:SELe ct? MAXimum Function Queries all the data for the specified analysis Function Queries the number of detected points in the number in the SENT signal analysis result list. SENT signal search. :SERialbus<x>:SENT:DETail:LIST:VAL :SERialbus<x>:SENT:SEARch:SELe Syntax Syntax ue? {<NRf>|MAXimum|MINimum} ct? {MAXimum} <x>...
Page 232 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch:[SETup]:ER :SERialbus<x>:SENT:SEARch:[SETup]:ER Ror:NDValue Ror:SCRC Function Sets or queries the SENT signal search nibble Function Sets or queries the SENT signal search slow data value error. channel CRC error. :SERialbus<x>:SENT:SEARch:[SETup]:ERR :SERialbus<x>:SENT:SEARch:[SETup]:ERR Syntax Syntax or:NDValue {<Boolean>} or:SCRC {<Boolean>} :SERialbus<x>:SENT:SEARch:[SETup]:ERR :SERialbus<x>:SENT:SEARch:[SETup]:ERR or:NDValue? or:SCRC?
Page 233 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:FD :SERialbus<x>:SENT:SEARch[:SETup]:FD ATa:DATA<y>:CONDition ATa:DNIBbles? Function Sets or queries the comparison condition of the Function Queries all fast channel nibble data settings for specified user data of the SENT signal search fast SENT signal searching. :SERialbus<x>:SENT:SEARch:[SETup]:FDA channel. Syntax :SERialbus<x>:SENT:SEARch[:SETup]:FDA Ta:DNIBbles? Syntax...
Page 234 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch:[SETup]:FD :SERialbus<x>:SENT:SEARch:[SETup]:FS ATa:DNIBbles:PFORmat AComm:PFORmat Function Sets or queries the data input format, which is Function Sets or queries the data input format, which is one of the fast channel nibble data conditions, for one of the fast channel status and communication SENT signal searching.
Page 235 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch:[SETup]:SD :SERialbus<x>:SENT:SEARch[:SETup]:SD ATa:ENHanced:CBIT ATa:ENHanced:D12Bit:DATA:DECimal<y> Function Sets or queries the SENT signal search slow Function Sets or queries the slow channel enhanced type channel enhanced type configuration bit. 12-bit data and 8-bit ID data for SENT signal :SERialbus<x>:SENT:SEARch:[SETup]:SDA Syntax searching in decimal notation.
Page 236 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:SD :SERialbus<x>:SENT:SEARch[:SETup]:SD ATa:ENHanced:D12Bit:DATA:PATTern ATa:ENHanced:D12Bit:ID:CONDition Function Sets the slow channel enhanced type 12-bit data Function Sets or queries the ID comparison condition of and 8-bit ID data for SENT signal searching in slow channel enhanced type 12-bit data and 8-bit binary notation.
Page 237 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:SD :SERialbus<x>:SENT:SEARch[:SETup]:SD ATa:ENHanced:D16Bit? ATa:ENHanced:D16Bit:DATA:HEXa Function Queries all slow channel enhanced type 16- Function Sets the slow channel enhanced type 16-bit data bit data and 4-bit ID settings for SENT signal and 4-bit ID data for SENT signal searching in searching.
Page 238 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:SD :SERialbus<x>:SENT:SEARch[:SETup]:SD ATa:ENHanced:D16Bit:DATA:PFORmat ATa:ENHanced:D16Bit:ID:DECimal<y> Function Sets or queries the data input format, which is Function Sets the ID of the slow channel enhanced type 16- one of the slow channel enhanced type 16-bit bit data and 4-bit ID for SENT signal searching in data and 4-bit ID data conditions, for SENT signal decimal notation.
Page 239 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:SD :SERialbus<x>:SENT:SEARch[:SETup]:SD ATa:SHORt:DATA:CONDition ATa:SHORt:DATA:MODE Function Sets or queries the short type data comparison Function Sets or queries the short type data enable/disable condition of the SENT signal search slow channel. condition of the SENT signal search slow channel. :SERialbus<x>:SENT:SEARch[:SETup]: :SERialbus<x>:SENT:SEARch[:SETup]:SDA Syntax...
Page 240 5.24 SERialbus Group :SERialbus<x>:SENT:SEARch[:SETup]:SD :SERialbus<x>:SENT:TRENd<y>? ATa:SHORt:ID? Function Queries all SENT signal analysis trend display Function Queries all slow channel short type ID settings for settings. :SERialbus<x>:SENT:TRENd<y>? SENT signal searching. Syntax :SERialbus<x>:SENT:SEARch:[SETup]:SDA Syntax <x> = 1 to 4 Ta:SHORt:ID? <y> = 1 to 4 <x>...
Page 241 5.24 SERialbus Group :SERialbus<x>:SENT:TRENd<y>:CURSor:P :SERialbus<x>:SENT:TRENd<y>:HRANge OSition<z> Function Sets or queries the SENT signal analysis trend Function Sets or queries the position of the specified cursor display source window. :SERialbus<x>:SENT:TRENd<y>:HRAN on the SENT signal analysis trend display. Syntax :SERialbus<x>:SENT:TRENd<y>:CURSor:PO ge {MAIN|Z1|Z2} Syntax Sition<y>...
Page 242 5.24 SERialbus Group :SERialbus<x>:SENT:TRENd<y>:VERTical :SERialbus<x>:SOURce:{CHANnel<y>|MAT H<y>}:HYSTeresis Function Sets or queries the vertical range of the SENT signal analysis trend display. Function Sets or queries a source waveform hysteresis. :SERialbus<x>:SENT:TRENd<y>:VERTic :SERialbus<x>:SOURce:{CHANnel<y>|MATH Syntax Syntax al {<NRf>,<NRf>} <y>}:HYSTeresis {<NRf>} :SERialbus<x>:SENT:TRENd<y>:VERTical? :SERialbus<x>:SOURce:{CHANnel<y>|MATH <y>}:HYSTeresis? <x> = 1 to 4 <y>...
Page 243 5.24 SERialbus Group :SERialbus<x>:SPATtern[:ANALyze]:SET :SERialbus<x>:SPATtern[:ANALyze]:SET up:CLOCk:POLarity Function Queries all user-defined bus signal analysis Function Sets or queries the clock signal slope for user- settings. defined bus signal analysis. :SERialbus<x>:SPATtern[:ANALyze]:SET :SERialbus<x>:SPATtern[:ANALyze]:SETu Syntax Syntax p:CLOCk:POLarity {FALL|RISE} :SERialbus<x>:SPATtern[:ANALyze]:SETu <x> = 1 to 4 (1 only for 2-channel models) p:CLOCk:POLarity? :SERialbus<x>:SPATtern[:ANALyze]:SET <x>...
Page 244 5.24 SERialbus Group :SERialbus<x>:SPATtern[:ANALyze]:SET :SERialbus<x>:SPATtern[:ANALyze]:SET up:DATA:SOURce up:CS:SOURce Function Sets or queries the data signal for user-defined Function Sets or queries the chip select signal for user- bus signal analysis. defined bus signal analysis. :SERialbus<x>:SPATtern[:ANALyze]:SETu Syntax :SERialbus<x>:SPATtern[:ANALyze]:SETu Syntax p:DATA:SOURce {<NRf>} p:CS:SOURce {<NRf>|NONE} :SERialbus<x>:SPATtern[:ANALyze]:SETu :SERialbus<x>:SPATtern[:ANALyze]:SETu p:DATA:SOURce?
Page 245 5.24 SERialbus Group :SERialbus<x>:SPATtern[:ANALyze]:SET :SERialbus<x>:SPATtern:SEARch:SELect up:LATCh:SOURce Function Sets which detected point to display in the user- Function Sets or queries the latch signal for user-defined defined bus signal search zoom window and bus signal analysis. queries the zoom position of the detected point. :SERialbus<x>:SPATtern[:ANALyze]:SETu :SERialbus<x>:SPATtern:SEARch:SELe Syntax...
Page 246 5.24 SERialbus Group :SERialbus<x>:SPATtern:SEARch:SETup: :SERialbus<x>:SPI[:ANALyze]:SETup? HEXa Function Queries all SPI bus signal analysis bus settings. :SERialbus<x>:SPI[:ANALyze]:SETup? Function Sets or queries the data condition for user-defined Syntax bus signal searching in hexadecimal notation. <x> = 1 to 4 :SERialbus<x>:SPATtern:SEARch:SETup:H Syntax :SERialbus<x>:SPI[:ANALyze]:SETup:BI EXa {<String>} Torder <x>...
Page 247 5.24 SERialbus Group :SERialbus<x>:SPI[:ANALyze]:SETup:CL :SERialbus<x>:SPI[:ANALyze]:SETup:CS OCk:SOURce :SOURce Function Sets or queries the clock signal for SPI bus signal Function Sets or queries the chip select signal for SPI bus analysis. signal analysis. :SERialbus<x>:SPI[:ANALyze]:SETup:CLO :SERialbus<x>:SPI[:ANALyze]:SETup:CS: Syntax Syntax Ck:SOURce {<NRf>|BIT<x>|MATH<x>} SOURce {<NRf>|BIT<x>|MATH<x>} :SERialbus<x>:SPI[:ANALyze]:SETup:CLO :SERialbus<x>:SPI[:ANALyze]:SETup:CS: Ck:SOURce?
Page 248 5.24 SERialbus Group :SERialbus<x>:SPI[:ANALyze]:SETup:FI :SERialbus<x>:SPI[:ANALyze]:SETup:MO Function Sets or queries the data field size for SPI bus Function Sets or queries the data signal wiring system signal analysis. (three-wire or four-wire) for SPI bus signal :SERialbus<x>:SPI[:ANALyze]:SETup:FIE Syntax analysis. Ld {<NRf>} :SERialbus<x>:SPI[:ANALyze]:SETup:MO Syntax :SERialbus<x>:SPI[:ANALyze]:SETup:FIE DE {WIRE3|WIRE4}...
Page 249 5.24 SERialbus Group :SERialbus<x>:SPI:DETail:LIST:ITEM? :SERialbus<x>:SPI:SEARch:SELect? MAXimum Function Queries all items that will be displayed in the SPI bus signal analysis result list. Function Queries the number of detected points in the SPI :SERialbus<x>:SPI:DETail:LIST:ITEM? Syntax bus signal search. :SERialbus<x>:SPI:SEARch:SELe <x> = 1 to 4 Syntax :SERIALBUS1:SPI:DETAIL:LIST:ITEM? ct? {MAXimum}...
Page 250 5.24 SERialbus Group :SERialbus<x>:SPI:SEARch[:SETup]:DAT :SERialbus<x>:SPI:SEARch[:SETup]:DAT A<y>:CONDition A<y>:MODE Function Sets or queries the data comparison condition (true Function Sets or queries the data enable/disable condition or false) for SPI bus signal searching. for SPI bus signal searching. :SERialbus<x>:SPI:SEARch[:SETup]:DATA :SERialbus<x>:SPI:SEARch[:SETup]:DATA Syntax Syntax <y>:CONDition {FALSe|TRUE} <y>:MODE {<Boolean>} :SERialbus<x>:SPI:SEARch[:SETup]:DATA...
Page 251 5.24 SERialbus Group :SERialbus<x>:TYPE :SERialbus<x>:UART[:ANALyze]:SETup:B RATe Function Sets or queries search type. :SERialbus<x>:TYPE {CANFDbus|CANBus|F Syntax Function Sets or queries the UART signal analysis bit rate LEXray|I2CBus|LINBus|PSI5|SENT|SPATte (data transfer rate). rn|SPIBus|UART} :SERialbus<x>:UART[:ANALyze]:SETup:BR Syntax :SERialbus<x>:TYPE? ATe {<NRf>|USER,<NRf>} :SERialbus<x>:UART[:ANALyze]:SETup:BR <x> = 1 to 4 (1 only for 2-channel models) :SERIALBUS1:TYPE CANBUS ATe? Example...
Page 252 5.24 SERialbus Group :SERialbus<x>:UART[:ANALyze]:SETup:P :SERialbus<x>:UART:DETail:DISPlay OLarity Function Sets or queries the display mode for the UART Function Sets or queries the polarity setting for UART signal signal analysis result list. :SERialbus<x>:UART:DETail:DISPlay {FU analysis. Syntax :SERialbus<x>:UART[:ANALyze]:SETup:PO LL|LOWer|UPPer} Syntax Larity {NEGative|POSitive} :SERialbus<x>:UART:DETail:DISPlay? :SERialbus<x>:UART[:ANALyze]:SETup:PO <x>...
Page 253 5.24 SERialbus Group :SERialbus<x>:UART:SEARch:SELect :SERialbus<x>:UART:SEARch:SETup:DATA :CONDition Function Sets which detected point to display in the UART signal search zoom window and queries the zoom Function Sets or queries the data comparison condition (true position of the detected point. or false) for UART signal searching. :SERialbus<x>:UART:SEARch:SELe :SERialbus<x>:UART:SEARch:SETup:DATA: Syntax...
Page 254 5.24 SERialbus Group :SERialbus<x>:UART:SEARch:SETup:DATA :SERialbus<x>:UART:SEARch:SETup:ERRo :HEXa<y> r:FRAMing Function Sets the data for UART signal searching in Function Sets or queries the UART signal search framing hexadecimal notation. error setting. :SERialbus<x>:UART:SEARch:SETup:DATA: :SERialbus<x>:UART:SEARch:SETup: Syntax Syntax HEXa<y> {<String>} ERRor:FRAMing {<Boolean>} :SERialbus<x>:UART:SEARch:SETup: <x> = 1 to 4 ERRor:FRAMing? <y>...
Page 255 5.24 SERialbus Group :SERialbus<x>:UART:SEARch:SETup:FORM Function Sets or queries the format setting for UART signal analysis. :SERialbus<x>:UART:SEARch:SETup:FORM Syntax at {BIT7Parity|BIT8Parity| BIT8Noparity} :SERialbus<x>:UART:SEARch:SETup:FORM <x> = 1 to 4 :SERIALBUS1:UART:SEARCH:SETUP:FORM Example AT BIT7PARITY :SERIALBUS1:UART:SEARCH:SETUP:FORMAT? -> :SERIALBUS1:UART:SEARCH:SETUP:FORM AT BIT7PARITY :SERialbus<x>:UART:SEARch:SETup:MODE Function Sets or queries the UART signal search mode. :SERialbus<x>:UART:SEARch:SETup:MO Syntax DE {DATA|EDATA|ERRor}...
Page 256: Snap Group
5.25 SNAP Group :SNAP Function Takes a snapshot. :SNAP Syntax :SNAP Example Index 5-223 IM 710105-17E...
Page 257: Sstart Group
5.26 SSTart Group :SSTart? Function Sets the trigger mode to SINGLE, and starts waveform acquisition. Returns zero if data acquisition is stopped before the specified time period. Returns 1 if waveform acquisition is not stopped within the specified time period. :SSTart? {<NRf>} Syntax <NRf>...
Page 258: Start Group
5.27 STARt Group :STARt Function Starts waveform acquisition. :STARt Syntax :START Example Description Stop waveform acquisition by using the STOP command. Index 5-225 IM 710105-17E...
Page 259: Status Group
5.28 STATus Group The commands in the STATus group are used to make settings and inquiries related to the communication status feature. There are no front panel keys that correspond to the commands in this group. For information about status reports, see chapter 6.
Page 260: Stop Group
5.29 STOP Group :STOP Function Stops waveform acquisition. :STOP Syntax :STOP Example Description Start waveform acquisition by using the STARt command. Index 5-227 IM 710105-17E...
Page 261: Store Group
5.30 STORe Group :STORe? Function Queries all of the information related to setup data in the internal memory. :STORe? Syntax :STORe:SETup<x>? Function Queries information about the setup data in the specified location of the internal memory. :STORe:SETup<x>? Syntax <x> = 1 to 3 :STORe:SETup<x>:COMMent Function Sets or queries the comment for the setup data...
Page 262: System Group
5.31 SYSTem Group :SYSTem? :SYSTem:CLOCk:SNTP:EXECute Function Queries all system settings. Function Sets the date and time using SNTP. :SYSTem? :SYSTem:CLOCk:SNTP:EXECute Syntax Syntax :SYSTEM:CLOCK:SNTP:EXECUTE Example :SYSTem:BEEP :SYSTem:CLOCk:SNTP:GMTTime Function Generates a beep sound. :SYSTem:BEEP Syntax Function Sets or queries the time difference from Greenwich :SYSTEM:BEEP Example Mean Time.
Page 263 5.31 SYSTem Group :SYSTem:LANGuage :SYSTem:LMODe (Legacy Mode) Function Sets or queries the message language. Function Sets or queries whether to initialize the settings to :SYSTem:LANGuage {CHINese|ENGLish|FRE Syntax the default values of legacy models when Default Nch|GERMan|ITALian|JAPANese|KORean|RU Setup is executed. SSian|SPANish} :SYSTem:LMODe {<Boolean>} Syntax :SYSTem:LANGuage?
Page 264: Timebase Group
5.32 TIMebase Group :TIMebase? Function Queries all time base settings. :TIMebase? Syntax :TIMebase:SRATe? (Sample RATE) Function Queries the sample rate. :TIMebase:SRATe? Syntax :TIMEBASE:SRATE? Example -> :TIMEBASE:SRATE 12.50E+06 :TIMebase:TDIV Function Sets or queries the Time/div value. :TIMebase:TDIV {<Time>} Syntax :TIMebase:TDIV? <Time> = 500 ps to 500 s :TIMEBASE:TDIV 2NS Example :TIMEBASE:TDIV?
Page 265: Trigger Group
5.33 TRIGger Group The following table indicates how the communication commands for trigger types correspond to the menu items that appear on the screen. Trigger Type Communication Setup Menu Command Trigger Menu Trigger Type Edge trigger SIMPle EDGE — Trigger on the OR of multiple edge triggers ENHANCED Edge OR Edge qualified trigger...
Page 266 5.33 TRIGger Group :TRIGger:ACTion:HCOPy :TRIGger:ACTion:STOP Function Sets or queries whether or not the DLM2000 will Function Stops the action-on-trigger operation. :TRIGger:ACTion:STOP print a screen capture as an action when trigger Syntax :TRIGGER:ACTION:STOP conditions are met (on/off). Example :TRIGger:ACTion:HCOPy {<Boolean>} Syntax Description This command only stops trigger actions :TRIGger:ACTion:HCOPy? and does not cancel the setting.
Page 267 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN: :TRIGger{[:ATRigger]|:BTRigger}:CAN[ EFRame:CRC :IDData]:ACK:MODE Function Sets or queries the CAN bus signal trigger CRC Function Sets or queries the ACK mode, which is one of error setting. the ID and data conditions, for CAN bus signal :TRIGger{[:ATRigger]|:BTRigger}:CAN:E Syntax triggering.
Page 268 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :IDData]:DATA:DECimal<x> :IDData]:DATA:HEXa<x> Function Sets a reference value, which is one of the ID and Function Sets a reference value, which is one of the ID and data conditions, for CAN bus signal triggering in data conditions, for CAN bus signal triggering in decimal notation.
Page 269 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :IDData]:DATA:PATTern<x> :IDData]:IDENtifier:ID? Function Sets or queries the data value, which is one of Function Queries all ID settings for the ID and data the ID and data conditions, for CAN bus signal conditions for CAN bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:CAN[: triggering in binary notation.
Page 270 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :IDData]:IDENtifier:MFORmat :IDData]:MSIGnal:SELect Function Sets or queries the ID frame format (standard Function Sets or queries the message and signal conditions or extended), which is one of the ID and data for CAN bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:CAN[: conditions, for CAN bus signal triggering.
Page 271 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN[ :TRIGger{[:ATRigger]|:BTRigger}:CAN: :IDData]:MSIGnal:SIGNal:DECimal<x> IDOR:ACK? Function Sets a signal reference value, which is one of Function Queries all IDOR condition ACK settings for CAN the ID and data conditions, for CAN bus signal bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:CAN:I triggering in decimal notation. Syntax :TRIGger{[:ATRigger]|:BTRigger}:CA DOR:ACK?
Page 272 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN: :TRIGger{[:ATRigger]|:BTRigger}:CAN: IDOR:IDENtifier? IDOR:IDENtifier:ID<x>:PATTern Function Queries all identifier settings for the IDOR Function Sets or queries the ID pattern, which is one of the condition for CAN bus signal triggering. IDOR conditions, for CAN bus signal triggering in :TRIGger{[:ATRigger]|:BTRigger}:CAN:I Syntax binary notation.
Page 273 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:CAN: :TRIGger{[:ATRigger]|:BTRigger}:CAN: IDOR:IDENtifier:PFORmat RECessive Function Sets or queries the ID input format, which is Function Sets or queries the CAN bus signal trigger one of the IDOR conditions, for CAN bus signal recessive level. :TRIGger{[:ATRigger]|:BTRigger}:CAN:R triggering. Syntax :TRIGger{[:ATRigger]|:BTRigger}:CAN:I ECessive {HIGH|LOW} Syntax...
Page 274 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray:BRATe ray:ERRor:FES Function Sets or queries the FLEXRAY bus signal trigger bit Function Sets or queries the FLEXRAY bus signal trigger rate (data transfer rate). FES error setting. :TRIGger{[:ATRigger]|:BTRigger}:FLEXr :TRIGger{[:ATRigger]|:BTRigger}:FLEXr Syntax Syntax ay:BRATe {<NRf>} ay:ERRor:FES {<Boolean>} :TRIGger{[:ATRigger]|:BTRigger}:FLEXr :TRIGger{[:ATRigger]|:BTRigger}:FLEXr ay:BRATe?
Page 275 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray[:IDData]:CCOunt:COUNt<x> ray[:IDData]:DATA<x>:BCOunt Function Sets or queries the cycle count, which is one of Function Sets or queries the position for comparing data the ID and data conditions, for FLEXRAY bus field data patterns, which is one of the ID and data signal triggering.
Page 276 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray[:IDData]:DATA<x>:DECimal<y> ray[:IDData]:DATA<x>:MODE Function Sets a reference value, which is one of the ID and Function Sets or queries the data field enable/disable data conditions, for FLEXRAY bus signal triggering condition, which is one of the ID and data in hexadecimal notation.
Page 277 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray[:IDData]:DATA<x>:PFORmat ray[:IDData]:FID:CONDition Function Sets or queries the data field data input format, Function Sets or queries the frame ID data condition, which which is one of the ID and data conditions, for is one of the ID and data conditions, for FLEXRAY FLEXRAY bus signal triggering.
Page 278 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray[:IDData]:INDIcator:MODE ray[:IDData]:INDIcator:STFRame Function Sets or queries the indicator enable/disable Function Sets or queries the indicator start frame, which is condition, which is one of the ID and data one of the ID and data conditions, for FLEXRAY conditions, for FLEXRAY bus signal triggering.
Page 279 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:FLEX ray:IDOR:ID<x>:CCOunt:CONDition ray:IDOR:ID<x>:FID:CONDition Function Sets or queries the comparison condition for the Function Sets or queries the ID comparison condition of the cycle counts of the frame IDs for FLEXRAY bus frame IDs for FLEXRAY bus signal triggering (this signal triggering (this is one of the OR conditions).
Page 280 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:FLEX :TRIGger{[:ATRigger]|:BTRigger}:I2C: ray:MODE ADDRess:ADDRess:BIT10ADdress:HEXa Function Sets or queries the FLEXRAY bus signal trigger Function Sets the 10-bit address for I C bus signal mode. triggering in hexadecimal notation. :TRIGger{[:ATRigger]|:BTRigger}:FLEXr :TRIGger{[:ATRigger]|:BTRigger}:I2C:A Syntax Syntax ay:MODE {ERRor|FSTart|IDData|IDOR} DDRess:ADDRess:BIT10ADdress: :TRIGger{[:ATRigger]|:BTRigger}:FLEXr HEXa {<String>} ay:MODE? :TRIGGER:ATRIGGER:I2C:ADDRESS:ADDRESS Example...
Page 281 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:I2C: :TRIGger{[:ATRigger]|:BTRigger}:I2C: ADDRess:ADDRess[:BIT7ADdress]:PATTe ADDRess:ADDRess:BIT7APsub:ADDRess:PA TTern Function Sets or queries the 7-bit address for I C bus signal Function Sets or queries the 7-bit address for the 7-bit + triggering in binary notation. sub address for I C bus signal triggering in binary :TRIGger{[:ATRigger]|:BTRigger}:I2C: Syntax notation.
Page 282 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:I2C: :TRIGger{[:ATRigger]|:BTRigger}:I2C: ADDRess:ADDRess:MODE ADDRess:DATA:BCOunt Function Sets or queries the address condition enable/ Function Sets or queries the position for comparing data disable mode for I C bus signal triggering. patterns for I C bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:I2C:A :TRIGger{[:ATRigger]|:BTRigger}:I2C:A Syntax Syntax...
Page 283 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:I2C: :TRIGger{[:ATRigger]|:BTRigger}:I2C: ADDRess:DATA:DBYTe ADDRess:DATA:PFORmat Function Sets or queries the specified number of data bytes Function Sets or queries the data input format, which is one for I C bus signal triggering. of the data conditions, for I C bus signal triggering.
Page 284 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:I2C: :TRIGger{[:ATRigger]|:BTRigger}:I2C: GENeralcall:SBYTe NONack:HSMode Function Sets or queries the general call’s second byte type Function Sets or queries whether or not NON ACK will be for I C bus signal triggering. ignored in high-speed mode for I C bus signal :TRIGger{[:ATRigger]|:BTRigger}:I2C:G Syntax...
Page 285 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:I2C: :TRIGger{[:ATRigger]|:BTRigger}:LIN: BRATe Function Sets or queries the clock signal for I C bus signal Function Sets or queries the LIN bus signal trigger bit rate triggering. (data transfer rate). :TRIGger{[:ATRigger]|:BTRigger}:I2C:S :TRIGger{[:ATRigger]|:BTRigger}:LIN:B Syntax Syntax CL {<NRf>|BIT<x>} RATe {<NRf>|USER,<NRf>} :TRIGger{[:ATRigger]|:BTRigger}:I2C:S :TRIGger{[:ATRigger]|:BTRigger}:LIN:B RATe?
Page 286 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:LIN: :TRIGger{[:ATRigger]|:BTRigger}:LIN: IDData? IDData:DATA:DECimal<x> Function Queries all ID and data settings for LIN bus signal Function Sets the data for LIN bus signal triggering in triggering. decimal notation. :TRIGger{[:ATRigger]|:BTRigger}:LIN:I :TRIGger{[:ATRigger]|:BTRigger}:LIN:I Syntax Syntax DData? DData:DATA:DECimal<x> {<NRf>} :TRIGger{[:ATRigger]|:BTRigger}:LIN:I :TRIGger{[:ATRigger]|:BTRigger}:LIN: DData:DATA:DECimal<x>? IDData:DATA? <x>...
Page 287 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:LIN: :TRIGger{[:ATRigger]|:BTRigger}:LIN: IDData:DATA:MSBLsb IDData:DATA:SIGN Function Sets or queries the data MSB and LSB bits for LIN Function Sets or queries whether signed or unsigned data bus signal triggering. format will be used, which is one of the data :TRIGger{[:ATRigger]|:BTRigger}:LIN:I Syntax conditions, for LIN bus signal triggering.
Page 288 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:LIN: :TRIGger{[:ATRigger]|:BTRigger}:LIN: IDData:IDENtifier:ID:PATTern IDOR:IDENtifier:ID<x>:HEXa Function Sets or queries the ID value for LIN bus signal Function Sets the ID value, which is one of the IDOR triggering in binary notation. conditions, for LIN bus signal triggering in :TRIGger{[:ATRigger]|:BTRigger}:LIN: Syntax hexadecimal notation.
Page 289 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:PATT :TRIGger{[:ATRigger]|:BTRigger}:LIN: ern? IDOR:IDENtifier:PFORmat Function Queries all state trigger settings. Function Sets or queries the ID input format, which is one of :TRIGger{[:ATRigger]|:BTRigger}:PATTe Syntax the IDOR conditions, for LIN bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:LIN:I Syntax DOR:IDENtifier:PFORmat {BINary|HEXa} :TRIGger{[:ATRigger]|:BTRigger}:PATT :TRIGger{[:ATRigger]|:BTRigger}:LIN:I ern:BITS? DOR:IDENtifier:PFORmat?
Page 290 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:PATT :TRIGger{[:ATRigger]|:BTRigger}:PATT ern:CLOCk? ern:LOGic Function Queries all clock signal settings for state Function Sets or queries the combination condition for state triggering. triggering. :TRIGger{[:ATRigger]|:BTRigger}:PATTe :TRIGger{[:ATRigger]|:BTRigger}:PATTe Syntax Syntax rn:CLOCk? rn:LOGic {AND|OR} :TRIGger{[:ATRigger]|:BTRigger}:PATTe :TRIGger{[:ATRigger]|:BTRigger}:PATT rn:LOGic? ern:CLOCk:SLOPe :TRIGGER:ATRIGGER:PATTERN:LOGIC AND Example :TRIGGER:ATRIGGER:PATTERN:LOGIC? Function Sets or queries the clock signal slope for state...
Page 291 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SIMP :TRIGger{[:ATRigger]|:BTRigger}:SIMP le:COUPling le:LEVel Function Sets or queries the edge trigger source trigger Function Sets or queries the edge trigger source trigger coupling. level. :TRIGger{[:ATRigger]|:BTRigger}:SIMPl :TRIGger{[:ATRigger]|:BTRigger}:SIMPl Syntax Syntax e:COUPling {AC|DC} e:LEVel {<Voltage>} :TRIGger{[:ATRigger]|:BTRigger}:SIMPl :TRIGger{[:ATRigger]|:BTRigger}:SIMPl e:COUPling? e:LEVel? :TRIGGER:ATRIGGER:SIMPLE:COUPLING AC Example <Voltage>...
Page 292 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SIMP :TRIGger{[:ATRigger]|:BTRigger}:SIMP le:SLOPe le:WINDow Function Sets or queries trigger source trigger slope (the Function Sets or queries the edge trigger source window. :TRIGger{[:ATRigger]|:BTRigger}:SIMPl polarity when window is set to ON) for edge Syntax e:WINDow {<Boolean>} triggering. :TRIGger{[:ATRigger]|:BTRigger}:SIMPl :TRIGger{[:ATRigger]|:BTRigger}:SIMPl Syntax e:SLOPe {ENTer|EXIT|FALL|RISE}...
Page 293 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SPAT :TRIGger{[:ATRigger]|:BTRigger}:SPAT tern:CLOCk:MODE tern:CS:ACTive Function Sets or queries the clock signal enable or disable Function Sets or queries the chip select signal active state status for user-defined bus signal triggering. for user-defined bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:SPATt :TRIGger{[:ATRigger]|:BTRigger}:SPATt Syntax Syntax ern:CLOCk:MODE {<Boolean>}...
Page 294 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SPAT :TRIGger{[:ATRigger]|:BTRigger}:SPAT tern:DATA:SOURce tern:LATCh:SOURce Function Sets or queries the data signal for user-defined Function Sets or queries the latch signal for user-defined bus signal triggering. bus signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:SPATt :TRIGger{[:ATRigger]|:BTRigger}:SPATt Syntax Syntax ern:DATA:SOURce {<NRf>} ern:LATCh:SOURce {<NRf>|NONE} :TRIGger{[:ATRigger]|:BTRigger}:SPATt :TRIGger{[:ATRigger]|:BTRigger}:SPATt ern:DATA:SOURce? ern:LATCh:SOURce?
Page 295 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SPI: :TRIGger{[:ATRigger]|:BTRigger}:SPI: BITorder Function Sets or queries the bit order of the SPI bus signal Function Queries all chip select signal settings for SPI bus trigger data. signal triggering. :TRIGger{[:ATRigger]|:BTRigger}:SPI:B :TRIGger{[:ATRigger]|:BTRigger}:SPI: Syntax Syntax ITorder {LSBFirst|MSBFirst} :TRIGger{[:ATRigger]|:BTRigger}:SPI:B :TRIGGER:ATRIGGER:SPI:CS? Example ITorder? ->...
Page 296 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SPI: :TRIGger{[:ATRigger]|:BTRigger}:SPI: DATA<x>:BCOunt DATA<x>:MODE Function Sets or queries the starting position of data Function Sets or queries the data enable/disable condition comparison for SPI bus signal triggering. for SPI bus signal triggering (on/off). :TRIGger{[:ATRigger]|:BTRigger}:SPI:D :TRIGger{[:ATRigger]|:BTRigger}:SPI:D Syntax Syntax ATA<x>:BCOunt {<NRf>} ATA<x>:MODE {<Boolean>} :TRIGger{[:ATRigger]|:BTRigger}:SPI:D...
Page 297 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:SPI: :TRIGger{[:ATRigger]|:BTRigger}:UART DATA<x>:SOURce :BITorder Function Sets or queries the data signal for SPI bus signal Function Sets or queries the UART signal trigger bit order. :TRIGger{[:ATRigger]|:BTRigger}:UART: triggering. Syntax :TRIGger{[:ATRigger]|:BTRigger}:SPI:D BITorder {LSBFirst|MSBFirst} Syntax ATA<x>:SOURce {<NRf>|BIT<x>} :TRIGger{[:ATRigger]|:BTRigger}:UART: :TRIGger{[:ATRigger]|:BTRigger}:SPI:D BITorder? ATA<x>:SOURce? :TRIGGER:ATRIGGER:UART:BITORDER LSBFI Example...
Page 298 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:UART :TRIGger{[:ATRigger]|:BTRigger}:UART :DATA:CSENsitive :DATA:PATTern<x> Function Sets or queries whether to distinguish uppercase Function Sets or queries the data value for UART signal and lowercase letters in ASCII data for the UART triggering in binary notation. :TRIGger{[:ATRigger]|:BTRigger}:UART: bus signal trigger. Syntax :TRIGger{[:ATRigger]|:BTRigger}:UART: DATA:PATTern<x>...
Page 299 5.33 TRIGger Group :TRIGger{[:ATRigger]|:BTRigger}:UART :TRIGger{[:ATRigger]|:BTRigger}:UART :ERRor:PARity :POLarity Function Sets or queries the UART signal trigger parity Function Sets or queries the UART signal trigger polarity. :TRIGger{[:ATRigger]|:BTRigger}:UART: error setting. Syntax :TRIGger{[:ATRigger]|:BTRigger}:UART: POLarity {NEGative|POSitive} Syntax ERRor:PARity {<Boolean>} :TRIGger{[:ATRigger]|:BTRigger}:UART: :TRIGger{[:ATRigger]|:BTRigger}:UART: POLarity? ERRor:PARity? :TRIGGER:ATRIGGER:UART:POLARITY NEGAT Example :TRIGGER:ATRIGGER:UART:ERROR:PARI Example...
Page 300 5.33 TRIGger Group :TRIGger[:ATRigger]:CANFD:DBRate :TRIGger[:ATRigger]:CANFD[:ID]:IDENt ifier:ID? Function Sets or queries the CAN FD bus signal trigger data phase bit rate (data transfer rate). Function Queries all ID settings for the ID conditions for :TRIGger[:ATRigger]:CANFD:DBRa Syntax CAN FD bus signal triggering. te {<NRf>|USER,<NRf>} :TRIGger[:ATRigger]:CANFD[:ID]:IDENti Syntax...
Page 301 5.33 TRIGger Group :TRIGger[:ATRigger]:CANFD[:ID]:IDENt :TRIGger[:ATRigger]:CANFD:IDOR:DATA[ ifier:MFORmat :MODE] Function Sets or queries the ID frame format (standard or Function Sets or queries the data enable/disable condition, extended), which is one of the ID conditions, for which is one of the IDOR conditions, for CAN FD CAN FD bus signal triggering.
Page 302 5.33 TRIGger Group :TRIGger[:ATRigger]:CANFD:IDOR:IDENt :TRIGger[:ATRigger]:CANFD:IDOR:IDENt ifier:ID<x>:MODE ifier:MFORmat Function Sets or queries the ID enable/disable condition, Function Sets or queries the ID frame format (standard or which is one of the IDOR conditions, for CAN FD extended), which is one of the IDOR conditions, bus signal triggering.
Page 303 5.33 TRIGger Group :TRIGger[:ATRigger]:CANFD:MODE :TRIGger[:ATRigger]:OR:CHANnel<x> Function Sets or queries the CAN FD bus signal trigger Function Sets or queries the edge of a channel for edge OR mode. triggering. :TRIGger[:ATRigger]:CANFD:MODE {EFRam :TRIGger[:ATRigger]:OR: Syntax Syntax e|ID|IDOR|SOF} CHANnel<x> {OFF|RISE|FALL|IN|OUT} :TRIGger[:ATRigger]:CANFD:MODE? :TRIGger[:ATRigger]:OR:CHANnel<x>? :TRIGGER:ATRIGGER:CANFD:MODE EFRAME Example <x>...
Page 304 5.33 TRIGger Group :TRIGger[:ATRigger]:PSI5:DATA:HEXa :TRIGger[:ATRigger]:PSI5:SETup:DATA? Function Sets the data for PSI5 signal triggering in Function Queries all PSI5 signal trigger data signal settings. :TRIGger:ATRigger:PSI5:SETup:DATA? hexadecimal notation. Syntax :TRIGger[:ATRigger]:PSI5:DATA:HE Syntax :TRIGger[:ATRigger]:PSI5:SETup:DATA: Xa {<String>} BRATe :TRIGGER:ATRIGGER:PSI5:DATA:HE Example XA "3A0F" Function Sets or queries the PSI5 signal trigger bit rate (data Description This command is valid when :TRIGger[:ATRig transfer rate).
Page 305 5.33 TRIGger Group :TRIGger[:ATRigger]:PSI5:SETup:DATA: :TRIGger[:ATRigger]:PULSe? DBITs Function Queries all pulse width trigger settings. :TRIGger[:ATRigger]:PULSe? Function Sets or queries the data length for PSI5 signal Syntax triggering. :TRIGger[:ATRigger]:PULSe:POLarity :TRIGger[:ATRigger]:PSI5:SETup:DATA:D Syntax BITs {<NRf>} Function Sets or queries the pulse width trigger source :TRIGger[:ATRigger]:PSI5:SETup:DATA:D polarity.
Page 306 5.33 TRIGger Group :TRIGger[:ATRigger]:SENT:PPULse :TRIGger[:ATRigger]:TV:FRAMe Function Sets or queries the presence or absence of pause Function Sets or queries the frame skip feature for TV pulses for SENT signal triggering. triggering. :TRIGger[:ATRigger]:SENT:PPULse {NPP| :TRIGger[:ATRigger]:TV:FRAMe {<NRf>} Syntax Syntax PP|PPC} :TRIGger[:ATRigger]:TV:FRAMe? :TRIGger[:ATRigger]:SENT:PPULse? <NRf>...
Page 307 5.33 TRIGger Group :TRIGger[:ATRigger]:TV:LFORmat :TRIGger[:ATRigger]:TV:USERdefine:HF Rejection (HighFrequencyREJECTION) Function Sets or queries the format for specifying the line where TV triggering will be used. Function Sets or queries the low-pass filter (HF rejection) :TRIGger[:ATRigger]:TV:LFORmat {ALL|O Syntax setting for user-defined TV triggering. :TRIGger[:ATRigger]:TV:USERdefine:HFR Syntax :TRIGger[:ATRigger]:TV:LFORmat?
Page 308 5.33 TRIGger Group :TRIGger[:ATRigger]:TV:USERdefine:PO :TRIGger[:ATRigger]:WIDTh:BITS:PATTe Larity Function Sets or queries the user-defined TV trigger input Function Sets or queries the logic input state pattern for polarity. state width triggering. :TRIGger[:ATRigger]:TV:USERdefine:POL :TRIGger[:ATRigger]:WIDTh:BITS:PATTe Syntax Syntax arity {POSitive|NEGative} rn {<String>} :TRIGger[:ATRigger]:TV:USERdefine:POL :TRIGger[:ATRigger]:WIDTh:BITS:PATTe arity? :TRIGGER:ATRIGGER:TV:USERDEFINE:POLAR :TRIGGER:ATRIGGER:WIDTH:BITS:PATTE Example...
Page 309 5.33 TRIGger Group :TRIGger[:ATRigger]:WIDTh:CLOCk:SOUR :TRIGger[:ATRigger]:WIDTh:TYPE Function Sets or queries the time width mode for state Function Sets or queries the clock signal for state width width triggering. :TRIGger[:ATRigger]:WIDTh:TYPE {IN|OU triggering. Syntax :TRIGger[:ATRigger]:WIDTh:CLOCk:SOUR T|BETWeen|NOTBetween|TIMeout} Syntax ce {<NRf>|DONTcare|BIT<x>} :TRIGger[:ATRigger]:WIDTh:TYPE? :TRIGger[:ATRigger]:WIDTh:CLOCk:SOUR :TRIGGER:ATRIGGER:WIDTH:TYPE IN Example :TRIGGER:ATRIGGER:WIDTH:TYPE? ->...
Page 310 5.33 TRIGger Group :TRIGger:MODE :TRIGger:SOURce:CHANnel<x>:HFRejecti on (HighFrequencyREJECTION) Function Sets or queries the trigger mode. :TRIGger:MODE {AUTO|ALEVel|NORMal|NSI Syntax Function Sets or queries the low-pass filter setting of the Ngle} specified trigger source for enhanced triggering. :TRIGger:MODE? :TRIGger:SOURce:CHANnel<x>:HFRejecti Syntax :TRIGGER:MODE AUTO on {<Frequency>|OFF} Example :TRIGGER:MODE? :TRIGger:SOURce:CHANnel<x>:HFRejecti...
Page 311 5.33 TRIGger Group :TRIGger:SOURce:CHANnel<x>:WIDTh Function Sets or queries the window width of the specified trigger source for enhanced triggering. :TRIGger:SOURce:CHANnel<x>:WID Syntax Th {<Voltage>} :TRIGger:SOURce:CHANnel<x>:WIDTh? <x> = 1 to 4 (1 or 2 for 2-channel models) <Voltage> = See the DLM2000 Features Guide for this information.
Page 312: Waveform Group
5.34 WAVeform Group The commands in this group deal with the retrieved waveform data. There are no front panel keys that correspond to the commands in this group. :WAVeform? :WAVeform:ALL:SEND? Function Queries all information about waveform data. Function Queries the waveform data specified by the :WAVeform? Syntax :WAVeform:ALL:TRACe command.
Page 313 5.34 WAVeform Group :WAVeform:ALL:TRACe :WAVeform:LENGth? Function Sets or queries the waveform that is the target of Function Queries the total number of data points the :WAVeform:ALL:SEND? query. of the waveform data specified by the :WAVeform:ALL:TRACe {<NRf>|ALL|LOGic| :WAVeform:TRACe command. Syntax MATH<x>} :WAVeform:LENGth? Syntax :WAVeform:ALL:TRACe?
Page 314 5.34 WAVeform Group :WAVeform:RECord? MINimum :WAVeform:SRATe? (Sample RATE) Function Queries the minimum record number of the source Function Queries the sample rate of the record specified by the :WAVeform:RECord command. channel. :WAVeform:RECord? MINimum :WAVeform:SRATe? Syntax Syntax :WAVEFORM:RECORD? MINIMUM :WAVEFORM:SRATE? Example Example -> :WAVEFORM:RECORD −49999 ->...
Page 315: Wparameter Group
5.35 WPARameter Group :WPARameter<x>? :WPARameter<x>:HISTogram:MEASure:PAR ameter? Function Queries all of the settings for the waveform parameter measurement feature. Function Queries all automatic measurement settings of :WPARameter<x>? Syntax the histogram parameter for waveform parameter <x> = 1 or 2 (1 only for 2-channel models) measurement.
Page 316 5.35 WPARameter Group :WPARameter<x>:HISTogram:MEASure:PAR :WPARameter<x>:ITEM ameter:<Parameter>:STATe Function Sets or queries a waveform parameter for Function Sets or queries the on/off status of a histogram waveform parameter measurement. :WPARameter<x>:ITEM {<NRf>|BIT<x>| parameter for waveform parameter measurement. Syntax :WPARameter<x>:HISTogram:MEASure:PARa MATH<x>,<Parameter>,{2}} Syntax meter:<Parameter>:STATe {<Boolean>} :WPARameter<x>:ITEM? :WPARameter<x>:HISTogram:MEASure:PARa <x>...
Page 317 5.35 WPARameter Group :WPARameter<x>:TRENd:CURSor? :WPARameter<x>:TRENd:CURSor:POSition <y> Function Queries all cursor measurement settings of the trend display for waveform parameter Function Sets or queries the position of a cursor in the trend measurement. display for waveform parameter measurement. :WPARameter<x>:TRENd:CURSor? :WPARameter<x>:TRENd:CURSor:POSition Syntax Syntax <y>...
Page 318 5.35 WPARameter Group :WPARameter<x>:VTDisplay Function Sets or queries the on/off status of VT waveform display. :WPARameter<x>:VTDisplay {<Boolean>} Syntax :WPARameter<x>:VTDisplay? <x> = 1 or 2 (1 only for 2-channel models) :WPARAMETER1:VTDISPLAY ON Example :WPARAMETER1:VTDISPLAY? -> :WPARAMETER1:VTDISPLAY 1 :WPARameter<x>:WAIT? Function Waits for the completion of automated measurement with a set timeout.
Page 319: Xy Group
5.36 XY Group :XY<x>? :XY<x>:MEASure:CURSor:DX:VALue? Function Queries all XY display settings. Function Queries the voltage difference between the X-Y :XY<x>? Syntax display's horizontal cursors. :XY<x>:MEASure:CURSor:DX:VALue? <x> = 1 or 2 (1 only for 2-channel models) Syntax <x> = 1 or 2 (1 only for the DLM2022, DLM2032, :XY<x>:DISPlay DLM2052) :XY1:MEASURE:CURSOR:DX:VALUE?
Page 320 5.36 XY Group :XY<x>:MEASure:CURSor:X<y>:POSition :XY<x>:MEASure:CURSor:Y<y>:POSition Function Sets or queries a horizontal cursor position in the Function Sets or queries a vertical cursor position in the XY XY display. display. :XY<x>:MEASure:CURSor:X<y>:POSiti :XY<x>:MEASure:CURSor:Y<y>:POSiti Syntax Syntax on {<NRf>} on {<NRf>} :XY<x>:MEASure:CURSor:X<y>:POSition? :XY<x>:MEASure:CURSor:Y<y>:POSition? <x> = 1 or 2 (1 only for 2-channel models) <x>...
Page 321 5.36 XY Group :XY<x>:MEASure:INTeg:POLarity :XY<x>:VTDisplay Function Sets or queries the integration polarity for the XY Function Sets or queries the on/off status of the VT display. waveform display for the XY display. :XY<x>:MEASure:INTeg:POLarity {CCW|CW :XY<x>:VTDisplay {<Boolean>} Syntax Syntax :XY<x>:VTDisplay? :XY<x>:MEASure:INTeg:POLarity? <x>...
Page 322: Zoom Group
5.37 ZOOM Group :ZOOM<x>? :ZOOM<x>:MAG Function Queries all waveform zoom settings. Function Sets or queries the magnification of a zoom :ZOOM<x>? Syntax waveform display. :ZOOM<x>:MAG {<NRf>} <x> = 1 or 2 Syntax :ZOOM<x>:MAG? :ZOOM<x>:ALLocation? <x> = 1 or 2 Function Queries all zoom source waveform settings.
Page 323 5.37 ZOOM Group :ZOOM<x>:VERTical:{CHANnel<y>|MATH :ZOOM<x>:VERTical:TRACe <y>}? Function Sets or queries the trace that is displayed in the Function Queries all of the settings of a trace for vertical vertical zoom window. :ZOOM<x>:VERTical:TRACe {<NRf>|MATH<x zooming. Syntax :ZOOM<x>:VERTical:{CHANnel<y>| >} Syntax MATH<y>}? :ZOOM<x>:VERTical:TRACe? <x>...
Page 324: Common Command Group
Sets or queries the standard event enable register. Syntax *ESE {<NRf>} *IDN? Index Syntax Example *ESE? -> YOKOGAWA,710120,08ELP1024,F1.01 <NRf> = 0 to 255 Description The information is returned in this *ESE 251 Example form:<Manufacturer>, <Model>, <Serial no.>, *ESE? <Firmware version>.
Page 325 5.38 Common Command Group *OPC? (OPeration Complete) *SRE (Service Request Enable register) Function If you send *OPC?, the DLM2000 returns ASCII code 1 when the specified overlap command is Function Sets or queries the service request enable register completed. value. *OPC? *SRE <NRf>...
Page 326 5.38 Common Command Group *WAI (WAIt) Function Holds the subsequent command until the completion of the specified overlap operation. *WAI Syntax *WAI Example Description • For information about how to synchronize a program using *WAI , see page 5-7. • The :COMMunicate:OPSE command is used to specify the overlap command.
Page 327: Chapter 6 Status Reports
Chapter 6 Status Reports About Status Reports Status Reports The figure below shows the format of status reports that are read by serial polling. This status report format is an extended version of the status report format defined in IEEE 488.2-1992. Service request enable register &...
Page 328 6.1 About Status Reports Overview of Registers and Queues Name Function Write Read − Serial polling (RQS) , Status byte − *STB? (MSS) *SRE *SRE? Service request enable Status byte mask register − *ESR? Standard event register Indicates device status changes *ESE *ESE?
Page 329: Status Byte
Status Byte Status byte Status Byte Operation A service request is issued when bit 6 in the status 6 ESB MAV EES EAV 1 byte becomes 1. Bit 6 is set to 1 when any other bit is 1 (when the corresponding bit of the service request enable register is also set to 1).
Page 330: Standard Event Register
Standard Event Register Standard Event Register Standard Event Register Operation The standard event register indicates eight types of CME EXE DDE QYE RQC OPC events that occur inside the DLM2000. When one of the bits in this register is 1 (and the corresponding bit •...
Page 331: Extended Event Register
Extended Event Register The extended event register receives information about changes in the condition register, which indicates the DLM2000’s internal condition. The information is the result of edge detection performed by the transition filter. FILTer<x>→ Condition register :STATus:CONDition? Transition filter :STATus:FILTer<x>...
Page 332: Output And Error Queues
Output and Error Queues Output Queue The output queue stores query response messages. For example, if you send a :WAVeform: SEND? command, which requests for the transmission of acquired data, the data is stored in the output queue until it is read. As shown below, data is stored in order and read from the oldest message first.
Page 333: Ascii Character Codes
Appendix Appendix 1 ASCII Character Codes The following table contains ASCII character codes. ‘ ” & ’ Index < > (RUBOUT) Address Universal Listener Talker Secondary command command address address command Example Octal GP-IB code ASCII character code Hexadecimal Decimal App-1 IM 710105-17E...
Page 334 PC or other similar device, messages are displayed in English. • If servicing is necessary to solve the problem indicated by a message, contact your nearest YOKOGAWA dealer. • Only communication error messages are listed here. For other error messages, see the User’s Manual IM 710105-02E.
Page 335 Appendix 2 Error Messages Code Message Corrective Action Page Invalid string data. The parameter is either too long, or it contains an 4-7 and unusable character. chapter 5 String data not allowed. Use a data type other than <String data>. 4-6 and chapter 5 Invalid block data.
Page 336: Error Messages
Appendix 2 Error Messages Communication Query Errors (400 to 499) Code Message Corrective Action Page Query INTERRUPTED. Check the transmission and reception order. Query UNTERMINATED. Check the transmission and reception order. Query DEADLOCKED. Keep program messages to 1024 bytes or less in length, including <PMT>.
Page 337: Index
Index Symbols command ................4-3 Page Common Command Group ..........5-291 <Boolean> ................4-7 common commands ............. 4-3 <Current> ................4-6 COMMunicate Group............5-81 <Frequency> ................ 4-6 communication status ............5-226 <NRf> ................4-6, 4-7 computation (waveform) ........... 5-123 <Time> ................. 4-6 condition register ............
Page 338 Index marker cursor ..............5-85 Page MATH Group ..............5-123 GO/NO-GO determination ..........5-104 MEASure Group ............... 5-128 buzzer ................ 5-104 menu language ..............5-230 email notification ............5-104 mesial ................5-140 hard copy ..............5-104 message ................4-1 parameters ..............5-105 message language ............
Page 339 Index built-in printer output ........... 5-111 action-on-trigger ............5-232 file, saving to ............... 5-118 A Delay B trigger ............5-233 network printer output ..........5-111 CAN bus signal trigger ..........5-233 SDC ..................3-6 CAN FD bus signal trigger ......... 5-266 SEARch Group ..............
Page 340 Index waveform search .............. 5-146 waveform, total number of data points ......5-280 waveform zone determination .......... 5-108 waveform zone search ............5-116 waveform zoom ..............5-289 window function ..............5-99 word format............... 5-280 WPARameter Group ............5-282 Page XY Group ................5-286 Page zone (GO/NO-GO determination) ........

YOKOGAWA DLM2000 Series User Manual

Chapter 1 USB Interface

Chapter 2 Ethernet Interface (Optional)

Chapter 3 GP-IB Interface (Optional)

App

Chapter 4 Programming Overview Index

Chapter 5 Commands

Chapter 6 Status Reports

Appendix

Index

Quick Links

Communication Interface

Need help?

Questions and answers

Related Manuals for YOKOGAWA DLM2000 Series

Summary of Contents for YOKOGAWA DLM2000 Series

Table of Contents