Canon iPF6100 Service Manual page 680

Chapter 8
Display massage
Hardware error.
03130031-2E23
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2E25
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2E26
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2E27
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2E2A
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F2B
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2E2E
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F32
Turn off printer, wait, then
turn on again.
Calibration
There is a problem with the
multi-sensor.
Cancel calibration.
Calibration
There is a problem with the
multi-sensor.
Cancel calibration.
Hardware error.
03130031-2F3A
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F3B
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F3C
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F3D
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F3E
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F3F
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F46
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F48
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F49
Turn off printer, wait, then
turn on again.
Hardware error.
03130031-2F4A
Turn off printer, wait, then
turn on again.
8-32
Code*
03130031-2F23 Purge motor error
Pump inoperable
03130031-2F25 Unable to detect the carriage motor home position
03130031-2F26 Carriage inoperable
03130031-2F27 Carriage move timeout
03130031-2F2A Unable to detect the feed roller home position
03130031-2F2B LF operation failure
03130031-2F2E Roll travel timeout
03130031-2F32 Multi sensor error
03130031-2F35 Color calibration disabled
03130031-2F35 The detection value of the temperature/humidity
sensor was the ranges that were adjustment
impossibility when performing color calibration.
03130031-2F3A Valve motor error
03130031-2F3B CS communication error
03130031-2F3C LF pressure error
03130031-2F3D HP maintenance jet pump motor overload error
03130031-2F3E HP maintenance jet pump motor move timeout error Check the purge unit.
03130031-2F3F HP maintenance jet pump motor error
03130031-2F46 Platen shutter failure
03130031-2F48 VH voltage error
03130031-2F49 Left printhead short-circuit error detection (VH
leakage)
03130031-2F4A Incorrect main controller PCB attachment error
Condition detected Action
Check the purge unit.
Check the carriage unit.
Check the linear encoder for smears.
Check the carriage unit and surrounding parts.
Check the carriage unit and surrounding parts.
Check the feed roller encoder and surrounding part.
Check to see if paper has not jammed.
Check to see if paper has not jammed.
Check the feed motor and feed roller.
Check the roll feed unit.
Check the environment for interferences from
outside light.
Replace the multi sensor unit.
Check the parts counter in service mode.
Replace the multi sensor unit.
Check the paper on which a pattern is printed for
smears.
Check the environment for interferences from
outside light.
Clean the printhead.
Check the ink supply unit.
Remove the ink tanks and then reload them.
Replace the ink tank.
Check the main controller PCB.
Check the pinch roller and surrounding parts.
Replace the pinch roller pressure drive unit.
Check the purge unit.
Check the purge unit.
Check the platen shutter and shutter HP sensor.
Check the power supply unit.
Check that the left printhead is attached correctly.
Check the contact of left printhead and surrounding
parts.
Replace the left printhead.
Replace the carriage unit.
Check the main controller PCB.
Replace the correct main controller PCB.