Canon iPF6100 Service Manual page 679

Display massage
Roll printing is selected. 03060A00-2E00
Press Load/Eject and load a
roll.
No Roll Feed Unit. 03060A00-2E0E
Turn printer off and install
roll feed unit.
The roll is empty. 03060A00-2E1B
Lift the release lever and
replace the roll.
Roll feed unit error. 03060A00-2E24
Turn off the printer and
check the roll feed unit.
03060A00-2E33
Roll printing is selected. 03060A00-2E35
Press Load/Eject and load a
roll.
Roll printing is selected. 03060A00-2E37
Roll feed unit error. 03060B00-2E24
Turn off printer and check
roll feed unit.
Wrong paper type. 03061000-2E15
This type of paper is not 03061000-2E15
compatible with HP-GL/2.
Online: Print
Stop: Stop Printing
Load/Eject: Change Paper
PaprWidth Mismatch. 03063000-2E08
Hardware error. 03130000-2E21
03130000-2E21
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-260E
03130031-260E
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-260F
03130031-260F
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2618
03130031-2618
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-290A
03130031-290A
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2E23
03130031-2E23
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F13
03130031-2E13
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F14
03130031-2E14
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F16
03130031-2E16
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F17
03130031-2E17
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F1F
03130031-2E1F
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F20
03130031-2E20
Turn off printer, wait, then
turn on again.
Hardware error. 03130031-2F22
03130031-2E22
Turn off printer, wait, then
turn on again.
Code* Condition detected
Data with a roll media specification has been received
but no roll media are loaded.
Roll media unit not installed
Roll media end
Roll cam sensor error
Roll media is not loaded when receiving the printing
job.
Roll media is not loaded for internal printing.
Roll media is not loaded when printing.
Roll feed unit failure
Paper type mismatch
Non-support media of HP-GL/2
Roll media width mismatch
IEEE1394 port error
Gap detection error
Gap reference surface error
VH voltage error
HDD unit detection error
Cutter unit failure
A/D converter external trigger output stop detection
hardware error 1
Writing to the ASIC register disabled
Mist fan rotation error
Platen suction fan lock detection error
Pump cam sensor error
Purge motor cam position error
Pump move timeout
Action
Load roll media.
Install the roll media unit.
Renew the supply of roll media.
Check the roll unit.
Set the roll media.
Reload the roll media.
Set the roll media.
Replace the roll feed unit.
Check the type of paper that can be fed and reload
the paper.
Exchange for the compatible paper to HP-GL/2
before reprinting.
Change the roll media.
Check the IEEE1394 board is attached correctly.
Replace the IEEE1394 board.
Replace the main controller PCB.
Check the carriage unit and surrounding parts.
Replace the main controller PCB.
Replace the multi sensor reference.
Check the power supply unit.
Check the HDD unit is attached correctly.
Check the HDD unit and surrounding parts.
Replace the HDD unit.
Check the cutter unit and sensor.
Replace the new printhead.
Replace the main controller PCB
Check the mist fan.
Check the platen suction fan.
Check the purge unit.
Check the purge unit.
Check the purge unit.
Chapter 8
8-31