Canon iPF6100 Service Manual page 678

Chapter 8
Display massage
Paper size not detected.
Lift the release lever and
reload the paper.
Leading edge detection
error.
Lift the release lever and
align leading edge with
orange line.
This paper cannot be used.
Check supported paper
sizes.
This paper cannot be used.
Check supported paper
sizes.
Paper jam.
Manually rewind roll all the
way.
Paper size not detected.
Lift the release lever and
reload the paper.
Paper size not detected.
Lift the release lever and
reload the paper.
Cannot print as specified.
Lift the release lever and
replace paper with A4/LTR
(vertical) or larger.
Cannot print as specified.
Lift the release lever and
replace paper with A3/
Ledger (vertical) or larger.
Cannot print as specified.
Lift the release lever and
replace roll with 10 in. wide
or larger roll.
Cannot feed paper.
Remove paper and press
Load/Eject.
Cannot feed paper.
Lift the release lever and
reload paper.
Paper jam.
Manually rewind roll all the
way and press OK.
Paper jam.
Manually rewind roll all the
way and press OK.
Error in cutter position.
Hardware error.
03130031-2E29
Turn off printer, wait, then
turn on again.
Use another paper.
Press Online to clear the
error.
Paper loaded askew.
Lift the release lever.
Ink tank cover is open.
Turn off printer,wait a
while, and turn it on again.
Rel lever is in wrong
position.
Turn off printer, wait, then
turn on again.
Top cover is open.
Turn off printer, wait a
while, and turn it on again.
Paper mismatch.
Make sure media type and
paper size match for the
adjustment print.
Sheet printing is selected.
8-30
Code*
03010000-200C Unable to detect the leading end of paper
03010000-200D Unable to detect the trailing end of cut sheet
03010000-200E Undersized paper (cut sheets/roll media)
03010000-200F Oversized paper (cut sheets/roll media)
03010000-2016 Cut sheet feed failure
03010000-2017 Paper (right) edge detection error
03010000-2018 Paper (left) edge detection error
03010000-201A Paper (right) edge detection error (cut sheet pick-up) Set or replace the media.
03010000-201B Paper (right) edge detection error (roll media pick-up) Set or replace the media.
03010000-201C Paper (left) edge detection error (cut sheet pick-up)
03010000-201D Paper (left) edge detection error (roll media pick-up) Set or replace the media.
03010000-2E1F Undersized paper loaded for internal printing (A4 or
larger)
03010000-2E1F Undersized paper loaded for internal printing (A3 or
larger)
03010000-2E1F Undersized paper loaded for internal printing (roll
media)
03010000-2E25 Paper jam while feeding/ejecting/printing
03010000-2E27 Paper jam during feeding/printing/ejection
03010000-2E3A Madia load failure
03010000-2E3B Madia load failure (lower roll)
03010000-2E47 Cutter position error
03010000-2F29 Feed motor timeout (Roll media)
03010000-2F33 Unadjustable because of transparent media
03016000-2010 Skew
03031000-2E10 Ink tank cover abnormally open
03031000-2F21 Pinch roller open error
03031000-2F38 Top cover abnormally open
03060000-2E20 Cut sheet type or size is not match when printing the
printhead registration.
03060100-2E02 Cut sheet is not loaded when printing.
03060100-2E05 Cut sheet is not loaded when receiving the printing
job.
Condition detected Action
Check the leading end of paper.
Reload the paper.
Check the sheet length.
Check to see if paper has not jammed.
Replace with larger-sized paper.
Replace with smaller-sized paper.
Check or replace a cut sheet.
Check the right edge of paper.
Check the paper type.
Check the left edge of paper.
Check the paper type.
Set or replace the media.
Replace with A4/Letter or any larger-sized paper.
Replace with A3/11"x17" or any larger-sized paper.
Replace with roll media at least 10 inches in width.
Remove the paper jam and reload the paper.
Reload the paper.
Check the pick-up unit and roll media.
Check to see if paper has not jammed.
Check the pick-up unit and roll media.
Check to see if paper has not jammed.
Check the cutter unit and surrounding part.
Check the roll feed unit.
Check roll media.
Check to see if paper has not jammed in the printer.
Replace with adjustable media.
Correct the skew in the paper and reload it.
Close the ink tank cover and turn on the printer
again.
Check the pinch roller unit and surrounding part.
Close the top cover and turn on the printer again.
Change the cut sheet.
Set the cut sheet.
Set the cut sheet.