Using The Menus - Extron electronics Annotator User Manual

Using the menus
To configure the Annotator using any of the above menus, do the following:
1.
2.
3.
N Pressing the Menu button within any level takes the user back to the current top
Input
User
Menu
Configuration
Presets
Next
Next
Recall Preset
Input #x
<NA>
RGB
Rotate either to
Rotate
select a preset to
video input type.
recall settings.
Next
Next
Input #x
Save Preset
Film Detect On
<02>
Rotate
Rotate either
Film Detect on
to select a preset
or off.
to save current
Next
settings to.
Input #x
Vert Start 128
Rotate to adjust
Vertical Start value.
Next
Input #x
Horz Start 128
Rotate
Horizontal Start value.
Next
Input #x
Pixel Phase 28
Rotate
Pixel Phase value.
Next
Input #x
Total Pix *2200
Rotate
Total Pixel value
(* = default).
Next
Input #x
Active Pixels *1920
Rotate
Active Pixels value
(* = default).
Next
Input #x
Active Lns *1080
Rotate
Active Lines value
(* = default).
*N To activate the hidden menu "Edit Comms",
press and hold Detail and Color/Tint buttons
simultaneously, then press Next.
**N The Scan Coverter Settings menu is only
available when an optional Scan Converter
I/O board is installed.
Press the Menu button repeatedly to get to the desired configuration menu.
Press the Next button repeatedly to go to the desired submenu.
The LCD shows the current values. Observe the LCD and rotate either (or
both) adjust knob to change the values as desired.
level menu.
When in any menu for approximately 25 seconds and no buttons have been
pressed or adjust knobs rotated, the unit times out and returns to the default
cycle.
Output
Menu
Menu
Configuration
Next
Resol 1024x768
Refresh 60.00Hz
Rotate to adjust
to select
Resolution value
Rotate to adjust
Refresh rate
Next
Output Type
RGBHV
to turn
Rotate either to
adjust Output
type value
Next
Sync Polarity
H Neg V Pos
1024x768 60.0Hz
Rotate either to
adjust Sync
Polarity values
to adjust
to adjust
to adjust
to adjust
MTP Pre-Peaking
to adjust
Indicates Internal temperature
(not adjustable)
Calibrate Panels
Press Size to callibrate
panel sizes
Reset to Factory
Press Detail to reset unit
to factory settings
Advanced View Comm
Menu
Settings
Configuration
Next
Next
Auto Image
Serial Port
Input #x Off 9600 RS232
Rotate to turn Next
Auto Image mode
MAC Address
On or Off
005A6003C24
Next
This is set at the factory
Auto Memories
and cannot be changed
On
in "Edit Comm Settings"
menu.
Next
Rotate either to turn
Auto Memories On
or Off
DHCP Mode
On
Next
Next
Input EDID
IP Address
192.168.254.254
Rotate to adjust
Resolution value
Next
Rotate to adjust
Refresh rate
Subnet Mask
Next
255.255.000.000
RGB Delay
Next
0.5 Seconds
Gateway Address
Rotate either to adjust
000.000.000.000
RGB Delay value
Next
"Hidden" Menu *
Switch Effect
Edit Comm
Dissolve
Settings
Rotate either to
Next
change Switch Effect
Next
Serial Port
9600 RS232
Test Pattern
Color bars Rotate
RS-232 or RS-422
Rotate either to
mode. Rotate
change Test Pattern
change baud rate.
Next
Next
DHCP Mode
<On>
Off
Rotate either to turn
Rotate either to turn
DHCP mode On or Off.
MTP Pre-Peaking
Next
On or Off
Next
IP Address
<192>168.254.254
Internal temp
96 F 35 C
Rotate
octet field. Rotate
to change address.
Next
Next
Subnet Mask
<255>255.000.000
Press size
Rotate
octet field. Rotate
to change address.
Next
Next
Gateway Address
Press Detail
<000>000.000.000
Rotate
octet field. Rotate
to change address.
Annotator • Front Panel Operation
Exit Menu
Menu
Press NEXT
Optional I/O
Board Menu **
Scan Converter
Settings
Next
H Size V
2048 2048
Rotate to adjust
H value. Rotate
to adjust V value.
Next
H Center V
2048 2048
Rotate to adjust
H value. Rotate
to adjust V value.
Next
Output Format
S-video/Comp
Rotate either to
select output format.
Next
Output Standard
NTSC
Rotate either to
select output standard.
Next
Flicker Filter
3
to select
Rotate either to
to
adjust flicker filter.
Next
H Filter
0
Rotate either to
adjust H filter.
Next
Encoder Filter
0
to select
Rotate either to
adjust encoder filter.
to select
to select
3-5