Glossary Of Terms - AT&T TL91270 User Manual

Bluetooth

Glossary of terms

Below are some terms used in this user's manual to help you become
familiar with using your Bluetooth devices and your new AT&T telephone
system.
Active devices - a maximum of two paired devices (two cell phones, or one
cell phone and one headset) on the active devices list can be connected to
the telephone base, but only one cell phone or headset can be on a call at
a time.
Bluetooth cell phone - refers to a mobile Bluetooth enabled cellular
telephone.
CELLULAR line - the communications service provided through your
Bluetooth enabled cellular telephone.
Connected - a Bluetooth enabled device (cell phone or headset) can only be
used when it is connected to the telephone base. When a Bluetooth enabled
device is connected to the telephone base and active on the active devices
list, it will be ready for use.
Disconnected - a diagonal line appears across devices 1 and/or 2 when
the corresponding Bluetooth enabled device is disconnected from the
telephone base.
Discoverable mode - before a Bluetooth enabled device can be paired, it
must be set to this mode. When pairing your cell phone, the telephone base
will be set to this mode. When pairing a headset, the headset must be set to
this mode. Depending on the manufacturer, this mode is sometimes referred
to as Find Me or Visibility.
HOME line - your conventional telephone land line. On your TL92270/
TL92370 handset, press HOME/
FLASH
Paired devices - once a Bluetooth device has been paired with the
telephone base, it will be identified as registered to the telephone base. Only
one Bluetooth cellular phone can be paired with the telephone base.
Pairing - this refers to the process of two Bluetooth devices registering
device information with each other. The telephone base must be paired
with a Bluetooth cellular phone before the Bluetooth device can be used.
Depending on the manufacturer, this is also referred to as Bonding.
PIN - by default, the PIN is 0000 for the telephone base and for most
Bluetooth devices. PIN information must be exchanged between Bluetooth
devices before they can be used. This is also known as a passkey
or passcode.
to use the home line.
13
Bluetooth
Bluetooth setup
To use a Bluetooth enabled cellular phone with your telephone, you must
first pair and connect your Bluetooth cellular phone with the telephone base.
All TL92270/TL92370 handsets can be used to make or answer on the cell
phone line.
Bluetooth wireless technology operates within a short range. When you pair
a Bluetooth cell phone or Bluetooth headset to the telephone base, move
closer to the telephone base to maintain sufficient signal strength.
Pairing a device
Before you begin, make sure that you have cellular coverage and your
Bluetooth enabled cell phone is not connected to any other Bluetooth
device. Refer to your cell phone user's manual to learn how to search for or
add new Bluetooth devices.
To pair and connect a cell phone:
1. Press MENU/ on the handset when it is not in use.
SELECT
2. Press CID or DIR to highlight Bluetooth, then press
/SELECT.
MENU
3. Press CID or DIR to highlight Add cellular, then
press /SELECT. The screen displays ADD CELLULAR
MENU
Place cell phone next to base. Press SELECT.
• If there are already four paired devices on the paired
devices list, the screen will show Maximum of 4
devices can be paired and prompt you to
replace an existing paired device (page 21).
4. Press /SELECT. The screen displays
MENU
Please set your cell phone to search for devices, then
press SELECT.
• If a device is already connected to the telephone
base, the screen displays Connected device will
be temporarily disconnected. Press SELECT. Press
/SELECT to temporarily disconnect the device
MENU
and continue the pairing process.
5. Turn on the Bluetooth feature of your cell phone and search for or add
new devices.
6. Press /SELECT to set the telephone base to discoverable mode.
MENU
7. Once your cell phone finds AT&T DECT 6.0, press
Answering sys
Directory
Cal l log
Intercom
Bluetooth
BLUETOOTH
Download dir
Add cel lular
Add headset
Active devices
ADD CELLULAR
Place cel l
phone next to
base.
Press SELECT
Please set your
cel l phone to
search for
devices, then
press SELECT
/SELECT.
MENU
14