HPE FlexFabric 5950 Series Configuration Manual page 396

# On PE 1, enable BGP in AS 200, and specify the MCE as its EBGP peer.
[PE1] bgp 200
[PE1-bgp-default] ip vpn-instance vpn1
[PE1-bgp-default-vpn1] peer 30.1.1.1 as-number 100
[PE1-bgp-default-vpn1] address-family ipv4
[PE1-bgp-default-ipv4-vpn1] peer 30.1.1.1 enable
[PE1-bgp-default-ipv4-vpn1] quit
[PE1-bgp-default-vpn1] quit
[PE1-bgp-default] quit
# Use similar procedures to configure VPN 2 settings on MCE and PE 1. (Details not shown.)
V erifying the configuration
5 7 6 B
# Verify that PE 1 has learned the OSPF route of VPN 1 through BGP.
[PE1] display ip routing-table vpn-instance vpn1
Destinations : 13
Destination/Mask
0.0.0.0/32
30.1.1.0/24
30.1.1.0/32
30.1.1.2/32
30.1.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32 Direct
192.168.0.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32 Direct
# Verify that PE 1 has learned the OSPF route of VPN 2 through BGP.
[PE1] display ip routing-table vpn-instance vpn2
Destinations : 13
Destination/Mask
0.0.0.0/32
40.1.1.0/24
40.1.1.0/32
40.1.1.2/32
40.1.1.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32 Direct
192.168.10.0/24
224.0.0.0/4
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
0 0
BGP 255 3
Direct 0 0
Direct 0 0
0 0
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
0 0
BGP 255 3
Direct 0 0
388
NextHop Interface
127.0.0.1 InLoop0
30.1.1.2 Vlan30
30.1.1.2 Vlan30
127.0.0.1 InLoop0
30.1.1.2 Vlan30
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
30.1.1.1 Vlan30
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0
NextHop Interface
127.0.0.1 InLoop0
40.1.1.2 Vlan40
40.1.1.2 Vlan40
127.0.0.1 InLoop0
40.1.1.2 Vlan40
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
40.1.1.1 Vlan40
0.0.0.0 NULL0