HPE FlexFabric 5950 Series Configuration Manual page 108
Mpls
Hide thumbs
Also See for FlexFabric 5950 Series:
- Command reference manual (363 pages) ,
- Configuration manual (94 pages) ,
- Installation manual (53 pages)
Table of Contents
Advertisement
[SwitchC-Vlan-interface2] mpls te enable
[SwitchC-Vlan-interface2] quit
4.
Configure MPLS TE attributes of links:
# Set the maximum link bandwidth and maximum reservable bandwidth on Switch A.
[SwitchA] interface vlan-interface 1
[SwitchA-Vlan-interface1] mpls te max-link-bandwidth 10000
[SwitchA-Vlan-interface1] mpls te max-reservable-bandwidth 5000
[SwitchA-Vlan-interface1] quit
# Set the maximum link bandwidth and maximum reservable bandwidth on Switch B.
[SwitchB] interface vlan-interface 1
[SwitchB-Vlan-interface1] mpls te max-link-bandwidth 10000
[SwitchB-Vlan-interface1] mpls te max-reservable-bandwidth 5000
[SwitchB-Vlan-interface1] quit
[SwitchB] interface vlan-interface 2
[SwitchB-Vlan-interface2] mpls te max-link-bandwidth 10000
[SwitchB-Vlan-interface2] mpls te max-reservable-bandwidth 5000
[SwitchB-Vlan-interface2] quit
# Set the maximum link bandwidth and maximum reservable bandwidth on Switch C.
[SwitchC] interface vlan-interface 2
[SwitchC-Vlan-interface2] mpls te max-link-bandwidth 10000
[SwitchC-Vlan-interface2] mpls te max-reservable-bandwidth 5000
[SwitchC-Vlan-interface2] quit
5.
Configure an MPLS TE tunnel on Switch A:
# Configure MPLS TE tunnel interface Tunnel 0.
[SwitchA] interface tunnel 0 mode mpls-te
[SwitchA-Tunnel0] ip address 6.1.1.1 255.255.255.0
# Specify the tunnel destination address as the LSR ID of Switch C.
[SwitchA-Tunnel0] destination 3.3.3.3
# Configure MPLS TE to use a static CRLSP to establish the tunnel.
[SwitchA-Tunnel0] mpls te signaling static
[SwitchA-Tunnel0] quit
6.
Create a static CRLSP:
# Configure Switch A as the ingress node of the static CRLSP, and specify the next hop
address as 2.1.1.2, outgoing label as 20, and bandwidth for the tunnel as 2000 kbps.
[SwitchA] static-cr-lsp ingress static-cr-lsp-1 nexthop 2.1.1.2 out-label 20
bandwidth 2000
# On Switch A, configure tunnel 0 to use static CRLSP static-cr-lsp-1.
[SwitchA] interface Tunnel0
[SwitchA-Tunnel0] mpls te static-cr-lsp static-cr-lsp-1
[SwitchA-Tunnel0] quit
# Configure Switch B as the transit node of the static CRLSP, and specify the incoming label as
20, next hop address as 3.2.1.2, outgoing label as 30, and bandwidth for the tunnel as 2000
kbps.
[SwitchB] static-cr-lsp transit static-cr-lsp-1 in-label 20 nexthop 3.2.1.2 out-label
30 bandwidth 2000
# Configure Switch C as the egress node of the static CRLSP, and specify the incoming label as
30.
[SwitchC] static-cr-lsp egress static-cr-lsp-1 in-label 30
100
Advertisement
Table of Contents
