Cisco web site appendix. NOTE: This guide doesn’t apply to Cisco TelePresence SX10 Quick Sets that are registered to Cisco Spark. To find more information on Cisco Spark room systems, visit: https://www.help.webex.com Cisco TelePresence SX10 API Reference Guide CE8.2, SEPTEMBER 2016.
Touch 10 controller to a video System is managed by Cisco and if there are any issues, wise upgrading to CE8 can leave you with a system. All user credentials can be used for this purpose.
A visual update has been applied to the Setup and Pairing Wizard on the Touch 10. The Touch 10 has a new GUI when registered to Cisco Spark, which is similar to the Cisco TelePresence SX10 on-screen user interface. If the endpoint is registered to on-premise infrastructure, the Touch 10 controller has the same user interface as CE8.1.
The Room http://www.cisco.com/c/en/us/support/collab- system’s web interface. You can also work offline with a System is managed by Cisco and if there are any issues, oration-endpoints/telepresence-quick-set-series/ stand-alone version of the editor. The editor is available contact Cisco Technical Assistance center through the products-release-notes-list.html...
Echo <on/off> Refer to ”Configurations” on page can be used for advanced troubleshooting together with Cisco technical support. Systemtools are not a part of the If echo is set to the key inputs are displayed when enter- programming API. Refer to ”The SystemTools commands”...
Network  IPv4 Assignment Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Security. Define how the system will obtain its IPv4 address, subnet mask and gateway address. This setting only applies to systems on IPv4 networks.
: Auto/Manual/Off xConfiguration Network QoS Diffserv NTP: Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. where If CDP is not available, VLAN is not enabled. : Index that identifies the network. Range: 1..1 Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting.
NetworkServices CDP Mode setting is switched Off, you cannot use the web interface. Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the If you need extra security (encryption and decryption of requests, and pages that are returned endpoint report certain statistics and device identifiers to a CDP-enabled switch.
These variables can then "public". If you have the Cisco TelePresence Management Suite (TMS) you must make sure the be queried (set to ReadOnly) and sometimes set (set to ReadWrite) by managing applications.
Provisioning ExternalManager AlternateAddress Select the HTTP method to be used for the provisioning. Only applicable when the endpoint is provisioned by Cisco Unified Communication Manager (CUCM) and an alternate CUCM is available for redundancy. Define the address of the alternate Requires user role: ADMIN, USER CUCM.
When the video system emits ultrasound, Proximity clients can detect that they are close to the Default value: "" video system. In order to use a client, at least one of the Proximity services must be enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the USAGE: Proximity services.
Number, Protocol, CallRate, CallType and Device. You can add several contact methods to a contact. Note that only the first contact method will appear in the Favorites list on the Cisco TelePresence Touch controller. The first contact Requires user role: ADMIN, USER method may have been created when issuing the xCommand Phonebook Contact Add command to make the contact.
Value space of the result returned: Unanswered/Ignored/Autoanswered/Answered xStatus Call [n] DeviceType Example: Indicates whether the remote system is a single endpoint or an MCU. Some Cisco endpoints xStatus Call AnswerState (SX20, SX80, MX200 G2, MX300 G2) have built-in MCU capabilities. *s Call 5 AnswerState: Answered...
Shows whether or not the SSL certificate of the server that the video system / codec tries to xStatus Standby State register to is included in the codec’s trusted CA-list. The server is typically a Cisco VCS or CUCM. *s Standby State: Off ** end True: The server’s SIP certificate is checked against the trusted CA-list on the codec and found...
SystemUnit Hardware Module CompatibilityLevel *s SystemUnit Hardware Monitoring Fan 1 Status: "locked on 1096 rpm" The Cisco TelePresence endpoints are using a NAND flash memory for general storage. The ** end endpoints running TC software are manufactured with a new version of the flash memory.
IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, On our web site you will find an overview of the worldwide Cisco contacts. WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM Go to: http://www.cisco.com/web/siteassets/contacts...