03010000-200D Cut Media End Error; 03010000-2E1F/03060000-2E14/03060A00-2E00/03061000-2E15/03063000-2E08/03860002-2E02/03860002-2E0A/ 03860002-2E0C Path Mismatch Error; 03010000-2E1F/03060000-2E14/03060A00-2E00/03061000-2E15/03063000-2E08/03860002-2E02/03860002-2E0A/03860002-2E0C Path Mismatch Error; 03862000-2E09 Insufficient Roll Media Error - Canon iPF9000 series Service Manual

6.1.3.7 03010000-2016/03010000-2E27 Paper feed error

iPF9000
<Cause>
During paper feed or delivery, paper jammed or paper was fed improperly.
During printing, paper was fed out of the way.
During paper feed, delivery or printing, the feed motor has gone out of synchronization.
<Probable fault location>
Paper path, media sensor, feed roller encoder, feed roller HP sensor, feed motor, feed roller, or main controller PCB
<Countermeasure>
1) Visual check
Remove foreign substances from the paper path and media sensor if any.
If the paper feed surface or moving part of the paper path is damaged or deformed, replace the paper path.
2) Media sensor
Check for normal operation. If the operation is abnormal, replace the media sensor.
3) Replace the feed roller sensor unit
Check for normal operation. If the operation is abnormal, replace the feed roller sensor unit.
4) Replace the feed motor.
5) Replace the feed roller.
6) Replace the main controller PCB.

6.1.3.8 03010000-200D Cut media end error

iPF9000
<Cause>
When cut media was fed by the specified length, the media sensor could not detect the trailing edge of the cut media.
During printing, the media sensor detected the trailing edge of the cut media at the position different from that detected during cut media feed.
<Probable fault location>
Paper path, media sensor, feed roller encoder, feed roller HP sensor, feed motor, feed roller, or main controller PCB
<Countermeasure>
1) Visual check
Remove foreign substances from the paper path and media sensor if any.
If the paper feed surface or moving part of the paper path is damaged or deformed, replace the paper path.
2) Media sensor,
Check the media sensor for normal operation. If the operation is abnormal, replace the media sensor.
3) Replace the feed roller sensor unit
Check for normal operation. If the operation is abnormal, replace the feed roller sensor unit.
4) Replace the feed motor.
5) Replace the feed roller.
6) Replace the main controller PCB.
6.1.3.9 03010000-2E1F/03060000-2E14/03060A00-2E00/03061000-2E15/03063000-2E08/03860002-2E02/03860002-2E0A/
03860002-2E0C Path mismatch error
iPF9000
<Cause>
The size of the media used to print the adjustment pattern was smaller than the specified one.
The media size specified using the printer driver was different from the size of the actually loaded media.
No roll media was loaded when data was received with roll media specified as a media type.
The type of the loaded media was different from the media type specified using the printer driver.
No cut media was loaded when data was received with cut media specified as a media type.
Data requiring roll media was received when cut media were loaded.
Data requiring cut media was received when roll media was loaded.
<Probable fault location>
Media type or main controller PCB
<Countermeasure>
1) Media check
Check the loaded media. If the media type is different from that required by the send data, no media is loaded, or the size of the loaded media is not the specified
one, load correct media.
2) Replace the main controller PCB.

6.1.3.10 03862000-2E09 Insufficient roll media error

iPF9000
<Cause>
The machine detected that the remaining roll media was insufficient.
<Probable fault location>
Roll media or main controller PCB
<Countermeasure>
1) Replace the roll media.
Chapter 6
0014-2776
0013-8114
0012-6628
0013-7136
6-5