03010000-200D Cut Media End Error; 03010000-2016 Paper Feed/Delivery Jam Error; 03010000-2E1F/03060000-2E14/03060A00-2E00/03061000-2E15/03860002-2E02/03860002-2E0A/03860002-2E0C Path Mismatch Error - Canon iPF700 Series Service Manual

Chapter 6
If there is any print or stain in the detection area on the media or the media size is not the specified one, replace the media.
2) Media loading position check
If the media loading position is wrong, load the media again.
3) Visual check
Remove foreign substances from multi sensor if any.
4) Multi-sensor
Select [SERVICE MODE]>[DISPLAY]>[SYSTEM]>[SIZE CR] to check the value read by the multi sensor. If the value is wrong, replace the multi sensor.
5) Replace the head relay PCB.
6) Cable continuity check
If continuity of the cable between the head relay PCB and the carriage relay PCB is abnormal, replace the cable.
7) Replace the carriage relay PCB.
8) Cable continuity check
If continuity of the cable between the carriage relay PCB and the main controller PCB is abnormal, replace the cable.
9) Replace the main controller PCB.

6.1.4.2 03010000-200D Cut media end error

<Cause>
When cut media was fed by the specified length, the media sensor could not detect the trailing edge of the cut media.
During printing, the media sensor detected the trailing edge of the cut media at the position different from that detected during cut media feed.
<Probable fault location>
Paper path, media sensor, or main controller PCB
<Countermeasure>
1) Visual check
Remove foreign substances from the paper path and media sensor if any.
If the paper feed surface or moving part of the paper path is damaged or deformed, replace the paper path.
2) Media sensor,
Check the media sensor for normal operation. If the operation is abnormal, replace the media sensor.
3) Replace the main controller PCB.

6.1.4.3 03010000-2016 Paper feed/delivery jam error

<Cause>
During paper feed or delivery, paper jammed or paper was fed improperly.
During printing, paper was fed out of the way.
<Probable fault location>
Paper path, media sensor, or main controller PCB
<Countermeasure>
1) Visual check
Remove foreign substances from the paper path and media sensor if any.
If the paper feed surface or moving part of the paper path is damaged or deformed, replace the paper path.
2) Media sensor
Select [SERVICE MODE]>[I/O DISPLAY] to check the media sensor for normal operation. If the operation is abnormal, replace the media sensor.
3) Replace the main controller PCB.
6.1.4.4 03010000-2820/03010000-2821/03010000-2822/03010000-2823/03010000-2F33/031300312F32 Adjustment error
<Cause>
Auto head alignment selected from the user menu could not be carried out because the alignment patter read result was NG.
Auto LF adjustment selected from the user menu or in the service mode could not be carried out because the adjustment patter read result was NG.
Decentering correction selected in the service mode cannot be carried out because the correction pattern read result was NG.
Auto LF adjustment selected from the user menu or in the service mode could not be carried out because the head check patter read result was NG.
Adjustment cannot be carried out because the loaded media is transparent.
Optical axis adjustment selected in the service mode cannot be carried out because the adjustment pattern read result was NG.
When adjustment has been carried after selecting [SERVICE MODE]>[ADJUST]>[PRINT PATTERN]>[OPTICAL AXIS] or [SERVICE MODE]>[AD-
JUST]>[PRINT PATTERN]>[LF TUNING] in the service mode, check that photo glossy paper is used.
<Probable fault location>
Operation method, printhead, multi sensor, head relay PCB, carriage relay PCB, or main controller PCB
<Countermeasure>
1) Check whether the media type selected on the operation panel is the same as the type of the media used to print the adjustment pattern. If they are different, retry
adjustment using the media of the type selected on the operation panel.
2) If ink bleeds greatly, change the media.
3) Carry out head cleaning, and retry adjustment. If the adjustment result is poor, replace the printhead.
4) Replace the multi sensor, and then retry adjustment.
5) Replace the head relay PCB.
6) Replace the carriage relay PCB.
7) Replace the main controller PCB.
6.1.4.5 03010000-2E1F/03060000-2E14/03060A00-2E00/03061000-2E15/03860002-2E02/03860002-2E0A/03860002-2E0C
Path mismatch error
<Cause>
The size of the media used to print the adjustment pattern was smaller than the specified one.
The media size specified using the driver was different from the size of the actually loaded media.
No roll media was loaded when data was received with roll media specified as a media type.
The type of the loaded media was different from the media type specified using the driver.
No cut media was loaded when data was received with cut media specified as a media type.
Data requiring roll media was received when cut media were loaded.
Data requiring cut media was received when roll media was loaded.
6-4
0014-0977
0014-0981
0014-0995
0014-0979