Huawei AR2200-S Series Configuration Manual page 55

Huawei AR2200-S Series Enterprise Routers
Configuration Guide - Reliability
2.
3.
Issue 01 (2012-01-06)
<Huawei> system-view
[Huawei] sysname RouterB
[RouterB] interface gigabitethernet1/0/0
[RouterB-GigabitEthernet1/0/0] ip address 4.1.1.2 255.255.255.0
[RouterB-GigabitEthernet1/0/0] quit
# Assign an IP address to the interface of RouterC.
<Huawei> system-view
[Huawei] sysname RouterC
[RouterC] interface gigabitethernet1/0/0
[RouterC-GigabitEthernet1/0/0] ip address 2.1.1.2 255.255.255.0
[RouterC-GigabitEthernet1/0/0] quit
# Assign an IP address to the interface of RouterD.
<Huawei> system-view
[Huawei] sysname RouterD
[RouterD] interface gigabitethernet1/0/0
[RouterD-GigabitEthernet1/0/0] ip address 4.1.1.1 255.255.255.0
[RouterD-GigabitEthernet1/0/0] quit
# On RouterA, configure a static route to 4.1.1.0/24 of RouterD.
[RouterA] ip route-static 4.1.1.0 255.255.255.0 2.1.1.2 preference 80
# On RouterB, configure a static route to 2.1.1.0/24 of RouterA.
[RouterB] ip route-static 2.1.1.0 255.255.255.0 4.1.1.1 preference 80
Configure C-DCC on RouterA.
# Create dialer group 1 and configure a dialer rule in the group.
[RouterA] dialer-rule
[RouterA-dialer-rule] dialer-rule 1 ip permit
[RouterA-dialer-rule] quit
# Configure a serial interface.
[RouterA] controller e1 1/0/0
[RouterA-E1 1/0/0] pri-set
[RouterA-E1 1/0/0] quit
# Assign an IP address to PRI1/0/0:15, enable C-DCC, and configure the dialer number.
[RouterA] interface Serial 1/0/0:15
[RouterA-Serial1/0/0:15] ip address 3.1.1.1 24
[RouterA-Serial1/0/0:15] dialer enable-circular
[RouterA-Serial1/0/0:15] dialer-group 1
[RouterA-Serial1/0/0:15] dialer route ip 3.1.1.2 600502
[RouterA-Serial1/0/0:15] quit
# Configure a static route.
[RouterA] ip route-static 3.1.1.0 255.255.255.0 Serial 1/0/0:15 preference 60
Configure C-DCC on RouterB.
# Create dialer group 2 and configure a dialer rule in the group.
[RouterB] dialer-rule
[RouterB-dialer-rule] dialer-rule 2 ip permit
[RouterA-dialer-rule] quit
# Configure a serial interface.
[RouterB] controller e1 1/0/0
[RouterB-E1 1/0/0] pri-set
[RouterB-E1 1/0/0] quit
# Assign an IP address to PRI1/0/0:15, enable C-DCC, and configure the dialer number.
[RouterB] interface Serial 1/0/0:15
[RouterB-Serial1/0/0:15] ip address 3.1.1.2 24
[RouterB-Serial1/0/0:15] dialer enable-circular
[RouterB-Serial1/0/0:15] dialer-group 2
[RouterB-Serial1/0/0:15] dialer route ip 3.1.1.1 600501
[RouterB-Serial1/0/0:15] quit
# Configure a static route.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 Interface Backup Configuration
47