Huawei AR2200-S Series Configuration Manual page 136

Huawei AR2200-S Series Enterprise Routers
Configuration Guide - Reliability
[Huawei] sysname RouterB
[RouterB] interface gigabitethernet 1/0/0
[RouterB-GigabitEthernet1/0/0] ip address 192.168.1.1 24
[RouterB-GigabitEthernet1/0/0] quit
[RouterB] interface gigabitethernet 2/0/0.1
[RouterB-GigabitEthernet2/0/0.1] ip address 100.1.1.2 24
[RouterB-GigabitEthernet2/0/0.1] control-vid 1 qinq-termination
[RouterB-GigabitEthernet2/0/0.1] qinq termination pe-vid 100 ce-vid 10
[RouterB-GigabitEthernet2/0/0.1] arp broadcast enable
[RouterB-GigabitEthernet2/0/0.1] quit
[RouterB] interface gigabitethernet 2/0/0.2
[RouterB-GigabitEthernet2/0/0.2] ip address 200.1.1.2 24
[RouterB-GigabitEthernet2/0/0.2] control-vid 2 qinq-termination
[RouterB-GigabitEthernet2/0/0.2] qinq termination pe-vid 100 ce-vid 20
[RouterB-GigabitEthernet2/0/0.2] arp broadcast enable
[RouterB-GigabitEthernet2/0/0.2] quit
[RouterB] ospf
[RouterB-ospf-1] area 0
[RouterB-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[RouterB-ospf-1-area-0.0.0.0] network 100.1.1.0 0.0.0.255
[RouterB-ospf-1-area-0.0.0.0] network 200.1.1.0 0.0.0.255
[RouterB-ospf-1-area-0.0.0.0] quit
[RouterB-ospf-1] quit
# Configure RouterC.
<Huawei> system-view
[Huawei] sysname RouterC
[RouterC] interface gigabitethernet 1/0/0
[RouterC-GigabitEthernet1/0/0] ip address 192.168.2.2 24
[RouterC-GigabitEthernet1/0/0] quit
[RouterC] interface gigabitethernet 2/0/0
[RouterC-GigabitEthernet2/0/0] ip address 192.168.1.2 24
[RouterC-GigabitEthernet2/0/0] quit
[RouterC] ospf
[RouterC-ospf-1] area 0
[RouterC-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[RouterC-ospf-1-area-0.0.0.0] network 192.168.2.0 0.0.0.255
[RouterC-ospf-1-area-0.0.0.0] quit
[RouterC-ospf-1] quit
After the preceding configurations are complete, RouterA and RouterB can obtain the routes to
the peer IP address using OSPF, and can ping each other.
The following shows the output for RouterA:
[RouterA] display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destination/Mask
RouterA and RouterB can ping each other.
[RouterA] ping 192.168.1.1
PING 192.168.1.1: 56
Issue 01 (2012-01-06)
Destinations : 10
Proto
100.1.1.0/24 Direct 0
100.1.1.1/32 Direct 0
127.0.0.0/8 Direct 0
127.0.0.1/32 Direct 0
192.168.1.0/24 OSPF
192.168.2.0/24 Direct 0
192.168.2.1/32 Direct 0
192.168.2.2/32 Direct 0
200.1.1.0/24 Direct 0
200.1.1.1/32 Direct 0
200.1.1.2/32 Direct 0
data bytes, press CTRL_C to break
Reply from 192.168.1.1: bytes=56 Sequence=1 ttl=254 time=110 ms
Reply from 192.168.1.1: bytes=56 Sequence=2 ttl=254 time=60 ms
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Routes : 11
Pre Cost Flags NextHop
0 D 100.1.1.1
0 D 127.0.0.1
0 D 127.0.0.1
0 D 127.0.0.1
10 2 D 192.168.2.2
0 D 192.168.2.1
0 D 127.0.0.1
0 D 192.168.2.2
0 D 200.1.1.1
0 D 127.0.0.1
0 D 200.1.1.2
2 VRRP Configuration
Interface
GigabitEthernet2/0/0.1
GigabitEthernet2/0/0.1
InLoopBack0
InLoopBack0
GigabitEthernet1/0/0
GigabitEthernet1/0/0
GigabitEthernet1/0/0
GigabitEthernet1/0/0
GigabitEthernet2/0/0.2
GigabitEthernet2/0/0.2
GigabitEthernet2/0/0.2
128