Siemens SIMATIC ET 200S Installation And Operating Manual page 11

Tables
Table 1-1 Using Interface Modules in ET 200S with Fail-Safe Modules.................................................... 1-4
Table 1-2 Achievable Safety Classes in Safety Mode ............................................................................... 1-4
Table 1-3 Steps from Selecting the F-Modules to Commissioning ET 200S............................................. 1-5
Table 2-1 Assigning F-Power Modules to Terminal Modules .................................................................... 2-4
Table 2-2 Assigning F-Electronic Modules to Terminal Modules............................................................... 2-4
Table 2-3 Assigning Power Modules to Electronic Modules/Motor Starters and Safety Class (Safety
Integrity Level) ........................................................................................................................... 2-5
Table 2-4 Parameter Length of F-Modules in Bytes .................................................................................. 2-6
Table 2-5 Maximum Configuration per Voltage Group .............................................................................. 2-7
Table 3-1 Address assignment in the F-CPU............................................................................................. 3-1
Table 3-2 Addresses Occupied by Useful Data ......................................................................................... 3-2
Table 4-1 Conditions for Inserting and Removing Fail-Safe Modules During Operation........................... 4-5
Table 4-2 Minimum Duration of the Sensor Signals to Allow Correct Acquisition by the F-DI Module ..... 4-7
Table 5-1 Channel-Specific Diagnostics: Fault Types of Fail-Safe Modules ............................................. 5-6
Table 7-1 Overview of Achievable Safety Classes (Safety Integrity Levels) with PM-E F pm DC24V
PROFIsafe ................................................................................................................................. 7-2
Table 7-2 PM-E F pm DC24V PROFIsafe: Conditions for AK/SIL/Category ............................................. 7-3
Table 7-3 Table-Terminal Assignment of the TM-P30S44-A0 or TM-P30C44-A0................................... 7-10
Table 7-4 Parameters of the PM-E F pm DC24V PROFIsafe.................................................................. 7-15
Table 7-5 Diagnostic functions of the PM-E F pm DC24V PROFIsafe .................................................... 7-17
Table 7-6 Causes of Errors and Corrective Measures for Diagnostic Messages of the
PM-E F pm 24 VDC PROFIsafe .............................................................................................. 7-18
Table 7-7 Overview of Achievable Safety Classes (Safety Integrity Levels) with PM-E F pp DC24V
PROFIsafe ............................................................................................................................... 7-24
Table 7-8 PM-E F pp DC24V PROFIsafe: Conditions for AK/SIL/Category ............................................ 7-25
Table 7-9 Table-Terminal Assignment of the TM-P30S44-A0 or TM-P30C44-A0................................... 7-28
Table 7-10 Parameters of the PM-E F pp DC24V PROFIsafe................................................................... 7-31
Table 7-11 Diagnostic functions of the PM-E F pp DC24V PROFIsafe..................................................... 7-32
Table 7-12 Causes of Faults and Corrective Measures for Diagnostic Messages of the
PM-E F pp 24 VDC PROFIsafe ............................................................................................... 7-33
Table 7-13 PM-D F DC24V PROFIsafe: Conditions for AK/SIL/Category................................................. 7-38
Table 7-14 Terminal Assignment of the TM-PF30S47-F1 ......................................................................... 7-40
Table 7-15 Parameters of the PM-D F DC24V PROFIsafe ....................................................................... 7-42
Table 7-16 Diagnostic Functions of PM-D F DC24V PROFIsafe............................................................... 7-43
Table 7-17 Causes of Faults and Corrective Measures for Diagnostic Messages of the
PM-D F DC24V PROFIsafe ..................................................................................................... 7-44
Table 7-18 EM 4/8 F-DI DC24V PROFIsafe: Power Modules for AK/SIL/Category.................................. 7-47
Table 7-19 Parameters of the EM 4/8 F-DI DC24V PROFIsafe ................................................................ 7-51
ET 200S Distributed I/O System - Fail-Safe Modules
Hardware Installation and Operating Manual, 07/2005, A5E00103686-04
Table of contents
xi