Operating and installation instructions Wine conditioning unit To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en - AU, NZ M.-Nr. 09 507 300...
Contents Description of the appliance ......... 4 Accessories .
After Sales ............47 Information for Miele Galleries and Chartered Agents....48 Demo mode r.
Description of the appliance a For switching the f For setting the temperature appliance on/off (X for colder) b Optical interface g For confirming a selection (OK (only for service technicians) sensor) c For selecting the upper, middle or h For setting the temperature lower wine conditioning zone (Y for warmer) d For switching the DynaCool...
Audible tones Switches on/off the sensor tones and the door alarm. < Miele|Home Lights up if a Miele@home (available in selected communication module is connected and countries) signed on. Demo mode (only visible Switches off the Demo mode.
Description of the appliance a Lighting panel (in all 3 wine conditioning zones) b Bottle presenter c Active charcoal filter (in all 3 wine conditioning zones) d Flexible wooden shelf with noteboard e Touch controls for upper, middle and lower wine conditioning zones/ Isolator plate for thermal separation of zones f Glass door made from...
Original Miele care product for stainless steel Chalk – Each time the Original Miele Care Use the chalk supplied to write on the product for stainless steel is used, it magnetic strips (noteboards) on the forms a protective film against dirt wooden shelves.
Caring for the environment Disposal of the packing Disposing of your old material appliance The transport and protective packing Electrical and electronic appliances has been selected from materials which often contain materials which, if are environmentally friendly for disposal handled or disposed of incorrectly, and can normally be recycled.
They contain important notes on the installation, safety, operation and care of the appliance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Keep these instructions in a safe place and ensure that new users are familiar with the contents.
Furthermore, the appliance must not be operated in areas where explosions may occur. Miele cannot be held liable for damage resulting from improper or incorrect use of the appliance. This appliance is not intended for use by persons (including...
In the event of any damage: – avoid any flames or anything which creates a spark, – switch off at the mains and unplug the appliance, – ventilate the room where the appliance is located for several minutes, and – contact Miele for advice.
If the connection cable is faulty, it must only be replaced by a Miele approved service technician to protect the user from danger. Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead.
Repairs and other work by unqualified persons could be dangerous. Installation work and repairs to electrical appliances must only be carried out by a Miele approved service technician. The manufacturer's warranty will be invalidated if the appliance is not repaired by a Miele approved service technician.
If storing alcohol with a high percentage proof, make sure it is tightly closed and stored upright. Danger of explosion! Use only Miele Original spare parts. If spare parts or accessories from other manufacturers are used, the warranty will be invalidated, and Miele cannot accept liability.
Warning and Safety instructions Do not damage the refrigerant circuit. Cleaning and care Do not use any oils or grease on the door seal, as these will cause the seal to deteriorate and become porous with time. Do not use a steam-cleaning appliance to clean this appliance. Pressurised steam could reach the electrical components and cause a short circuit.
Warning and Safety instructions Disposal of your old appliance Before disposing of an old appliance, first make the door lock unusable. This way you will prevent children from accidentally locking themselves in and endangering their lives. Be careful not to damage any part of the pipework whilst awaiting disposal, e.g.
How to save energy Normal energy consumption Increased energy consumption Installation/ In a ventilated room. In an enclosed, unventilated Maintenance room. Protected from direct sunlight. In direct sunlight. Not situated near a heat Situated near a heat source source (radiator, oven). (radiator, oven).
Cleaning and care ^ Immediately after removing the protective foil, apply the Original The sensors in the control panel for the Miele Care product for stainless 3 temperature zones appear: the steel. upper, middle and lower wine conditioning zones. The selected wine...
Switching on and off Switching off Individual settings can be selected for each wine conditioning zone. ^ Touch the On/Off button. ^ Touch the sensor for the particular If the appliance does not switch off, zone of the appliance where you the system lock is activated! would like to select the settings.
Selecting further settings Certain settings on the appliance can only be selected in the settings mode. The door alarm is automatically disabled when the appliance is in ^ By touching the X or Y sensor, you settings mode. can now select whether the system lock is switched on or off: System lock 0 0: The system lock is switched off...
Selecting further settings Audible tones ) The appliance has audible tones such as the sensor tone and the the door and temperature alarms. ^ By touching the X or Y sensor, you The sensor tone and door alarm can be can now select: 0: Sensor tone off;...
Selecting further settings Display brightness s The display brightness can be adjusted to suit the lighting conditions of the room. ^ By touching the X or Y sensor, you The display brightness can be set from can now select the display levels 1 to 3.
Temperature and air quality Wine keeps on maturing depending on the surrounding conditions. The length Type of wine Recommended of time for which wine can be kept in drinking temp. good condition will therefore depend Light, fruity red +14 °C to +16 °C not only on the temperature but also on wine: the air quality.
Temperature and air quality Safety measures in the case of low Setting the temperature ambient temperatures You can set a different temperature for To protect wine from low temperatures, each of the 3 wine conditioning zones. a safety thermostat ensures that the temperature in the appliance cannot fall dramatically.
Temperature and air quality While the temperature is being set, the Temperature range temperature value will flash in the The temperature range for all wine display. conditioning zones is between 5 and 20 The following information appears in the °C. display when the sensors are touched: Temperature display –...
Temperature and air quality DynaCool (constant humidity) m Air quality and humidity A conventional refrigerator, with its low The DynaCool function increases the humidity level, is not the best place to relative humidity in the entire appliance. store wine. It is very important to store wine in an atmosphere with a high Humidity and temperatures in the humidity level so that the corks remain...
Temperature and air quality Switching off DynaCool Because DynaCool increases energy consumption and causes the appliance to be louder, you may want to switch if off from time to time. ^ Touch the DynaCool sensor so that it is no longer highlighted in yellow. Air filtering with active charcoal filters The active charcoal filters provide a...
Alarms Your appliance is fitted with a warning Switching off the alarm early system which ensures that the If the noise disturbs you, you can temperature in the three zones cannot switch the alarm off early if you wish. rise or fall unnoticed and impair the wine.
Alarms Door alarm The alarm will sound if the door is left open for more than 2 minutes. The sensor lights in the control panel for the 3 temperature zones will flash. The alarm symbol ; will light up constantly in the display.
Display lighting If you wish to display your bottles of Setting the duration of the display wine, you can set the interior lighting so lighting that it remains on when the door is The lighting duration for the display closed. lighting is set at 30 minutes at the Each wine conditioning zone is factory.
(X and Y). The adjustment occurs directly and continuously. If the lights are damaged, please contact Miele to arrange for them to By touching the respective sensor: be repaired. – The lighting becomes darker.
Storing wine bottles Wooden shelves Vibrations and being moved have a negative effect on the maturing process of wine, and thus can be detrimental to the taste of the wine. As far as possible, store bottles of the same type of wine beside each other on the same shelf.
Storing wine bottles Moving the wooden shelves Adjusting the wooden shelves The wooden shelves can be removed if The space between the individual slats required. on the shelves can be adjusted according to the size of the wine bottles ^ Pull out the wooden shelf on its rails being stored.
Storing wine bottles Bottle presenter Labelling the shelves To give yourself an overview of the The bottle presenter enables you to wines you are storing, you can write on display selected wines so that the label the magnetic strip on the front of the can be seen even when the door is wooden shelves.
Storing wine bottles Maximum capacity A total of 178 bottles (0.75 l; Bordeaux bottles) can be stored in the appliance, with 46 in the upper zone, 46 in the middle zone and 86 in the lower zone. A total of 178 bottles can only be achieved by using all of the wooden shelves.
Automatic defrost Condensate and frost can build up on the back wall of the refrigerator section while the compressor is running. You do not need to remove this, as it will defrost and evaporate automatically. The defrosted water flows into an evaporation system via a condensate channel and drain pipe.
Cleaning and care Before cleaning Do not let water get into the ^ Switch off the appliance. electronic unit or the appliance ^ Disconnect the appliance from the lighting. mains. Switch off at the wall and Do not use a steam cleaning withdraw the plug from the socket, or disconnect the mains fuse.
A build-up paint. of dust will increase the energy ^ The Original Miele Care product for consumption of the appliance. stainless steel can be used internally and externally on stainless steel...
^ Touch the sensors for setting the clockwise or anti-clockwise until it temperature (X or Y) repeatedly until clicks into place. 2 (time counter is reset) appears in the display. The active charcoal filters can be purchased from Miele (see back cover for contact details).
Active charcoal filters ^ Touch the OK sensor to confirm your selection. The selected setting is adopted and the symbol will flash. ^ Press the settings sensor to leave the settings mode. If no sensor is touched, the appliance will automatically leave the settings mode after approx.
Miele. If, after reading this guide, you cannot remedy the problem yourself, please call Miele (see back cover for details). However, please note that a call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these operating instructions.
Problem solving guide The compressor is switching on too frequently and for too long, which is causing the temperature in the appliance to decrease. Problem Possible cause Remedy ^ Check the temperature The temperature The temperature inside the settings. inside the appliance has been set too low.
A bar lights up or Only temperatures within flashes in the the range the appliance can temperature display will be shown. display. ^ Call Miele. "F1" to "F3" or "S1" There is a fault. to "S9" will appear.
Problem solving guide Interior lighting Problem Possible cause Remedy ^ Call Miele. The interior To avoid overheating, the lighting doesn't lighting switches itself off automatically after approx. The light covers must not come on. 15 minutes if the door is left be removed.
Problem solving guide Other problems Problem Possible cause Remedy An alarm doesn't This is not a fault. The audible sound even though alarm has been switched off in the appliance door the settings mode (see has been left open "Selecting further settings - for a long time.
Noises Normal noises What causes them Brrrrr ... A humming noise is made by the motor (compressor). This noise can get louder for brief periods when the motor switches on. Blubb, blubb ... A gurgling noise can be heard when coolant is circulating through the pipes.
In the event of a fault which you cannot correct yourself, please contact: – Miele. You will find the address and telephone number of Miele on the back cover of the manual. When contacting Miele, please quote the model and serial number of your appliance.
Information for Miele Galleries and Chartered Agents Demo mode r The appliance can be displayed in the demo mode. This means the operation of the appliance and the interior lighting ^ Leave your finger on the X sensor will remain functional, but the appliance...
Information for Miele Galleries and Chartered Agents ^ Touch the X or Y sensor so that 0 appears in the display (demo mode is switched off). ^ Touch the OK sensor to confirm your selection. The selected setting is adopted and the r symbol will flash.
Electrical connection All electrical work should be carried out Do not connect the appliance to the by a suitably qualified and competent mains electricity supply by an extension person in strict accordance with current lead or a plug adapter. Extension leads local and national safety regulations.
Installation Location Climate range This appliance should be installed in a The appliance is designed for use dry, well-ventilated room. It should not within a certain climate range (ambient be installed where it is exposed to temperatures), and should not be used direct sunlight or directly adjacent to a outside this range.
Aligning the appliance against an adjacent wall and damaging the door and/or the wall. These pins are available to order from Miele. ^ Align the front feet using the flat spanner supplied with the appliance.
Installation Appliance dimensions...
Changing the door hinging The appliance is supplied with Removing the appliance door right-hand door hinging. If left-hand ^ Open the appliance door as far as it door hinging is required, the hinging will go. must be changed. To change the door hinging, you will need the following tools: ^ Carefully lift off the cover a at the Two people are needed to change...
Changing the door hinging Relocating the SoftClose mechanism ^ Press the cover f together in the middle and remove it. ^ Push the SoftClose mechanism c away from the appliance. ^ Undo the screws e from the SoftClose mechanism at the right and left-hand sides of the base of the door.
Changing the door hinging Caution! Do not move the front part of the SoftClose mechanism in the direction shown when the retaining clip b is removed. Risk of injury! ^ Remove the retaining clip b from the SoftClose mechanism. ^ Undo the screw h. ^ Pull the SoftClose mechanism c to the right and remove it.
Changing the door hinging Removing the appliance door ^ Pull the hinge pin l out from the top of the door. ^ Remove the covers j at the top of Tip: Leave the screw k in the hinge the appliance door using a pin until it is fitted on the other side of flat-bladed screwdriver.
Changing the door hinging Changing the hinging ^ Click the covers m into place at the top of the appliance. The cover with ^ Remove both covers m from the front the cut-out must be placed over the of the appliance. hinge.
Changing the door hinging ^ Unscrew the hinge q from the base ^ Remove the cover t at the base of of the appliance. the appliance. ^ Unscrew the foot o from underneath ^ Undo the screw u from the base of the hinge.
Changing the door hinging ^ Screw the hinge pin p onto the foot ^ Push the hinge pin l in far enough o from above, paying attention to the so that the groove on the pin is in line position of the groove in the hinge with the hole in the hinge.
Changing the door hinging ^ Pull the arm of the SoftClose ^ Unscrew the foot on the lower hinge mechanism c to its mount r on the until it touches the floor. Then hinge. unscrew it another quarter of a turn. Aligning the sides of the appliance door If the appliance door is not parallel with...
Changing the door hinging ^ Lower the cover so that it is in a vertical position. ^ Loosen the 3 screws on the hinge and slide it either to the left or to the right. ^ Tighten the screws again. ^ Then refit the cover.
KWT 6831 SG en - AU, NZ M.-Nr. 09 507 300 / 01...